Grandstream Networks HT701 User Manual page 26

Preferred DTMF method
Disable DTMF
Negotiation
Send Flash Event
Enable Call Features
Offhook Auto-Dial
Proxy-Require
Use NAT IP
Distinctive Ring Tone
Disable Call Waiting
Disable Call-Waiting
Caller ID
Disable Call Waiting
Tone
Disable Receiver
Offhook Tone
Disable Reminder Ring
for On-Hold Call
Disable Visual MWI
Ring Timeout
Hunting Group Ring
Timeout
Hunting Group Type
Delayed Call Forward
Wait Time
Grandstream Networks, Inc.
VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
The HT70X supports up to 3 different DTMF methods including in-audio, via RTP
(RFC2833) and via Sip Info using SIP INFO messages. The user can configure DTMF
method in a priority list.
Default is No. If set to yes, use above DTMF order without negotiation
Default is No. If set to yes, flash will be sent as DTMF event.
Default is Yes. (If Yes, call features using star codes will be supported locally)
This parameter allows users to configure a User ID or extension number that is
automatically dialed when off-hook. Only the user part of a SIP address needs to be
entered here. The HT70X will automatically append the "@" and the host portion of the
corresponding SIP address. HT701 and HT702 only
SIP Extension to notify SIP server that the unit is behind the NAT/Firewall.
NAT IP address used in SIP/SDP message. Default is blank.
Custom Ring Tone 1 to 3 with associate Caller ID: when selected, if Caller ID is
configured, then the device will ONLY uses this ring tone when the incoming call is
from the Caller ID. System Ring Tone is used for all other calls. When selected but no
Caller ID is configured, the selected ring tone will be used for all incoming calls using
the FXS port or Profile. Distinctive ring tones can be configured not only for matching a
whole number, but also for matching prefixes. In this case symbol * (star) will be used.
For example:
if configured as *617, Ring Tone 1 will be used in case of call arrived from the area
code 617. Any other incoming call will ring using cadence defined in parameter System
Ring Cadence located under Advanced Settings Configuration page.
Note: If server supports Alert-Info header and standard ring tone set (Bellcore) or
distinctive ring tone 1-10 is specified, then the ring tone in the Alert-Info header from
server will be used. Bellcore rings and tones are independent from custom ring tones.
The custom ring tones can also be specified by alert-info header, for example
Alert-Info: <http://127.0.0.1>;info=ring5
Default is No. If set to YES Call Waiting indication information will not be provided to
analog phone connected to this FXS port.
Default is No. If set to YES Call Waiting caller ID will not be provided to analog phone
connected to this FXS port.
Default is No. This is to disable the stutter Call Waiting Tone when a Call Waiting
information arrives. The CWCID information will still be displayed.
Default is No. If set to yes, it will disable the warning to alert that the phone has been
left off-hook for an extended period of time.
Default is No. Do not play the reminder ring when this is set to Yes.
Default is No. If set to "Yes", the MWI information will not be transferred to the analog
phone connected to the FXS port.
Default value is 60 Sec. Incoming call will stop ringing when not picked up given a
specific period of time.
Default value is 20 Sec. If call is not answered within this designated time period, the
callwill be forwarded to the next member of a Hunt Group. HT704 only
Linear and Circular. Default is Circular. Linear style will sort the call to the lowest-
numbered available line, this is also called "serial hunting". Circular style will distribute
the calls "round-robin". If a call is assigned to line 1, the next call goes to 2 and the next
to 3. The succession throughout each of the lines continues even if one of the previous
lines becomes available. When the end of the hunt group is reached, the hunting starts
over at the firstline. Lines are skipped if they are still busy on a previous call. HT704
only
Default value is 20 seconds. In case this feature activated using * codes (*92 code),
the call will be forwarded after this preconfigured amount of time.
HT-70X User Manual
Firmware Version 1.0.0.18
Page 26 of 35
Last Updated: 03/2012