Harman P35i Owner's Manual page 26

D. Before Y our F irst F ire
• Be sure the appliance is installed properly and
that all safety requirements have been met.
Pay particular attention to the clearances to
combustibles, floor protection and the venting
instructions.
• Test your smoke detector(s) and CO detector(s) to
the specifications of the manufacturer.
• ouble check that the ash pan and internal firebox
are empty.
• Be sure to read this entire manual.
E. Draft Test Procedure
• Using a 1 wrench, remove the draft test port
plug bolt, located to the left inside the firebox. This
bolt threads downward through the outside of the
body. Externally, the opened hole is located above
the ash pan spring latch on the left.
• Insert
the draft
meter
hose into
the test
port.
• Be sure
the meter
is capable
of a scale
between 0
and 1 inch
Water
Column.
ero the meter if necessary, and be sure it is set
up to read in negative pressure.
• Be sure the ash pan, door, and hopper lid are all
closed and latched.
• Turn the feed ad uster to Test mode.
• uring the first minute of test, the combustion
blower will be on high. Record the high draft
reading here
should be above -0.5 W.C. but no higher than -1
W.C.
• After a minute, the combustion blower will go
to low speed. Here you want to see a reading
between -0. 0 and -0. 5 . If necessary, ad ust the
draft voltage using the low draft ad ustment screw
on the circuit board (See Page 2 ). Clockwise
will increase the draft and counter-clockwise will
decrease it.
• Once set, record
here:
• Be sure and turn off of Test mode.
the meter and return the plug bolt to the test port.
2
P e l l e t s o r C o r n /P e l l e t M i x t u r e O n l y
-W.C. The high draft
the low draft
-W.C.
isconnect
F . Starting a F ire - " MANUAL"
1. With the mode selector in the O
the eed Ad uster NOT on Test , plug the power
cord into a properly grounded receptacle.
2. ill the hopper with RY fuel.
. Turn the EE A
run the feed motor for one minute. If you begin to
see fuel entering the burn pot, you can stop the
test cycle. Return to # or #5 to start out.
. Turn the mode selector dial to the desired mode.
This will start the combustion blower operating.
If R oom Temp is selected, be sure to turn
the temperature dial above the current room
temperature.
5. ill the burn pot with a mixture of wood pellets and
starting gel.
. Light the starting gel with a match, and close the
door.
7. Only after the ESP temperature increases, will the
feeder start operating to increase the fire size.
NEV ER APPLY
THE BUR N POT W ITHOUT THE COMBUSTION
BLOW ER OPER ATING .
TESTED AND APPR OV ED F OR
PELLETS OR
PELLETS ONLY . USE OF ANY OTHER TY PE OF F UEL
W ILL V OID THE APPLIANCE W AR R ANTY .
The optimal method of operation is in R oom Temp
mode, with the Ignition switch set to Automatic.
reading
- 0-775R1 08 1
P3 5 i F ireplace Insert
USTER dial to Test . This will
STAR TING G EL TO THE F UEL IN
W AR NING
USE W ITH W OOD
A MIX TUR E OF SHELLED COR N AND
W AR NING
" NEV ER USE G ASOLINE, G ASOLINE-TY PE
LANTER N F UEL, K ER OSENE, CHAR COAL
LIG HTER F LUID, OR SIMILAR LIQ UIDS TO
STAR T OR " F R ESHEN UP " A F IR E IN THIS
HEATER . K EEP ALL SUCH LIQ UIDS W ELL
AW AY F R OM THE HEATER W HILE IN USE" .
position, and
S a v e T h e s e I n s t r u c t i o n s