Table of Contents
Advertisement
T8611G CHRONOTHERM
IMPORTANT
Review the settings to confirm that they match
the system. Press Run Program to exit the
Installer Setup. The thermostat has saved the
Installer Setup changes and initiated a reset in
order to operate using the new settings. Be sure
to set the current day and time immediately.
Setting Current Day and Time
1. Press Set Current Day/Time.
NOTE: On initial power up or after an extended
power loss, 1:00 pm flashes on the
display until a key is pressed.
Set Current
Time
Set Program
Run
Set Current
Wake
Leave
Program
Day/Time
Day/Time
Heat/Cool
Hold Temp
Day
Settings
Daylight
Copy
Time
2. Press Day until the current day is displayed.
NOTE: Sun=Sunday, Mon=Monday,
Tue=Tuesday, Wed=Wednesday,
Thu=Thursday, Fri=Friday, Sat=Saturday.
Time
Set Program
Run
Set Current
Wake
Leave
Program
Day/Time
Day
Heat/Cool
Hold Temp
Day
Settings
Daylight
Copy
Time
3. Press Time
or Time
displayed.
NOTE: Tapping the Set Current Day/Time will
change the time in one hour increments.
Time
Time
Set Program
Run
Set Current
Leave
Wake
Program
Day/Time
Heat/Cool
Hold Temp
Day
Settings
Daylight
Copy
Time
NOTE: If the current time is Daylight Savings
Time, press Daylight Time until DST is
displayed.
Time
Set Program
Daylight
Set Current
Run
Wake
Leave
Program
Day/Time
Time
Heat/Cool
Hold Temp
Day
Settings
Daylight
Copy
Time
4. Press Run Program.
Time
Set Program
Run
Run
Set Current
Wake
Leave
Program
Day/Time
Program
Heat/Cool
Hold Temp
Day
Settings
Daylight
Copy
Time
Set Day/Time
PM
Mon
Return
Sleep
System
Fan
Set Day/Time
PM
Tue
Return
Sleep
System
Fan
until the current time is
Set Day/Time
AM
Tue
Return
Sleep
System
Fan
Set Day/Time
AM
Tue
Return
Sleep
DST
System
Fan
AM
Tue
Return
Sleep
Wake
System
DST
System
Fan
Heat
®
IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATS
INSTALLER SYSTEM-TEST
Use the Installer System-Test to check the thermostat
operation. Refer to Table 4 for a list of the available
system-tests.
To start the system-test:
CAUTION
The minimum off time for compressors is
bypassed during the Installer System-Test.
Equipment damage can occur if the compressor
is cycled too quickly.
Press and hold the increase
the same time until 10 appears. All segments of the
display will be displayed before the 10 appears. See
Fig. 11 and 12.
Table 4. Tests Available In The Installer System-Test.
M10312
Test
Number
10-19
20-29
30-39
40-49
M10313
60 0 to
60 19
70-79
Set Program
Hold for
Em Ht
Aux Ht
M10314
Mon
TueWedThuFriSatSun
Wake
LeaveReturnSleep
System
Em Heat
Fig. 11. Display of all the segments of the LCD.
M10315
Room
Fan
Auto
M10316
7
and decrease
System-Test Description
Heating equipment can be turned on
and off
Emergency heat equipment can be turned
on and off
Cooling equipment can be turned on
and off
Fan equipment can be turned on and off.
Keyboard keys test
Thermostat information including date
code and software versions are displayed
Temporary Setting Enrg
Start Time
Set Day/Time
AM
PM
Heat
In
Recovery
DST
Off
Cool
Auto
Wait
TEST NUMBER
Fig. 12. Display of test number.
keys at
Sav
Room
%Humid
Cool
Outdoor
Auto
Repl Batt
Fan
On
Auto
M10345
M10257A
69-0936—1
Hide quick links:
Advertisement
Table of Contents
