Electrolux Diva Service Manual page 31

6.11 Customer function / setting of water hardness
General information
w Setting and changing the water hardness area is executed in
all designs resp. key arrangements analogously.
w For that you always have to use the keys S0, S1, S2 and S3
independent of their variant-depending program load.
w Key S1 is ALWAYS the "water hardness area key"
w The water hardness area value 4 is preset by the manufacturer.
With setting "1L" it is generally not regenerated.
A salt addiition is not necessary.
w A possible existing "salt" LED is not selected.
Electronic and mechanical setting with the appliance:
w Next to the "electronic" setting on the control panel described
at the right you also have to pay attention to the mechanical
setting in the appliance by the 2-step blending switch.
(see for that the table for hardness area values)
LD1 S1
1 99
Tastenanordnung
LD2 S2
waagrecht
LD3 S3
LD1 LD2 LD3
1 99
Tastenanordnung
senkrecht
S1 S2 S3
Table for hardness area values:
Anzeige Anzeige Einstellung der
Härtestufe
Display Ende-LED
Anzahl blinken elektr.. mech. in dH
1L 1 mal bis
1
2L 2 mal 2 4 bis 10
3L 3 mal 3 11 bis 14
0
4L 4 mal 4 15 bis 18
5L 5 mal 19 bis 22
5
6L 6 mal 6 23 bis 28
7L 7 mal 7 29 bis 36
8L 8 mal 37 bis 42
8
1
9L 9 mal 43 bis 50
9
10L 10 mal 10 51 bis 70
Calling / changing / saving the "electronic" hardness area value
blending
LD0
switch
S1
LD0
S0
LD1
LD2
Wasserhärte Bemerkung
LD3
in mmol/L Bereich
4 bis 0,7 I
kein Regenerieren
... AUS nach 60sek. automatisch
0,7 bis 1,8 I / II
1,9 bis 2,5 II
2,6 bis 3,2
III
3,3 bis 3,9
4,0 bis 5,0
5,1 bis 6,4
6,5 bis 7,5 IV
7,6 bis 8,9
9,0 bis 12,5 doppelt Regenerieren
1.
LD1 S1
LD2 S2
LD3 S3
blinken
2.
LD1
S2
LD2
LD3
S3
blinken
3.
LD1
4L
S1
blinken
LD1
5L
S1
6L
Pro
Tastendruck
10L
+ 1 Stunde
1L
2L
blinken
4.
LD1 S1
2L
LD2 S2
LD3 S3
LD0
S1
S2
S3
S1
LD1 S1
LD2 S2
LD3 S3
... AUS durch manuelle Betätigung über Ein/Aus
31
When calling the customer functions, generally no
washing cycle must be selected!
Calling the function "set water hardness"
LD0
Switch on appliance by ON/OFF key S0.
1.
S0
2. Press keys S2 and S3 simultaneously until the
LD0
confirmation LEDs LD1, LD2 and LD3 are flashing.
S0
3. By actuating the function key S1 you now can call the
LD0
water hardness function. The confirmation LED LD1
continues flashing, LEDs LD2 and LD3 go out.
The set hardness area is indicated in the display
S0
(see for that the table on the left side of this page!)
Changing the set hardness
Any other actuation of the function key S1 changes
the hardness area. This increases the value scrolling.
( 4L - 5L - 6L - ... - 10L - 1L - 2L - ... )
LD0
Leaving the function
S0
4. After pressing the function key S1 last you can leave
the special program as follows.
After 60 seconds all displays go out automatically,
except LD0 of the ON/OFF key
or
the appliance is switched off by the ON/OFF key S0.
Saving the set water hardness
LD0
The selected hardness area is saved directly
S0
after any entry.