Remington RM1015SPS Operator's Manual page 5

allow the moving chain saw to touch the ground
When cutting through the log maintain control by reducing the cutting pressure as you near the end
of a cut. Do not relax your grip on the chain saw handles. Do not allow the moving chain saw to touch
the ground as this will dull the blade. Cut the log downwards from the top surface (Fig. 12).
After cutting through the log switch off the chain saw by releasing the trigger switch and remove the
chain saw.
How to Buck a Log when it is Supported on One End
WARNING:
If the log is on a slope make sure that it will not roll by securing it. Do this by
driving wooden stakes around the downhill side of the log. When cutting with the chain saw
always stand on the uphill side in case the log rolls during or after cutting.
Never try cutting through two logs at the same time as this could increase the risk of
kickback.
Never hold a log with your hand, leg or foot while cutting the log with the chain saw.
Never allow another person to hold the log while you are cutting it.
Before moving from one work area to another always turn off and unplug the chain saw.
Use the top of the
guide bar to make
the first cut on the
underside of the log
Fig. 13 Bucking a Log when it is Supported on One End
Use the top of the guide bar to make the first cut on the underside of the log (Fig. 13). Make this
cut about 1/3 of the thickness of the log. Doing this will keep this section from splintering when
completely cut.
Make the second cut directly above the first and cut downwards to meet the first cut. Doing this will
keep the log from pinching the guide bar and chain.
How to Buck a Log when it is Supported on Both Ends
Use the bottom of
the guide bar to
make the first cut on
the topside of the log
Fig. 14 Bucking a Log when it is Supported on Both Ends
Use the bottom of the guide bar to make the first cut on the topside of the log (Fig. 14).
Make this cut about 1/3 of the thickness of the log. Doing this will keep this section from splintering
when completely cut.
Make the second cut directly below the first and cut upwards to meet the first cut. Doing this will keep
the log from pinching the guide bar and chain.
CUTTING WITH THE POLE SAW
TRIMMING A TREE - How to safely and efficiently prune the branches of a living tree
WARNING:
Avoid kickback. Kickback can result in severe injury or death. See Kickback
Fig. 1 to avoid risk of kickback.
WARNING:
Do not operate the pole saw if you are in the following situations:
If you are standing or sitting in a tree.
If you are standing on a ladder or on any unstable surface.
If you are in any awkward position whatsoever.
Operating the pole saw in any of these situations may cause you to lose control and result in
severe injury or death.
WARNING:
When using the pole saw do not extend your arms above your shoulders.
CAUTION:
It's advisable for your own safety, to seek professional help if you face pruning
conditions that are beyond your ability.
Fig. 15 Cutting Sequence for Pruning a Tree Limb
Trimming a tree is the process of pruning or removing the overgrown limbs on a living tree. Before you
start cutting with the pole saw, make sure that your footing is firm and stand with your feet apart and
your weight evenly balanced. To safely and efficiently trim a tree limb follow these directions:
1. Use the top of the guide bar to make the first cut on the underside of the limb. This cut should be
about 6" from the tree trunk and about 1/3 of the thickness of the limb (Fig. 15).
2. Move 2" to 4" farther out on the limb and use the bottom of the guide bar to make the second cut
on the topside of the limb. Continue cutting until the limb is completely off the tree (Fig. 15).
3. Use the top of the guide bar to make the third cut on the underside of the limb stump. This should
be made as close as possible to the tree trunk and about 1/3 of the thickness of the limb stump
(Fig. 15).
4. Use the bottom of the guide bar to make the fourth and final cut. Make this cut directly above the
last and downwards through the limb stump (Fig. 15).
POLE SAW INFORMATION - ADJUSTING POLE LENGTH (RM1015SPS)
The Remington RM1015SPS Pole Saw has a telescoping pole assembly that will extend from 57"
(fully retracted) to 96" (fully extended). Two cam levered collets, in their flat position, are used to
clamp and hold the pole securely at any extended length. To do this follow these directions:
Make the second cut
directly above the first
and cut downwards to
meet the first cut
Doing this will keep the log
from pinching the guide bar
and chain
Make the second cut
directly below the first
and cut downwards to
meet the first cut
Doing this will keep the log
from pinching the guide bar
and chain
4th Cut - 2nd Cut -
Final Stub Pruning Cut
Cut (to avoid pinching)
6"
2" to 4"
1st Cut -
Pruning Undercut
(to avoid splintering)
3rd Cut -
Stub Undercut
(to avoid splintering)
OPERATING INSTRUCTIONS
1. To extend the pole, loosen and turn the cam levered collet to its upright position (Fig. 16).
2. Slide the pole to the desired length.
3. To lock and secure the pole in place, return the cam levered collet to its flat position.
NOTE: For your own safety, it's best to extend the pole to the minimum length required to reach the
limb that is being cut. Otherwise you may lose your balance and the pole saw may fall.
To extend the pole,
loosen and turn the
cam levered collet
to its upright position
CUTTING WITH THE POLE SAW
Never stand directly under the limb
you are trimming. Always position
yourself out of the path of falling debris.
Do not use the pole saw to cut limbs
that are larger in diameter than the
length of the guide bar.
Position yourself near the tree limb that you wish to cut.
1. Connect the pole saw power plug to the power extension cord. Insert the power extension cord
Make sure that your footing is firm and stand with your
plug into the main power outlet.
feet apart and your weight evenly balanced.
2. Firmly grip the pole saw with both hands in the designated areas shown in Fig. 17. Use a firm grip
and wrap your thumbs and fingers around the pole saw handle and the pole.
3. Position yourself near the tree limb that you wish to cut. Make sure that your footing is firm and
stand with your feet apart and your weight evenly balanced.
4. When you are ready to make a cut, press the trigger lockout switch in with your right thumb while
also squeezing the trigger with your right hand fingers (Fig. 17). This will immediately switch the
power of the pole saw on. Releasing the trigger switches it off.
5. Make sure the pole saw is running at full speed before starting a cut.
6. When starting a cut, place the moving pole saw against the tree limb (Fig. 17). Hold the pole saw
firmly in place while cutting through the limb. This will help to prevent a possible bouncing or
skating, sideways movement of the log.
7. Guide the pole saw by applying light pressure as you cut. Do not force the pole saw as the motor
may overload and burn out. It will do the job better and safer at the rate for which it was intended.
8. Remove the pole saw from the cut while it is still running at full speed. Stop the pole saw by
releasing the trigger. Make sure that the chain has completely stopped before setting it down.
Slide the pole to
the desired length
Fig. 16 How to Adjust the Length of the Pole Saw
Never stand on a ladder or
other type of unstable support.
Always use both hands
to operate the pole saw.
Firmly grip the pole saw with
both hands in the designated
areas shown here.
Use a firm grip and wrap your
thumbs and fingers around the
pole saw handle and the pole.
Fig. 17 How to Use the Pole Saw to Safely Prune a Tree Limb
To lock and secure the pole in
place, return the cam levered
collet to its flat position
When you are ready to make a
cut, press the trigger lockout
switch in with your right thumb
while also squeezing the trigger
with your right hand fingers.
This will immediately switch the
power of the pole saw on.
Releasing the trigger switches
it off.
Make sure the pole saw is
running at full speed before
starting a cut.
Always keep other persons away
from cutting end of the pole saw
and at a safe distance from
the work area.
Do not use the pole saw near cable,
electric power or telephone lines.
Always maintain a minimum
clearance of 50 feet from all power
and utility lines.
5