Advanced Menu Items - Kenwood TS-990S Instruction Manual

3 MENU

ADVANCED MENU ITEMS

Menu Display
0 Indication Signal Type (Main Band)
1 Indication Signal Type (Sub Band)
2 Output Level (Main Band)
3 Output Level (Sub Band)
4 REF I/O Connector Configuration
5 Reference Oscillator Calibration
6 Bandwidth (Additional Roofing Filter)
7 Attenuation (Additional Roofing Filter)
8 TX Power Down with Transverter Enabled
9 TX Hold After Antenna Tuning
10 Antenna Tuner during RX
11 Linear Amplifier Control (HF Band)
12 Linear Amplifier Control (50 MHz Band)
13 Microphone Gain (FM Mode)
14 PKS Polarity Reverse
15 TX Inhibit While Busy
CTCSS Unmute for Internal Speaker
16
(Main Band)
CTCSS Unmute for Internal Speaker
17
(Sub Band)
18 MSQ Logic State
19 SSQ Logic State
20 MSQ Reverse Condition
21 SSQ Reverse Condition
22 Standby State Low Power Consumption Standby Power Saving
23 Cooling Fan Control after Shutdown
MSQ/ PKS Pin Assignment
24
(COM Connector)
25 External Display
26 Resolution (External Display)
27 Touchscreen Calibration
28 Software License Agreement
Important Notices concerning Free Open
29
Source
About Various Software License
30
Agreements
3-10
Configuration
Output signal type (main band) to an
external meter
Output signal type (sub band) to an
external meter
Output signal level (main band) to an
external meter
Output signal level (sub band) to an
external meter
Configurations for the REF I/O connector Off, Output, Input
Frequency calibration for the reference
oscillator
Passband width of the additional roofing
filter
Attenuation of the additional roofing filter
Transmit power reduction while the
transverter is enabled
Transmit hold time after completing the
antenna tuning
Antenna tuner behavior while receiving
Linear Amplifier Control for use in the HF
band
Linear Amplifier Control for use in the 50
MHz band
Microphone gain in FM mode
Reversion of the PKS polarity
Transmit inhibit while in the busy state
Muting the CTCSS tone (Main band)
Muting the CTCSS tone (Sub band)
Selecting the MSQ Logic
Selecting the SSQ Logic
Reversing conditions of the MSQ logic
state
Reversing conditions of the SSQ logic
state
Cooling fan behavior after shutdown
Pin assignment of MSQ/PKS to the COM
connector
Output to the external display
Video Signal Resolution
Touchscreen calibration
Software License Agreement
Method to obtain the open source
software used in this transceiver
Licensing of the software used in this
transceiver, under the GPL/LGPL
Range
Automatic, TX Power, ALC, Drain
Voltage (Vd), Compression Level
(COMP), Current (Id), SWR
TX Power, ALC, Drain Voltage
(Vd), Compression Level (COMP),
Current (Id), SWR
0 to 100 [%] (in steps of 1)
0 to 100 [%] (in steps of 1)
-255 to +255 (in steps of 1)
Off, 300 to 3500 [Hz] (in steps of
100 [Hz])
-20 to 0 to +20 (in steps of 1)
Off, On
Off, On
Off, On
Off, Active High, Active High +
Relay Control, Active High + Relay
& TX Delay Ctrl, Active Low, Active
Low + TX Delay Control
Off, Active High, Active High +
Relay Control, Active High + Relay
& TX Delay Ctrl, Active Low, Active
Low + TX Delay Control
1 to 100 (in steps of 1)
Off, On
Off, On
Mute, Unmute
Mute, Unmute
Low, Open
Low, Open
Off, Busy, Sql, Send, Busy-Send,
Sql-Send
Off, Busy, Sql, Send, Busy-Send,
Sql-Send
Off, On
Off, On
Off, On
Off, On
800x600, 848x480
-
-
-
-
Index
Reference
Default
Page
Automatic 16-15
ALC 16-16
50 [%] 16-16
50 [%] 16-16
Off 16-22
0 18-1
Off 16-22
0 16-23
On 16-33
Off 4-23
Off 4-22
Off 16-31
Off 16-32
50 5-28
Off 16-29
Off 16-28
Mute 16-23
Mute 16-23
Low 16-24
Low 16-24
Sql 16-24
Sql 16-24
Off
(K-Type)
4-2
On
(E-type)
Off 4-2
Off 16-25
On 16-18
800x600 16-18
- 16-3
- IV
- IV
- IV
Contents