IBM NetVista Hardware Maintenance Manual
Hardware maintenance manual (hmm) for netvista 2259 and 6049 systems.
Hide thumbs
Also See for NetVista:
- Hardware maintenance manual (211 pages) ,
- Hardware manual (135 pages) ,
- Guide utilisateur (124 pages)
Related Manuals for IBM NetVista
Summary of Contents for IBM NetVista
- Page 1 IBM NetVista Type 6049 and 2259 Refresh 1.1 IBM NetVista Type: 6049 and 2259 Hardware Maintenance Manual Version: HMM02 Version: HMM02 1 of 35...
-
Page 2: Safety Information
IBM NetVista Type 6049 and 2259 Refresh 1.1 Safety information DANGER Electrical current from power, telephone, and communication cables is hazardou To avoid a shock hazard: • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. -
Page 3: Lithium Battery Notice
IBM NetVista Type 6049 and 2259 Refresh 1.1 Lithium battery notice CAUTION: Danger of explosion if battery is incorrectly replaced. When replacing the battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. - Page 4 IBM NetVista Type 6049 and 2259 Refresh 1.1 CAUTION: Use of controls or adjustme nts or performance of procedures other than those specified herein might result in hazardous radiation exposure. Removing the covers of the CD-ROM drive or DVD-ROM drive could result in exposure to hazardous laser radiation.
-
Page 5: Getting Started
IBM NetVista Type 6049 and 2259 Refresh 1.1 Getting Started .Before you begin, have a Philips medium sized head screwdriver to begin. .Locate the 3 screws at the back of the case; use the screwdriver to loosen them. Version: HMM02... - Page 6 IBM NetVista Type 6049 and 2259 Refresh 1.1 .Using both hands, gently pull back the top cover as shown in the figure. Slide the cover up off the frame of the case. . For installing the mainboard, locate the three screws which secure the plate and remove it.
-
Page 7: Installing The Power Supply Fan
IBM NetVista Type 6049 and 2259 Refresh 1.1 Installing the Power Supply Fan .The power supply should be installed in the back of the chassis. This is to draw the air out of the inside of the case. Check the position of the power supply fan as shown in the figure. - Page 8 IBM NetVista Type 6049 and 2259 Refresh 1.1 Assembling the Mainboard .The plastic spacers provide extreme support in areas of high mechanical stress on your mainboard. Insert the plastic spacers in the 2 mounting holes as shown in the figure through the back of your mainboard.
- Page 9 IBM NetVista Type 6049 and 2259 Refresh 1.1 .Prepare the CPU, heatsink and the CPU cooling fan. 478 Pins ? Pentium 4 Pull the CPU socket-locking lever away from the socket to unhook it and raise the locking lever to the upright position.
- Page 10 IBM NetVista Type 6049 and 2259 Refresh 1.1 . Attach the CPU cooling fan on top of the heatsink. Snap the four retention legs of the cooling fan into place. . Lock both levers on top of the cooling fan to their opposite sides to secure the cooling fan on top of the heatsink.
-
Page 11: Installing The Memory Modules
IBM NetVista Type 6049 and 2259 Refresh 1.1 Installing the Memory Modules .Open the left and right levers of the slot. Then firmly slide the Memory Module into the DIMM slot. The DIMM slots are keyed with notches and the DIMMs are indicated with cut outs so that they can only be installed correctly. - Page 12 IBM NetVista Type 6049 and 2259 Refresh 1.1 .Place the mainboard over the mounting brackets. Then slide the mainboard into place as shown in the next figure. .Secure the mainboard into the mounting brackets with screws. Do not overtighten the screws. Gentle pressure is enough.
-
Page 13: Connecting The Power Supply
IBM NetVista Type 6049 and 2259 Refresh 1.1 Connecting the Power Supply .After you have installed the mainboard into the case, you should connect the power cable from the case power supply unit to the mainboard power connector. Since the floppy drive is situated closely to the power supply. - Page 14 IBM NetVista Type 6049 and 2259 Refresh 1.1 . The power connector should fit perfectly in the slot on the ma inboard. Note the orientation of the cables before trying to connect them. Each function of the cable is already defined.
- Page 15 IBM NetVista Type 6049 and 2259 Refresh 1.1 . The storage bay should slide easily back to place. . Secure the chassis and the storage bay with screws. Do not over tighten the screws. Gentle pressure is enough. Version: HMM02...
- Page 16 IBM NetVista Type 6049 and 2259 Refresh 1.1 Installing the CD-ROM, Floppy and Hard Drives . There are two different size "bays" into which each of the various drives will fit. Take a close look at the drive and determine which is the “bay” for the floppy drive.
- Page 17 IBM NetVista Type 6049 and 2259 Refresh 1.1 .For the hard disk drive, follow the same manner for installing the floppy disk drive. Always secure the screws when installing the drives. This will prevent them from moving and falling from the storage bay.
