Setting Current Day And Time; Installer System Test - Honeywell TRADELINE T7200D Installation Instructions Manual

T7200D,E SERIES 2000 COMMERCIAL MICROELECTRONIC THERMOSTATS
Installer Setup
Number
(Press
Unoccupied
Temp key
to change)
Select
Minimum off- 38
times in heating.
Installer Setup 40
lockout (keypad
lockout is
enabled and
disabled by dip
switch 1 on back
of thermostat).
IMPORTANT
Review the settings to confirm that they match
the system. Press Run Program to exit the
Installer Setup. Set the current day and time
immediately.

Setting Current Day and Time

1. Press Set Current Day/Time.
NOTE: On initial power up or after an extended
power loss, 1:00 pm flashes on the LCD
until a key is pressed.
Set Current
Day/Time Set Program
Run Occupied Unoccupied
Program Start Time Start Time
Temporary Set Current Clear
Occupied Day/Time Start Time
Continous
Unoccupied
2. Press Day until the current day is displayed.
NOTE: Sun=Sunday, Mon=Monday,
Tue=Tuesday, Wed=Wednesday,
Thu=Thursday, Fri=Friday, Sat=Saturday.
Day
Set Program
Run Occupied Unoccupied
Program Start Time Start Time
Temporary Set Current Clear
Occupied Day/Time Start Time
Continous
Unoccupied
3. Press increase
time is displayed.
NOTE: Tapping the Set Current Day/Time changes
the time in one hour increments.
Set Program
Run Occupied Unoccupied
Program Start Time Start Time
Temporary Set Current Clear
Occupied Day/Time Start Time
Continous
Unoccupied
62-0128—2
Table 2. Thermostat Installer Setup Options (Continued).
Factory Setting
Display
4 4—4-minute
0 0—No Installer Setup
Set Day/Time
PM
Set Temperature Change
Time/Temp
Occupied Unoccupied
Day Temp Temp Mon
Heat/Cool
Copy Settings
System Fan
Set Day/Time
PM
Set Temperature Change
Time/Temp
Occupied Unoccupied
Day Temp Temp Tue
Heat/Cool
Copy Settings
System Fan
or decrease until the current
Set Day/Time
PM
Set Temperature Change
Time/Temp
Occupied Unoccupied
Day Temp Temp
Tue
Heat/Cool
Copy Settings
System Fan
Description Display
0, 1, 2, 3,
minimum off-time. or 5
1
lockout.
4. Press Run Program.
Program

INSTALLER SYSTEM TEST

Use the Installer System Test to check the thermostat
configurations and operation. Refer to Table 3 for a list of
the available system tests.
Table 3. Tests Available in Installer System Test.
Test
Number
M4951B
10 to 19
30 to 39
40 to 49
60 0 to
60 19
70 to 79
M4952B
To start the system test:
CAUTION
Possible Equipment Damage.
Equipment damage can result if compressor is
cycled too quickly.
The minimum off-time for compressors is bypassed
during the Installer System Test.
Press and hold the increase
M4953B
the same time, until 10 appears. All segments of the LCD
are displayed for three seconds before 10 appears. See
Fig. 10 and 11.
6
Other Choices
(Press or key to change)
Description
Minimum number of minutes
(0 thru 5) the heating
equipment will be off
between calls for heat.
1—Installer Setup lockout
activated.
Run
Set Program Set Temperature Change
Time/Temp
Run Occupied Unoccupied Occupied Unoccupied
Program Start Time Start Time Day Temp Temp
Temporary Set Current Clear Heat/Cool
Occupied Day/Time Start Time Copy Settings
Continous
Unoccupied System Fan
System Test Description
Heating equipment can be turned on and
off
Cooling equipment can be turned on and
off
Fan equipment can be turned on and off
Keyboard keys test
Thermostat information including date
code, software versions and subbase
identification are displayed
and decrease
Actual
Setting
AM
Room
Mon
Occupied 1
System Fan
Auto
Heat
M4954A
keys, at