Starting A Ire Automatic; Aintaining The Ire; Relaxation Ode - Harman P35i Owner's Manual

P3 5 i F ireplace Insert
G . Starting a F ire - " AUTOMATIC"
1. With the mode selector in the O
the eed Ad uster NOT on Test , plug the power
cord into a properly grounded receptacle.
2. ill the hopper with RY fuel.
. Turn the EE A
run the feed motor for one minute. If you begin to
see fuel entering the burn pot, you can stop the
test cycle. Return to # or #5 to start out.
. Position the Igniter switch to AUTO ATIC.
5. Turn the mode selector dial to the desired mode.
This will start the combustion blower, feeder, and
igniter operating. If R oom Temp is selected, be
sure to turn the temperature dial above the
current room temperature.
. After the initial feed cycle is typically when you ll
begin to see sparks, smoke, or flames.
K eep Hopper Lid, Ash Pan, and F ire viewing doors
closed while in operation. Maintain all door seals
and gaskets in good condition. R eplace gaskets
when necessary using parts obtained through
your Harman® dealer.
H. Maintaining the F ire
Once the istribution Blower begins operation, your
fire is well established. Now, you can make any desired
ad ustments to the temperature dial. Remember, in
STO E TE P, the temperature dial uses the inner
portion of the scale (#1 thru 7). In ROO TE P, select
the desired temperature in ahrenheit from 50 to 0
degrees.
The flames should appear brisk and bright. If you see
deep orange and lazy flames, it is usually an indication
that the burn pot needs to be cleaned. Refer to the
aintenance Section of this manual.
Warning! risK of fire!
materials, gasoline, and other flammable vapors or
liquids clear of this appliance.
• o NOT store flammable materials in the vicinity
of this appliance.
• O NOT BURN GARBAGE OR
LUI S SUCH AS GASOLINE, NAPTHA OR
ENGINE OIL.
• O NOT USE CHE ICALS OR
START A IRE.
Keep all such liquids well away from the heater while it
is in use, combustible materials may ignite!
S a v e T h e s e I n s t r u c t i o n s
position, and
USTER dial to Test . This will
eep combustible
LA
LUI S TO
I. R elax ation Mode
An added feature for those times when you d like to
unwind watching a fire but yet do not want all the heat.
With the igniter switch in the
the mode selector in STO E TE P , your temperature
dial can be set up to a # and the distribution blower
will be disabled. As you turn up the temperature dial
and the fire begins to burn hotter, the distribution
blower will begin to operate.
J . Shut-Down
uring operation in ROO TE P AUTO ATIC mode,
the appliance will shut down naturally when demand is
met or exceeded. In other modes of operation, the unit
will shut-down only if or when it runs out of fuel.
To kill or stop a fire, turn the mode selector dial to
O . The shut down cycle will slow or stop the
feeder to gradually cool the fire and ensure that all of
the exhaust gases are safely expelled before stopping
the combustion blower. This not only ensures removal
of all smoke and gases, it also keeps the fire from
attempting to travel into the fuel storage hopper. or this
reason Hearth
installing a battery back-up in areas where frequent
ABLE
power outages are experienced. (Also see page1 )
NEV ER ATTEMPT TO K ILL A F IR E BY
THE PLUG
THE ELECTR ICITY SUPPLY .
The best way to kill a fire, especially at the end of the
heating season, is to simply allow it to run out of fuel.
3-90-775R16_08/13
ANUAL position and
Home Technologies recommends
OR OTHER W ISE DISCONNECTING
P e l l e t s o r C o r n /P e l l e t M i x t u r e O n l y
PULLING
27