Electrolux Diva EDW 1500 Service Manual
Hide thumbs
Also See for Diva EDW 1500:
- Service manual (56 pages) ,
- Service manual (40 pages) ,
- Service manual (37 pages)
Related Manuals for Electrolux Diva EDW 1500
Summary of Contents for Electrolux Diva EDW 1500
- Page 1 All manuals and user guides at all-guides.com SERVICE MANUAL DISHWASHER EDW 1500 599 515 015 EDW 1500...
- Page 2 All manuals and user guides at all-guides.com Index...
- Page 3 All manuals and user guides at all-guides.com Display Door handle Control lamps Progamme buttons On/Off button * Appliances with height-adjustable feet Plinth height for appliances 820 mm high 100 - 175 mm Plinth height for appliances 870 mm high 150 - 230 mm...
- Page 4 All manuals and user guides at all-guides.com 3. Components...
- Page 5 All manuals and user guides at all-guides.com display „lack of rinse aid“ dosing of rinse-aid maximum filling level outlet of rinse-aid detergent tray detergent tray for pre wash Spule Zeit Zeit Zeit Zeit Zeit Zeit...
- Page 6 All manuals and user guides at all-guides.com Temp. Widerstand 10°C 9653 Ohm 25°C 4843 Ohm 60°C 1204 Ohm 90°C 445 Ohm...
- Page 7 All manuals and user guides at all-guides.com...
- Page 8 All manuals and user guides at all-guides.com...
-
Page 9: Service Tips
All manuals and user guides at all-guides.com 4. Service tips Torx... - Page 10 All manuals and user guides at all-guides.com...
- Page 11 All manuals and user guides at all-guides.com...
- Page 12 All manuals and user guides at all-guides.com...
-
Page 13: Water Course Scheme
All manuals and user guides at all-guides.com 5. Water Course Scheme Inlet valve Flow heater Non-return valve salt container Air break Drain pump Regeneration valve Regeneration water dosage Non-return valve Safety inlet hose Overflow safety level Spray arms Base tray Safety overflow Roof-mounted shower Float switch... - Page 14 All manuals and user guides at all-guides.com 5.1 All-Around Water Protection Aqua-Control Inlet Hose The inlet hose has a double-wall construction. The inner hose is equipped with a flow restrictor built into the tap connection, and has a flow rate of 4 litres per minute. The inlet valve (1) is located in the base of the dishwasher.
-
Page 15: Water Inlet
All manuals and user guides at all-guides.com 5.2 Water Inlet The water flows into the regeneration dosage chamber (7) via inlet valve (1), over air break (2), into regeneration dosage chambers (3) into softener (8). At this point the water divides. 1/4 of the water enters the tub through the vent (23). - Page 16 All manuals and user guides at all-guides.com s tatic water dynamic water max. 4 load load r epetitions to level with level contr ol T imeout 1 T imeout 2 speed target- speed ˜ 10 S ek. 5 S ek. 5 S ek.
- Page 17 All manuals and user guides at all-guides.com speed 2800 var iable s peed 1600 20 S ec. high,r high,r high,r s tar t-r outine time in s ec. -function = time (high s peed) + r andom time high,r water in L dynamic pulse was h...
- Page 18 All manuals and user guides at all-guides.com 5.3 Draining During the wash cycle the water is pumped out at various stages. First the draining water cleans the filters (16). The filters are open at the bottom which allows any soilage to be rinsed off sufficiently. There is a non-return valve (20) at the inlet connection to the drain pump (19).
- Page 19 All manuals and user guides at all-guides.com dr ain pump 1 dr aining s equence with var iable timing level check! (var iable) (var iable) (var iable) 'UDLQ &\FOH )LUVW GUDLQLQJ EHIRUH HYHU\ ZDVK F\FOH VHF VHF VHF 'UDLQLQJ DIWHU WKH ZDVK F\FOHV VHF VHF...
- Page 20 All manuals and user guides at all-guides.com 6.1 Inputs and outputs: keys, LEDs and lamps Arrangement and designation with vertical key arrangement Display LD13 - 28 ON/OFF switch LD29 LD10 LD11 lamp on/off LD12 S.No. 111 59 32-... among others for DGN appliances with AEG design with horizontal key arrangement Display LD13 - 28 LD4 LD5...
-
Page 21: General Information
All manuals and user guides at all-guides.com 6.2 General information Equipment in the panel area (see description page B 1) Possible equipment w Separate ON/OFF switch S0 without optical confirmation w 6 keys S1 to S6 to select programs or options with the corresponding LEDs All keys are free and can be programmed without any restriction by the programming of the appliance variant. - Page 22 All manuals and user guides at all-guides.com 6.3 Input philosophy: program selection Tastenano senkre 1 99 1. Appliance in switched-off condition 2. Switch on appliance with ON/OFF key S0 Ä Display LD0 with ON/OFF key is lit. Ä Appliance is in the prestart mode. Ä...
