Simulator; Units; Language; Section 2: Maintenance And Warranty - Humminbird Legend 1000 Operating Instructions Manual

MAINTENANCE AND WARRANTY
CONTROL PANELS / MAINTENANCE/TROUBLESHOOTING

Simulator

allows the
S L
IMULATOR EGEND
to operate in simulated
S
ERIES
sonar mode. This is useful for
learning the features and functionality of the
when not on the water. Settings to Control
S
ERIES
Panels that are retained in normal operation will be
retained in Simulator Mode if a transducer is
connected. When operating with the Simulator on and
without a transducer connected, the Legend 1000
Series does not remember any changes to settings.
The Simulator setting defaults to factory settings after the
Legend 1000 Series is turned off.

Units

selects the units of
U
NITS
measure for boat speed.
Selecting displays the
KTS
speed in nautical miles per hours;
speed in miles per hour.
measure for boat speed and depth in one of two
combinations supported by every
• displays depth in feet and speed in miles
F /MPH
EET
per hour.
• depth in feet and speed in nautical
F /KTS
EET DISPLAYS
miles per hour.
also selects the units of measure for boat speed
U
NITS
and depth in one of four additional combinations
supported by the International Models only:
• displays depth in metres/speed in
M /KPH
ETRES
kilometres per hour.
• displays depth in metres/speed in nautical
M /KTS
ETRES
miles per hour.
• displays depth in fathoms/speed in
F /KTS
ATHOMS
nautical miles per hour.
• displays depth in fathoms/speed in
F /KPH
ATHOMS
kilometres per hour.
The settings are retained in memory after the unit is
U
NITS
turned off.
12
1000
L
EGEND
displays the
MPH
selects the units of
U
NITS
L 1000 S
EGEND ERIES

Language

(International Models
L
ANGUAGE
only) selects the language for
text used in the
and for messages. See the
1000
Specifications for included languages.
L setting is retained in memory after the L
ANGUAGE
is turned off. The factory setting is E

MAINTENANCE

Your
L 1000 S
EGEND
trouble-free operation with virtually no maintenance.
Follow these simple procedures to ensure your
continues to deliver top performance.
1000 S
ERIES
Cleaning
If the unit comes into contact with salt spray, simply
wipe the affected surfaces with a cloth dampened in
fresh water. Do not use a chemical glass cleaner on the
lens, as chemicals in the solution may crack the lens.
When cleaning the LCD protective lens, use a
:
chamois and non-abrasive, mild cleaner. Do not wipe
while dirt or grease is on the lens. Be careful to avoid
scratching the lens.
If your boat remains in the water for long periods of
time, algae and other marine growth can reduce the
effectiveness of the transducer. Periodically clean the
face of the transducer with liquid detergent. Pivoting
the transducer up in the bracket may allow better
access for inspection or cleaning.
Wetting the Transducer
If your boat remains out of the water for a long period
of time, it may take some time to wet the transducer
when returned to the water. Small air bubbles can
cling to the surface of the transducer and interfere
with proper operation. These bubbles dissipate with
time, or you can wipe the face of the transducer with
your fingers after the transducer is in the water.
Heat Damage
Never leave the
trunk—the extremely high temperatures generated in
hot weather can damage the electronics.
C P
ONTROL ANELS
L 1005/1005 D
EGEND
EGEND
.
NGLISH
is designed to provide years of
ERIES
in a closed car or
L 1000 S
EGEND ERIES
EEP
1005 /1005 D
EEP
L
EGEND