Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
NEW SAVONA 1.6 GPF ONE-PIECE TOILET
Model 2097.012
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure
your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Hacksaw
Wax Ring/Gasket
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must be as listed below:
FINISHED WALL
736mm
23mm
(7/8)
176mm
(7)
203mm
(8)
305mm
(12)
4
SEALANT
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 0 9
Adjustable Wrench
Flexible Supply Tube
413mm
(16-1/4)
(29)
355mm
(14)
C/L
C/L OF SEAT POST
HOLES 140mm
(5-1/2) CTR'S.
388mm
473mm
(15-5/16)
(18-1/2)
FINISHED
13mm
FLOOR
(1/2)
305mm
(12)
343mm
C/L OF SUPPLY
(13-1/2)
AS REQUIRED
WAX RING
Sealant
Closet Bolts
3
767mm
(30-1/4)
384mm
(15)
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90 ° , and slide
into place 6" (152 mm) apart and parallel to wall.
5
NUT
WASHER
BOLT
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP" must face up!
Tape Measure
Carpenters Level
CLOSET
FLANGE
A
CLOSET
BOLTS
FLANGE
7 3 0 1 3 8 7 - 1 0 0
Advertisement
Related Manuals for American Standard NEW SAVONA 2097.012
Summary of Contents for American Standard NEW SAVONA 2097.012
-
Page 1: Installation Instructions
Model 2097.012 Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes. - Page 2 INSTALL TOILET Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor. CAUTION: DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED! Install bolt covers: Make sure that the bolt cover area on the toilet is clean and dry (see figure).
-
Page 3: Repair Parts List
Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage. American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine (calcium hypochlorite). -
Page 4: Troubleshooting
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped by American Standard.