Table of Contents
Advertisement
Insignia 32" LED TV
10 If the channel list has been deleted and the TV
Setup wizard opens, go through the TV SETUP
wizard. For more information, see "Turn on your
TV for the first time" on page 36.
Note
• If you see a message that says the
firmware file is incorrect, make sure
that you have downloaded the correct
file for your model.
• If you see a message that says the
update failed or the TV screen is blank
and the power LED is blinking red
then blue, turn off your TV, turn it back
on, then run the upgrade again.
Video and audio
Problem
Solution
Picture does not
• Change the aspect ratio. An
fill the screen.
There are black
bars around the
picture.
No picture (screen
• Press
is not lit) and no
sound.
• Make sure that the Audio Only
• Make sure that the video cables
• Adjust the contrast and
• Make sure that the AC power
• Make sure that the correct video
• Try another channel. The station
• Make sure that the incoming
• Make sure that the antenna or
• Check the closed caption
increasing amount of digital TV
and movies are presented in
wide screen (16:9). See the
"Aspect Ratio" option in "Adjust
the TV picture" on page 47.
on the TV or the
remote control.
option is set to Off. See "Play TV
audio only" on page 51.
are connected securely to your
TV.
brightness. See "Adjust the TV
picture" on page 47.
adapter is plugged in.
input source is selected. See
"Select the video input source"
on page 38.
may be experiencing problems.
signal is compatible.
cable TV is connected correctly
and securely. See "Connect a
cable or satellite box" on
page 13 or "Connect an
antenna or cable TV (no box)"
on page 18.
settings. Some TEXT modes can
block the screen. See "Select the
analog closed captioning
mode" on page 59 or "Select
the digital closed captioning
mode" on page 60.
www.insigniaproducts.com
Problem
Solution
Dark, poor, or no
• Try another channel. The station
picture (screen is
lit), but sound is
• Make sure that the antenna or
good.
• Adjust the brightness. See
• Change to a different picture
• If you are using an antenna, the
• If you are using an antenna and
• Make sure that the video cables
• The video cable(s) you are using
• Try another channel. The station
No color, dark
• Try another channel. The station
picture, or color is
not correct.
• Adjust the color settings. See
• Make sure that the video cables
• Make sure that the antenna or
• If you are using an antenna, the
• If you are using an antenna and
may be experiencing problems.
cable TV is connected correctly
and securely. See "Connect a
cable or satellite box" on
page 13 or "Connect an
antenna or cable TV (no box)"
on page 18.
"Adjust the TV picture" on
page 47.
mode. See "Adjust the TV
picture" on page 47.
digital channel signal may be
low. To check the digital
channel signal strength, see
"Check the digital signal
strength" on page 54.
the signal strength is low, adjust
the antenna or use a highly
directional outdoor antenna or
set-top antenna with a built-in
amplifier.
are connected securely to your
TV.
may be bad. Try a new set.
may be experiencing problems.
may be experiencing problems.
"Adjust the TV picture" on
page 47.
are connected correctly and
securely to your TV.
cable TV is connected correctly
and securely. See "Connect a
cable or satellite box" on
page 13 or "Connect an
antenna or cable TV (no box)"
on page 18.
digital channel signal may be
low. To check the digital
channel signal strength, see
"Check the digital signal
strength" on page 54.
the signal strength is low, adjust
the antenna or use a highly
directional outdoor antenna or
set-top antenna with a built-in
amplifier.
65
Advertisement
Table of Contents
