Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gigabyte GS-SR 125E
Summary of Contents for Gigabyte GS-SR 125E
- Page 1 GS-SR 125E Rack Mount Server System Installation Guide...
-
Page 3: Table Of Contents
GS-SR125E System Installation Guide Contents SAFE, CARE AND REGULATORY INFORMATION.......1 PREFACE......................6 INTRODUCTION...................7 3.1. SCSI M ................7 EATURE OF ODEL CONTENTS PACKAGE................10 4.1. SCSI M .........10 OMPONENT ONTENT ODEL SYSTEM INSTALLATION PROCEDURES ........11 5.2..................11 HASSIS EMOVAL 5.3. CPU I ...................12 NSTALLATION 5.4. - Page 4 GS-SR125E System Installation Guide The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information contained herein. Third-party brands and names are the property of their respective owners.
-
Page 5: Safe, Care And Regulatory Information
GS-SR125E System Installation Guide 1. Safe, Care and Regulatory Information Important safety information Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. The product should be operated only from the type of power source indicated on the rating label. - Page 6 GS-SR125E System Installation Guide Precautions for Products With Laser Devices Observe the following precautions for laser devices: Do not open the CD-ROM drive, make adjustments, or perform procedures on a laser device other than those specified in the product’s documentation. Only authorized service technicians should repair laser devices.
- Page 7 GS-SR125E System Installation Guide generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
- Page 8 GS-SR125E System Installation Guide The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part 68, Sec. 68.381 (c) (3)). / for Canadian users only / Canadian Department of Communications Compliance Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of Industry Canada.
- Page 9 GS-SR125E System Installation Guide metallic water pipe system, if resent are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading.
-
Page 10: Preface
For your protection, please read and understand all of the safety and operating instructions regarding your Gigabyte Server and retain for future reference. The procedures in this guidebook assume that you are a system or network administrator experienced in installing similar hardware. -
Page 11: Introduction
GS-SR125E System Installation Guide 3. Introduction Welcome to the Gigabyte GS-S R125E Rack mount Server System Installation Guide. The guidebook provides instructions for configuration hardware for the GS-SR125E to your system. In order to get the optimal usage of your server, please pay... - Page 12 GS-SR125E System Installation Guide Features Description Motherboard GA-8IPP533 Processor Supported Support Dual Intel XEON Prestonia processors up tp 3.06 GHz+ FSB 400/533Mhz BIOS AMI BIOS with enhanced ACPI feature for PC99/Win98/ME/2000 compliance; Green, PnP, DMI, INT13 & Anti-Virus functions IDE #0-#3, SCSI, LS120, ZIP, and CD-ROM bootable.
- Page 13 GS-SR125E System Installation Guide Intelligent Management Standard supports IPMI v System 1.5 for system monitoring. IPMI card: GC-HP12E-Q Hot Swap Hard Disk Drive Support 4 SCSI Ultra-320 Bays Hot-Swap HDD Mass Storage System Four low-profile shelves for hot-swappable drives One standard FDD drive (Optional device) One slim type CD-ROM drive...
-
Page 14: Contents Package
GS-SR125E System Installation Guide 4. Contents Package When opening the package, please ensure the system components are not damaged during the shipping. Using the following checklist to verify the contents. If any component is missing or damaged in the system, please contact your vendor immediately. -
Page 15: System Installation Procedures
GS-SR125E System Installation Guide 5. System Installation Procedures Please remove the protective thin films (Top and bottom) from the system when installing. 5.2. Chassis Removal Step 1. Push down the two buttons located at two sides of the chassis. (Fig-1) Figure 1 Figure 2 Step 2.. -
Page 16: Cpu Installation
GS-SR125E System Installation Guide 5.3. CPU Installation Step 1. Please make sure the CPU type and speed that are supported by the motherboard. Step 2. To Install the CPU(s), lift up the bar that located next to the socket. (Fig-3) Figure 3 Step 3. -
Page 17: Heat Sink Installation
GS-SR125E System Installation Guide Step 4. Then, align the CPU insert it into the socket. (Fig-5) Push the lever back to the original position. (Fig-6) Figure 5 Figure 6 5.4. Heat Sink Installation Step 1. Put the Heat sink on the CPU. (Fig-7) Figure 7 Figure 8 Step 2. -
Page 18: Memory Installation
GS-SR125E System Installation Guide Step 3. First, hook one end of the cooler bracket to the CPU socket as shown in the Fig-8. Make sure the middle part of bracket is push into the desired position. (Fig-8) Step 5. Hook the other end of the cooler bracket by gripping it to another side of retention module. -
Page 19: Pci Expansion Card Installation
GS-SR125E System Installation Guide 5.6. PCI Expansion Card Installation GS-SR125 provides expansion riser slots for two peripheral cards, 64Bit/66 MHz full-height. To install the peripheral, please go through the following steps. Step 1. There are screws holding the riser bracket. Remove the screw on the top of the bracket. - Page 20 GS-SR125E System Installation Guide Step 2. Installing the PCI Riser card. To install the riser card, just simply push it into the module. (Fig-14) Figure 14 Figure 15 Step 3. Secure the card with screws. (Fig-15) Step 4. Repeat Step 2 to install another card. (Fig-16) Step 5.
