Honeywell FUSION User Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. DVR
  5. FUSION
  6. User manual
Honeywell FUSION User Manual

Honeywell FUSION User Manual

Digital recording and transmission system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
FUSION DVR
Digital Recording and Transmission System

User Manual

DRMU000834–Rev. J – March 2005

Advertisement

Table of Contents
loading

Related Manuals for Honeywell FUSION

Summary of Contents for Honeywell FUSION

  • Page 1: User Manual

    FUSION DVR Digital Recording and Transmission System User Manual DRMU000834–Rev. J – March 2005...
  • Page 2 Revised PTZ information. Updated format and content (PCN 1718). Updated format and content. Updated content, clarified ambiguous feature descriptions, and updated DVR chassis images. Updated content for v.2.3.2 software release. Updated G2 images and UL power safety requirements. Updated format and content.

  • Page 3: Fcc Compliance Statement

    USERS OF THE PRODUCT ARE RESPONSIBLE FOR CHECKING AND COMPLYING WITH ALL FEDERAL, STATE, AND LOCAL LAWS AND STATUTES CONCERNING THE MONITORING AND RECORDING OF VIDEO AND AUDIO SIGNALS. HONEYWELL VIDEO SYSTEMS SHALL NOT BE HELD RESPONSIBLE FOR THE USE OF THIS PRODUCT IN VIOLATION OF CURRENT LAWS AND STATUTES.
  • Page 4 NATIONAL POWER DEVIATION STANDARDS AUSTRALIA / NEW ZEALAND COMPONENTS COMPLY WITH THE RELEVANT PORTIONS OF IEC 60950 OR THE APPLICABLE COMPONENT STANDARD OR THE RELEVANT AUSTRALIAN / NEW ZEALAND STANDARD. AC POWER DISTRIBUTION SYSTEMS CLASSIFIED AS TT OR IT ARE NOT ALLOWED INTENDED FOR USE ON A TN SYSTEM.
  • Page 5 EQUIPMENT HAVING A RATED CURRENT EXCEEDING 13 A IS PROVIDED WITH A SUPPLY CORD WITH A PLUG, THIS PLUG SHALL BE IN ACCORDANCE WITH THE HEAVY CURRENT. GERMANY (GESETZ UBER TECHNISCHE ARBEITSMITTEL (GARATESICHERHEITSGESETZ) [LAW OF TECHNICAL LABOUR EQUIPMENT {EQUIPMENT SAFETY LAW}], OF 23RD OCTOBER 1992, ARTICLE 3, 3RD PARAGRAPH, 2ND SENTENCE, TOGETHER WITH THE "ALLGEMEINE VERWALTUNGSVORSCHRIFT ZUR URCHFUHRUNG DES ZWEITEN ABSCHRITTS DES GERATESICHERHEITSGESETZES"...

  • Page 6: Rack Mount Instructions

    RACK MOUNT INSTRUCTIONS A) Elevated Operating Ambient – If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
  • Page 7 EN 50130-4:1996 Notice 1. Uninterrupted Power supply (UPS) 2. Maximum lengths of wiring connected to the sensor inputs and control outputs are 30 meters. EN 55022 CLASS A Notice WARNING This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
  • Page 8 OPTICAL AND ACOUSTICAL STATEMENTS VISIBLE LED STATEMENT The LEDs on this DVR unit are classified as “Class 1 LED Product” in accordance with EN 60825-1. LASER SAFETY STATEMENT FOR A CLASS 1 LASER PRODUCT This CD-ROM Storage device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

  • Page 9: Important Safeguards

    Object and Liquid Entry Points – Never insert foreign objects into the DVR unit, other than the media types approved by Honeywell, as they may touch dangerous voltage points or short-out parts that could result in a fire or electrical shock. Never spill liquid of any kind on the product.

  • Page 10: Notes On Handling

    This is not a malfunction. NOTES ON LOCATING • Place the DVR unit on a level surface. Do not use it on a shaky or unstable surface such as a wobbling table or inclined stand. • When you place this DVR unit next to a TV, radio, or VCR, the playback picture may become poor and the sound may be distorted.

  • Page 11: Notes On Maintenance

    If you use the DVR unit in such a situation, it may damage discs and internal parts. Remove any CD discs, connect the power cord of the DVR unit to the wall outlet, turn on the DVR unit, and leave it for two to three hours.

  • Page 12: Explanation Of Graphical Symbols

    WARNING TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, NO USER-SERVICEABLE PARTS INSIDE.

