Installer Setup - Honeywell CHRONOTHERM T8600D Product Data

T8600D, T8601D AND T8602D CHRONOTHERM
System settings control the thermostat operation as follows:
Heat: The thermostat controls the heating.
Off: Both the heating and cooling are off.
Cool: The thermostat controls the cooling.
Auto: The thermostat automatically changes between
heating and cooling operation, depending on the indoor
temperature.
Fan settings control the system fan as follows:
On: Fan operates continuously.
Auto: Fan operates with equipment.
Time
Run Set Current
Wake Leave
Program Day/Time
Heat/Cool
Hold Temp Day
Settings
Daylight
Copy
Time
Fig. 7. Thermostat System and Fan key locations.
NOTE: Always press the keys with your fingertip or similar
blunt tool. Sharp instruments like a pen or pencil
point can damage the keyboard.
Temperature Settings
Refer to Table 5 for the default program. If the daytime energy
savings period is not used, press the period key (Leave or
Return) until the time is blank. The fan setting feature is
available on select thermostat models. See Programming
Section for complete instructions on changing the program.
Table 5. Default Program Settings.
Heat
Period Time Setpoint
Wake 6:00 AM 70°F
(21°C)
Leave 8:00 AM 62°F
(16.5°C)
Return 6:00 PM 70°F
(21°C)
Sleep 10:00 PM 62°F
(16.5°C)

INSTALLER SETUP

NOTE: For most applications, the thermostat factory-
settings will not need to be changed. Review the
factory settings in Table 6 and if no changes are
necessary, go to the Installer System Test section.
®
Set Program
Return Sleep
System
System Fan
Fan
M15042
Cool Fan
Setpoint Setting
78°F Auto
(25.5°C)
85°F Auto
(29.5°C)
78°F Auto
(25.5°C)
82°F Auto
(28°C)
IV DELUXE PROGRAMMABLE THERMOSTATS
The Installer Setup is used to customize the thermostat to
specific systems. Some of the options include temperature
display, changeover and outdoor temperature display. Installer
Setup numbers are listed in Table 6. The table includes all the
configuration options and the factory-settings for the
thermostat.
A combination of key presses are required to use the Installer
Setup feature.
— To enter the Installer Setup, press and hold the
Information i key with the increase
keys until the first number is displayed. All display
segments appear for approximately three seconds before
the number is displayed. See Fig. 8 and 9.
— To advance to the next Installer Setup, press the Time
key.
— To change a setting, use the increase
key.
— To scroll the Installer Setup numbers backwards, press
the Time key.
— To exit the Installer Setup, press Run Program.
Set Program Start Time
Hold for
Em Ht
Aux Ht
Mon TueWedThuFriSatSun
Wake LeaveReturnSleep
System
Em Heat Off Cool
Fig. 8. Display of all the segments of the LCD.
INSTALLER SETUP
NUMBER DISPLAY
(COLUMN 2
OF TABLE 6)
Fig. 9. Display of Installer Setup number and setting.
CAUTION
Heat pump and electric heat systems must be
configured to 1 in Installer Setup number 2 to prevent
equipment damage caused by the system running
without the fan.
IMPORTANT
Only configurable numbers are shown on the device.
Example: If thermostat does not have a system key,
Installer Setup Number 12 will not be displayed.
Review Table 6 factory-settings and mark any
desired changes in the Actual Settings column.
When Installer Setup is complete, review the settings
to confirm that they match the system.
7
and decrease
or decrease
Temporary Setting Enrg
Set Day/Time
AM
Room
PM
%Humid
Heat Cool Outdoor
In Recovery Auto Repl Batt
DST Fan
Auto Wait On
FACTORY SETTING
OR OTHER CHOICE
DISPLAY (COLUMN 3
OR 5 OF TABLE 6)
Sav
Auto
M10345
M10404
68-0164—1