Customizing The Equalizer Curve -Eq3; Adjusting Setup Items - Set - Sony MEX-BT2900 Operating Instructions Manual

Adjusting setup items - SET
Repeat steps 3 and 4 to adjust the equalizer
curve.
To restore the factory-set equalizer curve,
press and hold the select button before the
setting is complete.
S
Press
~
(BACK).
The setting is complete and the display
returns to normal reception/play mode.
Tip
Other equalizer types are also adjustable.
Customizing the equalizer curve
-EQ3
"CUSTOM" of EQ3 allows you to make your
own equalizer settings.
1
Select a source, then press the select
button repeatedly to select "EQ3."
2
Rotate the control dial to select
"CUSTOM."
3
Press the select button repeatedly
until "LOW," "MID" or "HI" appears.
4
Rotate the control dial to adjust the
selected item.
The volume level is adjustable in 1 dB steps,
from -10 dB to +10 dB.
1
Press and hold the select button.
The setup display appears.
2
Rotate the control dial until the
desired item appears, then press it.
3
Rotate the control dial to select the
setting, then press it. *
The setting is complete.
4
Press
~
(BACK).
The display returns to normal reception/play
mode.
*
For CLOCK-ADJ and BTM settings, step 4 is not
necessary.
Note
Displayed items will differ, depending on the source
and setting.
The following items can be set (follow the page
reference for details):
•
MONO*2 (Monaural Mode)
Selects monaural reception mode to improve
poor FM reception: "ON," "OFF."
BTM (page 15)
LOUDNESS
Reinforces bass and treble for clear sound at low
volume levels: "ON," "OFE"
AUX-A*1 (AUX Audio)
Activates the AUX source display: "ON,"
"OFF" (page 24).
BEEP
Activates the beep sound: "ON," "OFE"
DIMMER
Changes the display brightness: "ON," "OFE"
AUTO SCR (Auto Scroll)
Scrolls long items automatically: "ON," "OFE"
LOCAL (Local Seek Mode)
- "ON": to only tune into stations with stronger
signals.
- "OFF": to tune normal reception.
LPF*3 (Low Pass Filter)
Selects the subwoofer cut-off frequency: "OFF,"
"80Hz," "100Hz," "120Hz," "140Hz," "160Hz."
SW PHASE*3 (Subwoofer Phase)
Selects the subwoofer phase: "NORM," "REY."
HPF (High Pass Filter)
Selects the front/rear speaker cut-off frequency:
"OFF," "80Hz," "100Hz," "120Hz," "140Hz,"
"160Hz."
AUTO OFF
Shuts off automatically after a desired time
when the unit is turned off: "NO," "30S
(Seconds)," "30M (Minutes)," "60M (Minutes)."
REARlSUB*1
Switches the audio output: "SUB-OUT"
(subwoofer), "REAR-OUT" (power amplifier).
DEMO (Demonstration)
Activates the demonstration: "ON," "OFE"
AUTO ANS*1 (Auto Answer)
Answers an incoming call automatically.
- "OFF": to not answer automatically until
\. (handsfree ) is pressed.
-" 1": to answer automatically after 3 seconds.
- "2": to answer automatically after 10 seconds.
RINGTONE*1
Uses the ringtone of this unit or the connected
cellular phone: "1 (this unit)," "2 (cellular
phone)."
BT INIT*1 (Bluetooth Initialize) (page 22)
,-' " 0
rf
"f~" ~~.~~;
5dl
I n i l
La
LJ ~v
CLOCK-ADJ (Clock Adjust) (page 7)
CT (Clock Time)
Activates the CT function: "ON," "OFF"
(page 15, 16).
*
1 When the unit is turned off.
*2 When FM is received.
*3 When the audio output is set to "SUB-OUT."
23