Cleaning Upholstery; Lubrication; Service; Storage - Hoover Ultra User Manual

46
Lift tool, and position it against riser.
46
Pull tool slowly over carpet without
pressing trigger (dry stroke).
It is best to alternate wet and dry strokes
as described above. End with more dry
strokes to aid in faster drying of carpet.
Overlap strokes by 1/2 inch to help pre-
vent streaking.
To avoid saturating carpet, do not use
more than 4 wet strokes over any one
area. Always end with dry strokes.
If additional cleaning is necessary, wait
until the carpet is completely dry before
using the tool again.
Empty recovery tank when the motor
sound becomes higher pitched and
there is a loss in suction (see "Automatic
shut-off", page 7)
48
For heavily soiled areas, it may be
48
necessary to repeat the cleaning
process. Make crisscrossing strokes to
the original pattern; overlap each pass.
Make no more than 2 passes with the
solution over any one area to prevent
over-wetting and damage to fabric.
If additional cleaning is necessary, wait
until the upholstery is completely dry
before using the tool again.
Empty recovery tank when the motor
sound becomes higher pitched and
there is a loss in suction (see "Automatic
shut-off", page 7).
When finished cleaning, follow "After
cleaning" instructions on page 9 and
"After using tool" instructions on page 11.
12
When finished cleaning, follow "After
cleaning" instructions on page 9 and
"After using tool" instructions on page 11.

Cleaning upholstery

and automobile
i n t e r i o r s
Read "Before you begin cleaning"
Instructions on page 9.
Be sure to check the cleaning code on
your upholstery. Use your HOOVER
'SteamVac'deep cleaner only on
upholstery marked "W"or "W/S".
Place handle in upright position.
Agitator brushes will not rotate while
handle Is In upright position.
Fill clean solution tank with HOOVER
Carpet/Upholstery Detergent according
to instructions on pages 7 and 8. Attach
tool to end of hose.
Do not point tools toward people or
pets.
Dry hands and plug deep cleaner into a
properly grounded outlet.
S t o r a g e
Before storing:
• Empty solution tank and rinse
thoroughly with clean water.
• Replace empty solution tank and
turn deep cleaner ON. Squeeze
trigger and push deep cleaner for-
ward and back several times to
expel any solution remaining in the
deep cleaner's system. (Do not use
deep cleaner on wood floors.)
• Empty recovery tank and rinse
thoroughly with clean water.
Allow brushes and underside of deep
cleaner to air dry thoroughly before
storing deep cleaner on a carpeted or
wood surface.
Do not store deep cleaner with a full
solution tank In place.

Lubrication

The motor Is equipped with bearings
which contain sufficient lubrication for
the life of the motor. The addition of lubri-
cant could cause damage. Do not add
lubricant to motor bearings.
47
Turn deep cleaner on.
Gently press the tool (A) or (B) onto
47
the fabric. Press the trigger and
slowly pull the nozzle over the fabric.
Overlap strokes by 1/2 inch to help pre-
vent streaking.
Make additional strokes without pressing
the trigger to remove more moisture.
To clean in corners or creases, lift the
tool one-half inch from the fabric and
press the solution trigger.
Vacuum up the solution with the tool
without pressing the trigger.

Service

To obtain approved HOOVER service
and genuine HOOVER parts, locate the
nearest Hoover Factory Service Center
or Authorized Hoover Warranty
Service Dealer (Depot) by:
• checking the Yellow Pages under
Vacuum Cleaners - Household" OR
• checking the list of Factory Service
Centers provided with this cleaner
OR -
• calling 1-800-944-9200 for an
automated referral of authorized
service outlet locations (U.S. only)
OR-
• checking the Service section of The
Hoover Company on-line at
www.hoover.com
Please do not send your cleaner to The
Hoover Company in North Canton for
service, this will only result in delay.
If further assistance Is needed, contact
The Hoover Company Consumer
Response Center, North Canton, Ohio
44720 Phone: 1-330-499-9499.
In Canada, contact Hoover Canada,
Burlington, Ontario L7R 4A8,
Phone: 1-800-263-6376.
Always identify your cleaner by the
complete model number when request-
ing information or ordering parts. (The
model number appears on the bottom of
the cleaner.)