-
Page 21: Reinstall Top Cover
GS-SR125E System Installation Guide Figure 18 5.7. Reinstall Top Cover When complete the installation of the entire essential components (from subsection 5.1 to 5.7), replace the plastic air duct. This will secure the airflow is inside the chassis. Failure to do so may cause CPU and Memory over heating. -
Page 22: Scsi Id Setting (For Scsi Model Only)
GS-SR125E System Installation Guide 5.8. SCSI ID Setting (For SCSI Model ONLY) The SCSI ID is shown in Figure 20. If there occurs an abnormal SCSI hard disk drive behavior (e.g. does not detect the hard disk drive properly), please make sure that the each HDD has different Figure 20... - Page 23 GS-SR125E System Installation Guide Jumper Setting For HD1, HD2, and HD3 Jumper ON (Jumper Close): 1-2 OFF (Jumper Open): 2-3...
-
Page 24: Hard Disk Drive Installation
GS-SR125E System Installation Guide 5.9. Hard Disk Drive Installation Step 1. Pull the hard disk drive tray handle and remove the tray from the chassis (Fig-21). Insert the hard disk drive into the tray. Secure each hard disk drive with screws (Fig-22 to 24). Figure 21 Figure 22 Figure 23... - Page 25 GS-SR125E System Installation Guide Figure 25 Figure 26...
-
Page 26: Motherboard Layout & Jumper Setting
GS-SR125E System Installation Guide 5.10. Motherboard Layout & Jumper Setting Health LED ID LED/Switch... - Page 27 GS-SR125 Series System Installation Guide Jumper Setting Description: A: CRL_CMOS (Clear CMOS) 1-2 Close: Clear CMOS 2-3 Close: Normal (Default Value) B: JP8 (Onboard VGA Function) 1-2 Close: VGA Enabled (Default Value) 2-3 Close: Onboard VGA Disabled C: JP2 (BIOS Block Write Protect) 1-2 Close: BIOS Top Block Write Protect 2-3 Close: BIOS 2-8 Block Write Protect D: JP9 (Front USB Device Wake Up Function)
-
Page 28: Appearance Of Gs-Sr125E
GS-SR125E System Installation Guide 5.11. Appearance of GS-SR125E 5.11.1. Front View of GS-SR125E USB & LED SCSI Ultra-160 Hot-Swap HDD Manufacture Option: Floppy Disk/4th HDD tray 5.11.2. Rear View of GS-SR125E PS/2 Keyboard and Mouse connectors Full-Height/Full Length ID LED Button LAN1/2 Ports VGA Port Half-Length... -
Page 29: Led Indicator Description
GS-SR125 Series System Installation Guide 5.11.3. LED Indicator Description Acting Color Status Power LED Green Power On Amber Power cable plug-in Blink Green System stands by No power... - Page 30 GS-SR12E System Installation Guide SYS LED Amber System is ready but degraded: some CPU Fault, DIMM Killed Critical Power Modules Failure, Critical FANs Failure, Voltage (Power Supply), Critical Temperature and Voltage Non-critical temperature and voltage LAN LED Green LAN online LAN offline Blinking Green...
- Page 31 GS-SR125 Series System Installation Guide HDD LED: HDD LED 1 HDD LED 2 Acting Color Status HDD LED 1 HDD Idle HDD LED 1 Blink Green HDD Acting HDD LED 2 No error HDD LED 2 Faulty or rebuild stop Green Slow Blink Green HDD LED 2...
-
Page 32: Floppy Drive Installation (Optional)
GS-SR125E System Installation Guide 5.12. Floppy Drive Installation (Optional) Step 1. Remove three screws on the front top cover, (Fig-28) Push down the two buttons located at two sides of the system to remove front top cover. (Follow the arrow direction shown in Fig- Figure 27 Figure 28 Step 2. - Page 33 GS-SR125 Series System Installation Guide Step 3. Place the tray into chassis (Fig-32) and push the floppy disk drive tray handle to the closed position. Note: It will make “click” sound when the floppy disk drive is inserted properly Figure 31 Figure 32 Step 4.
-
Page 34: Connector Icon Description
GS-SR125E System Installation Guide 5.13. Connector Icon Description Suggested icons Description Keyboard Mouse Parallel Port Serial Port...