- Page 18 IBM NetVista Type 6049 and 2259 Refresh 1.1 .For the CD-ROM drive, gently open the door panel. . Slide the CD-ROM drive into the bay and align the drive's faceplate with the front of the case. . When the CD-ROM drive is positioned correctly, secure the drive to the bay using four screws.
- Page 19 IBM NetVista Type 6049 and 2259 Refresh 1.1 .Close the door panel. This completes the setup for the CD-ROM drive. .Next, you should get familiar with the cables that are used with the various drives. The first cable is use for the...
- Page 20 IBM NetVista Type 6049 and 2259 Refresh 1.1 .Connect the other end of the cable to the CD-ROM drive. Note the orientation of the cable before trying to connect it. . Next, plug the hard disk cable into the Secondary IDE channel on the mainboard.
- Page 21 IBM NetVista Type 6049 and 2259 Refresh 1.1 .Lastly, connect the cables of the floppy drive as you did with the CD-ROM and hard disk drive. The edge of the cable that is yellow should situate firmly on the plastic shroud.
- Page 22 IBM NetVista Type 6049 and 2259 Refresh 1.1 .Attach the other end of the cable to the controller on the mainboard. See figure for reference. .Then attach the other end of the cable to the CD-ROM drive audio port. This completes the installation for the CD-ROM, Floppy and Hard drive.
- Page 23 IBM NetVista Type 6049 and 2259 Refresh 1.1 Connecting the Power LED . Connect the Power LED and Power SW cable on the Panel 1 of the mainboard. The Power button located in front of the case only works when the Power Switch connector is connected to the mainboard.
- Page 24 IBM NetVista Type 6049 and 2259 Refresh 1.1 . Next, Connect the HDD LED into the connector of the mainboard. The HDD LED indicator has two pins with one of them marked positive. One of the wires from the HDD LED is usually red and goes on the positive pin.
-
Page 25: Installing The Usb Cable
IBM NetVista Type 6049 and 2259 Refresh 1.1 Installing the USB Cable . This is the real side of the Dragon system. . Remove the dust cover from the COM port as shown in the figure. . The figure shows the system board inside the case. - Page 26 IBM NetVista Type 6049 and 2259 Refresh 1.1 . Remove one screw from the USB bracket using a screwdriver. . Then, loosen the screw on the other side. . Place the USB cable behind the port. . Attached the bracket and USB cable to the USB port.
- Page 27 IBM NetVista Type 6049 and 2259 Refresh 1.1 . Using the screwdriver, gently tighten the screws. . Following the same procedure in step 8. Attached the other USB cable to the USB port . Secure the USB cable with the screw.
- Page 28 IBM NetVista Type 6049 and 2259 Refresh 1.1 . This completes the installation for the USB cable. . The figure shows the USB connector. . Locate the USB2 header on the system board. . Connect the USB connector into the USB2 header of the system board.
- Page 29 IBM NetVista Type 6049 and 2259 Refresh 1.1 . The USB should look like this after it is connected. . To reduce unnecessary tangles, place the cables beside the slots as shown in the figure. . Install the AGP card back to the expansion slot.
-
Page 30: Installing The Expansion Card
IBM NetVista Type 6049 and 2259 Refresh 1.1 Installing the Expansion Card .The most commonly used expansion card is the AGP and modem card. Let’s start by installing the AGP card first. Remove the dust cover from the slot in the system case that corresponds t o the expansion slot that you going to use. - Page 31 IBM NetVista Type 6049 and 2259 Refresh 1.1 .Secure the AGP card with the screw. .Next, install the Modem card as the same way with the AGP card. Insert the Modem card to the first 32-bit PCI slot. Refer to the figure for reference.
- Page 32 IBM NetVista Type 6049 and 2259 Refresh 1.1 You have finished installing the Modem and AGP cards. Make sure that the add-on cards are installed properly on the mainboard See figure for reference. Version: HMM02 32 of 35...
-
Page 33: Completing The Assembly
IBM NetVista Type 6049 and 2259 Refresh 1.1 Completing the Assembly .When all necessary peripherals and drivers are installed in the case and that there are no loose wires that may get in the way of the CPU fan and other components. -
Page 34: Fru List
IBM NetVista Type 6049 and 2259 Refresh 1.1 FRU list Items IBM P/N FRU P/N Region Comments Recovery CDs 46P6851 Windows XP Home Simplified Chinese 46P6852 Windows XP Home Traditional Chinese 46P6853 Windows XP Home Hong Kong 46P6854 Windows XP Home AP English... - Page 35 IBM NetVista Type 6049 and 2259 Refresh 1.1 19K2964 19K2965 Hong Kong 56K PCI MODEM CARD/ GVC F-1156IV/R9C 19K2964 19K2965 Taiwan 56K PCI MODEM CARD/GVC F - 1156IV/R9C 19K2962 19K2963 ASEAN 56K PCI MODEM CARD/GVC F1156IV+/R9C Phone Cable 00K8182 00K8182...