  • Page 15: Table Of Contents

    LOOPING OUTPUTS... 3–6 LOOPING OUTPUT TERMINATION ... 3–7 CONNECTING SENSORS TO THE DVR ... 3–7 3.10 CONNECTING CONTROL OUTPUTS TO THE DVR ... 3–8 3.11 ADDITIONAL OUTPUTS AND CONNECTORS... 3–9 3.12 OPTIONAL COMPONENTS ... 3–10 SECTION 4 DVR BASICS ... 4–1 TURNING ON THE DVR...
  • Page 16 5.14.3 SELECT SITE ... 5–37 5.14.4 SETTING UP THE CENTRAL MANAGEMENT USER SERVER ... 5–37 5.14.5 ENABLING A DVR TO USE CENTRAL USER MANAGEMENT ... 5–38 5.15 TV OUTPUT CONTROL SETUP (OPTIONAL) ... 5–38 5.15.1 CUSTOMIZING THE TV OUTPUTS... 5–40 SECTION 6 SEARCH OPTIONS ...
  • Page 17 DAYLIGHT SAVINGS TIME ... 6–7 TIME SYNC... 6–7 6.10 PRINTING AN IMAGE ... 6–8 6.11 ‘SAVE TO’ FUNCTION ... 6–8 6.12 INDEX SEARCH ... 6–10 6.12.1 PERFORMING AN INDEX SEARCH... 6–10 6.13 PREVIEW SEARCH... 6–12 6.13.1 PERFORMING A PREVIEW SEARCH... 6–13 6.14 OBJECT SEARCH ...
  • Page 18 13.2 SETTING UP THE SERVER TO ACCEPT INCOMING CONNECTIONS ... 13–3 13.2.1 CONFIGURING THE DVR SERVER TO ACCEPT REMOTE CONNECTIONS... 13–3 13.3 SETTING UP THE FUSION REMOTE SOFTWARE... 13–4 13.3.1 INSTALLING THE FUSION REMOTE SOFTWARE ... 13–4 13.3.2 CREATING A NEW REMOTE CONNECTION... 13–4...
  • Page 19 14.1.1 CONFIGURING THE DVR SERVER TO ACCEPT REMOTE CONNECTIONS... 14–2 14.1.2 CONNECTING TO A DVR WITH THE WEB VIEWER... 14–2 14.1.3 CLOSING THE WEB VIEWER ... 14–3 SECTION 15 TECHNICAL SPECIFICATIONS ... 15–1 15.1 HFDVR FUSION 8-CHANNEL... 15–1 15.2 HFDVR FUSION 16-CHANNEL... 15–2 15.3 HFDVR FUSION 32-CHANNEL... 15–3...
  • Page 20 NOTES:...

  • Page 21: Section 1 Introduction

    PRODUCT DESCRIPTION The Honeywell Fusion DVR is simply a server that performs as a High Definition Digital Recorder. By utilizing the many features of a computer, including processing power, storage capacity, graphics compression, and security features, the DVR unit is more powerful than the analog recorders of the past.
  • Page 22 FUSION DVR Digital Recording and Transmission System FEATURES, CONTINUED • Up to 32 Looping Outputs • Optional POS and ATM Support • 1 Composite Output • S Video Output • Up to 32 Camera Inputs • High Performance, Durable, Rack mount Case •...

  • Page 23: Section 2 Controls And Connections

    BASIC FEATURES Honeywell’s state-of-the-art High Definition Digital Recorders are housed in a high performance and versatile 4U Aluminum Rack-Mount case allowing easy storage of multiple DVRs for enterprise applications. Every Fusion DVR Unit comes equipped with the latest technology •...

  • Page 24: Front Panel Controls And Leds

    FRONT PANEL CONTROLS AND LEDS The front panel of the DVR unit contains the devices that will be commonly used for data removal, retrieval, and backup replacement. The most common components and buttons are shown below. REAR PANEL CONNECTORS 2–2...
  • Page 25 The rear panel of the DVR unit contains virtually all of the connectors you will be using. Below is a diagram that outlines the location and description of each connector: 32 Channel CONTROL SENSOR Description BNC Connectors for Video Input and...
  • Page 26 CONTROL SENSOR Description BNC Connectors for Video Input and Looping Outputs Control Alarm Outputs / Sensor Inputs Termination Switches Audio Inputs RS-422 Interface RCA Video OUT Exhaust Fan S-Video Output DB-15 SVGA Monitor Output Audio Microphone In Audio Speaker Out 2–4 CH 1 in CH 2 in...

