GBC HeatSeal Sprint H925 Instruction Manual page 7

HeatSeal Sprint H925 - Troubleshooting
®
SYMPTOMS POSSIBLE CAUSE
Power cord is not plugged
into live power outlet
No power. Switch does
not illuminate when in
Circuit breaker has tripped
ON position.
Cover is open
No paper in feeder
Machine does not
respond after Idler bar assembly
pressing standby not latched
button
Main power switched off
Low film
Incorrect film setting
Ambient temperature is
Faint lines across
below 72°F/22°C
the document
Low line voltage
Cloudy lamination. Wavy
Incorrect film settings,
lamination. Unsatisfactory
insufficient heat
adhesion to media.
Media not compatible
with feeder
Print output not compatible
Feeder does not
with feeder
feed document
Paper is not fully inserted
into feeder
Sever paper curl
Paper side guides are not
adjusted squarely
Finished document
is skewed
Media is too smooth or slick
Paper curl is excessive
Feeder picks multiple
documents
Static electricity on media,
(add to existing)
or media is stuck together
Wrinkles in document EZload levers not closed
12
TM
CORRECTIVE ACTION
Plug into live outlet
Reset circuit breaker at
rear of machine
Close cover
Insert paper
Latch idler bar levers
Turn on power
Load new film
Select correct film setting
Operate at ambient
temperatures at or
above 72°F/22°C
Ensure correct voltage
is available
Verify and select correct
setting
Try different media
Try different printer
Fully insert paper into
feeder
Ensure paper is flat
Adjust paper side guides
to paper size
Feed one at a time or
change media type
Ensure paper is flat
Fan paper and replace
in feeder
Close EZload levers
HeatSeal Sprint H925 - Specifications
® TM
1. Warm-up time Note: If machine is warm, the warm up times are reduced. Standby mode is
activated after 30 minutes of non-use. To resume, press "Start" button.
3 mil / 75 mic
5 mil / 125 mic
2. Speed
A) The machine throughput speed is 31" (787.4mm) per minute
B) Equivalent to 4 Letter or A4 documents per minute
C) 25 Letter or A4 sheets take approximately 7 minutes
3 . Paper sizes and weights
Max paper weight
Min paper weight
Max paper width
Min paper width
Max paper length
4 . Border sizes
A4 paper (side border) 12" - 305 mm wide film
A4 paper (top & bottom border) 12" - 305 mm wide film
Letter paper (side border) 11.5" - 292 mm wide film
Letter paper (top & bottom border) 11.5" - 292 mm wide film
5. Film thickness
3 mil / 75 mic
5 mil / 125 mic
6. Feeder capacity
A) Maximum of 25 sheets at 20 lbs - 75 gsm
7. Machine weight
A) In box 85 lbs - 38.6 kg
B) Out of box 70 lbs - 32 kg
Max 2 minutes from cold
Max 2 minutes from cold
80 lbs cover - 216 gsm
20 lbs - 75 gsm
12" film, 11.6" - 295 mm
11.5" film, 11" - 279 mm
6" - 152 mm
48" - 1219 mm
0.15" - 4 mm
0.25" - 6 mm
0.25" - 6 mm
0.25" - 6 mm
Flexible
Semi Rigid
8. Dimensions (with exit tray open)
19" Wide x 31" High x 27" Deep
(483 mm Wide x 787 mm High x 686 mm Deep)
9. Electrical Specifications
A) 120v @ 60Hz, 7.5A
B) 230v, @ 50Hz, 4A
C) 100v, @ 50Hz/60Hz, 8.5A
13