- Page 23 All manuals and user guides at all-guides.com Tastenanor senkrec 1 99 6.4 Input philosophy: select start time Variant A time preselection after program selection time ç variant A 1. Appliance in switched-off condition. 2. Switch on appliance by ON/OFF key S0 Ä...
- Page 24 All manuals and user guides at all-guides.com 6.5 Input philosophy: program run Cycle start 3 seconds after actuating any key last resp. after the adjusted start time has run down, the selected washing cycle will start automatically. A time preselection resp. a program option cannot be selected any more additionally from that moment.
- Page 25 All manuals and user guides at all-guides.com Taste 6.6 Input philosophy: delete program A selected or already started washing cycle can be deleted at any time during normal operation. Delete program (using the reset function) Reset function always with the key S2 and S3. Laufzeit 1.
- Page 26 All manuals and user guides at all-guides.com Tastenano 6.7.1 Input philosophy: alter program senkre 1 99 Alter program during the prestart phase Display blinkt 1. Program has been selected but did not yet start Laufzeit Ä Display LD0 with ON/OFF key, program LED and run time Ä...
- Page 27 All manuals and user guides at all-guides.com 6.7.2 Input philosophy: alter program Tastenan senk Alter program after successful cycle start 1. Cycle running Laufzeit Ä Display LD0 with ON/OFF key, corresponding progr Ä Run time is indicated in the display. 3 Sekunden betätigen 2.
- Page 28 All manuals and user guides at all-guides.com 6.8 Input philosophy- interrupt program Interrupt program By using the ON/OFF key S0 it is possible to interrupt the program as long as one wants. The same is valid for an interruption by opening the door. There is no deleting function integrated in the ON/OFF key S0! If the cycle is interrupted by using the ON/OFF key, all displays go out.
- Page 29 All manuals and user guides at all-guides.com 6.9 Input philosophy - displays All displays are designed as LED displays and are available depending on the appliance variant. Start-time preselection and run time are indicated via a display. Displays for program selection and option Ä...
- Page 30 All manuals and user guides at all-guides.com 6.10 Short survey of all customer, service and aftersales ser Tastenanordnung senkrecht Tastenanordnun 1 99 1 99 S2 S3 S4 S5 S6 Confirmatio Who? Which function? Selection of special mode customer or service of the special m simultaneously ...
- Page 31 All manuals and user guides at all-guides.com 6.11 Customer function / setting of water hardness General information Calling / changing / saving the "electronic" hardness w Setting and changing the water hardness area is executed in Calling the fu all designs resp. key arrangements analogously. w For that you always have to use the keys S0, S1, S2 and S3 Switch independent of their variant-depending program load.
- Page 32 All manuals and user guides at all-guides.com 6.12 Customer function / deactivation of rinse-aid addition General information Calling / changing / saving the rinse-aid addition dea Calling the fu The function rinse-aid deactivation does not exist generally and must be programmed in the software variant. Switch w The deactivation resp.
- Page 33 All manuals and user guides at all-guides.com 6.13 Customer function / deactivation of signal sound: General information Calling / changing / saving the signal sound deactiva Calling the fu The function deactivation of the signal sound does not exist generally and must be programmed in the software Switch variant.
- Page 34 All manuals and user guides at all-guides.com 7.1 Service function / readout of fault memory and single actua General information Calling above-mentioned service function w Calling the service functions is executed in all designs Calling the functi "readout of fau resp.
- Page 35 All manuals and user guides at all-guides.com 7.2 Service function / LED test with integrated deletion of the General information Calling above-mentioned service function w Calling the service functions is executed in all designs Calling the func resp. key arrangements analogously. "LED test wit w For that you always have to use keys S0, S1, S2 and S3 Press ke...
- Page 36 All manuals and user guides at all-guides.com 7.3 Service function / manufacturing test routine: General information Calling above-mentioned service function w Calling the service functions is executed in all designs Calling the func resp. key arrangements analogously. w For that you always have to use keys S0, S1, S2 and S3 Press ke independent of their variant-depending program load.
- Page 37 All manuals and user guides at all-guides.com Overview Errors Displayed Applicable for EDW1500 / 1503 (VGA) -- EDW11 Display Display Error Display Call Acoustic Error Output via Short Explanation visible for Error Memory Indication Name Indicator Lamp Screen END LED Customer** (Service) No.of Beeps...
- Page 38 All manuals and user guides at all-guides.com List of Possible Error Causes Possible error causes Code Water tap is closed or faulty No water pressure, pressure too low or changing Screen in front of inlet valve clogged Flow governor at inlet valve faulty No or not enough water let in Inlet valve faulty Inlet valve deenergized (faulty wiring or no activation by electronics)
- Page 39 All manuals and user guides at all-guides.com 9. Wirings...
- Page 40 All manuals and user guides at all-guides.com...