  • Page 27: Section 3 Getting Started

    IDENTIFYING INCLUDED COMPONENTS Honeywell’s Fusion DVRs come with a mouse, keyboard and selected software and cables. Identify the following components to make sure everything has been properly included with your new DVR unit. If any of the following items are missing, contact your dealer to arrange a replacement.

  • Page 28: Keyboard Setup

    Connectors for more information. MOUSE SETUP To attach the mouse to the DVR unit, plug the end of the mouse cable into the mouse PS/2 Port located on the back of the machine. The mouse PS/2 Port can be identified by the green color.

  • Page 29: Monitor Setup

    MONITOR SETUP Attach the Monitor to the Rear of the DVR unit using the VGA cable supplied by the Monitor Manufacturer. Refer to the monitor manual for detailed information on how to setup and use it. NOTE: The monitor you use must be capable of having a screen resolution of 1024 x 768 and display colors of at least 32 Bit.

  • Page 30: Connecting A Video Source To The Dvr

    8-Channel DVR Inputs # 1-8 The Video inputs are BNC connectors. Simply plug one end of the BNC-BNC cable into your video source (DVD, Camera, etc.) and plug the other end into the desired BNC input on the DVR unit. 3–4...
  • Page 31 CONNECTING A VIDEO SOURCE TO THE DVR, CONTINUED 16 Channel DVR Inputs # 1-16 32 Channel DVR Inputs # 1-32 3–5...

  • Page 32: Looping Outputs

    LOOPING OUTPUTS The 8 and 16 Channel DVR units may have up to 16 Looping outputs. Depending on the destination of the outputs, each output may have to be terminated. 8 Channel DVR Outputs # 1-8 16 Channel DVR Outputs # 1-16 The Video inputs are BNC connectors.

  • Page 33: Looping Output Termination

    Always leave the dipswitch set to the ON position when the Looping Outputs are not used. CONNECTING SENSORS TO THE DVR Each DVR unit may have up to 16 Sensor inputs. These inputs can be used with devices such as Infrared sensors, motion devices, glass break alarms, door and window trips, and many more.

  • Page 34: Connecting Control Outputs To The Dvr

    3.10 CONNECTING CONTROL OUTPUTS TO THE DVR Each DVR unit may have up to 16 Control Outputs. These outputs can be used to trigger devices such as Sirens, Phone Dialers, Lights, and any other relay activated device. Control Output •...

  • Page 35: Additional Outputs And Connectors

    3.11 ADDITIONAL OUTPUTS AND CONNECTORS 240/480 FPS 120 FPS Signal Line (+) Ground Signal Line ( -) RX LED TX LED Operation Signal Line (+) Signal Line ( PTZ to RS 232 converter 3–9...

  • Page 36: Optional Components

    3.12 OPTIONAL COMPONENTS To fully utilize your DVR unit’s potential, several optional Fusion components are listed below. Contact your dealer for more information. DVD ROM Recordable Drive USB External Hard Drive Fiber Network Interface Adapter Gigabit 10/100/1000 NIC Adapter Fusion Remote Video Software...

  • Page 37: Section 4 Dvr Basics

    1. Turn on the monitor and any external peripherals (ex. Printers, External Storage Devices, etc.) connected to the DVR unit. 2. Turn on the main power switch located on the front of the DVR unit as shown below. (See Section 2.2 – Front Panel Controls for location of the main power switch.)

  • Page 38: Display Screen

    DISPLAY SCREEN Each time the DVR is restarted, the program defaults to the Display screen. The following diagram outlines the buttons and features used on the Display screen. Become familiar with these options as this is the screen that will be displayed the majority of the time.
  • Page 39 Restart in Windows Mode. Displays the name of the user currently logged onto the DVR. Displays users connected remotely to the DVR unit. Displays Alarm Status for each Sensor Input. The Digital Output Relay button fires the Output Relay.

  • Page 40: Camera View

    A red light is displayed when the camera is currently being recorded to the DVR unit. A green light is displayed when a camera (set up for motion detection) detects motion A square is displayed when the camera is currently not being recorded to the DVR unit.

  • Page 41: Screen Division Menu

    Special There are several different types of DVR “Special Recording” situations. Recording When this happens, text is displayed on the camera indicating what kind it is. Sensor Displays when a sensor, associated with a given camera, is activated. Instant Instant Recording is a manual activation of the recording for the selected camera.
  • Page 42 SCREEN DIVISION MENU, CONTINUED Four Cameras Eight Cameras Eight Cameras Multi-Camera View All Camera View Multi-Camera View Multi-Camera View Full Screen AUTO-SEQUENCE 4–6 Displays cameras 13-16 in the Video Display Area. To return to a different Multi-Camera View, select a different Screen Division option from the Screen Division menu.

  • Page 43: Tv Output Controls (Optional)

    The TV OUT options allows manual control the 4 analog outputs on the back of the DVR. Within setup the outputs can be programmed to sequence through any number of cameras, however, by using the TV OUT options that defined sequence can be temporarily stopped and a camera can be manually selected to output.
  • Page 44 FUSION DVR Digital Recording and Transmission System NOTES: 4–8...

  • Page 45: Section 5 Setup Options

    • DVR Access – By setting up the access passwords better control of the types of access any individual may have. This ensures the security and integrity of the DVR.

  • Page 46: Camera Setup

    CAMERA SETUP Select Camera Video Display Camera Name Adjust Default Adjust All Default Bright Contrast 5–2 Selects the current camera to be edited. Displays the live video of the current camera selected. Ability to specify a name for each camera. (up to 14 characters for every camera) Adjusts the color settings for the selected camera back to the system default.

  • Page 47: Motion

    MOTION Select Camera Pre-Alarm Motion Region Setup Full Screen Pop-Up on Sensor Sensitivity Selects the current camera to be edited. Allows record of a section of video just prior to motion or sensor activation. The box displays the video for the selected cameras and allows you to create up to 5 motion regions.

  • Page 48: Creating A Motion Area

    This option allows you to record a single frame every few minutes or every few hours to show that the DVR is still functioning even when motion is not taking place. This option only works when Motion recording...

  • Page 49: Regular Interval Recording

    MOTION, CONTINUED 5.3.3 REGULAR INTERVAL RECORDING Motion To enable regular Interval Recording on Motion follow these steps: 1. Setup a camera to record on motion. 2. Place a check in the Regular Interval Recording box. 3. Specify how often to take an image when no motion is occurring. You can go as little as 1 image per second.

  • Page 50: General Setup

    GENERAL SETUP Voice Warning Hide Network Connectivity Display Relay Output Status Bar Display Sensor Status Bar Display Motion Detection Area Box OSD Font Size OSD Bold 5–6 Provides an audible warning (.wav sound clip) when motion or sensors are activated. Enables/Disables display of the Network Connectivity on the Main Display Screen.

  • Page 51: Voice Warning

    5.4.1 VOICE WARNING The DVR unit can be set to play a sound file when either a Motion or Sensor event occurs. This file can be a custom created sound file that is unique to your application. The selected WAV file is played through speakers attached to the DVR unit.

  • Page 52: Intensive Recording Overview

    Adjusts the frame rate for the intensive channel. Adjusts the resolution for the intensive channel. The DVR automatically adjusts the non-intensive channels down to the system default. This setting cannot be changed. Adjusts the amount of time to hold the intensive...

  • Page 53: How To Use Intensive Recording

    5.4.4 VIDEO LOSS ALARM The DVR supports a Video Loss Alarm function which allows an Alarm Event to occur when a camera loses its signal. The lost signal can be due to Power failure to the camera, the camera cable being cut or unplugged, or the camera being damaged in some way.

  • Page 54: Audio Recording

    GENERAL SETUP, CONTINUED 5.4.5 AUDIO RECORDING The Fusion DVR is capable of recording up to 4 channels of audio. Audio Features: • 8000Hz playback in Live Mode • Audio input level should be 1Vp-p • Up to 48000Hz playback in search mode •...

  • Page 55: Frame Setup

    SETUP OPTIONS FRAME SETUP The Frame Setup menu gives the user the option to adjust both the resolution and the number of images per second each camera will record. NOTE: The Software will not allow the maximum available Frames to be exceeded. 5–11...
  • Page 56 Quality Sensitivity Resolution affects the total number of frames per second that are available. The table below breaks down the number of frames available on a 240IPS DVR. 5–12 Selecting this option resets all camera frames and resolutions to the default settings.

  • Page 57: Recording Schedule

    SETUP OPTIONS RECORDING SCHEDULE Creating a customized Schedule is important to maximize the efficiency of the DVR. This DVR offers numerous options to allow for a wide variety of different needs and requirements. 5–13...
  • Page 58 RECORDING SCHEDULE, CONTINUED Pre-Defined Schedules Day of Week Schedule Time Chart Schedule Number Special Day Recording Schedule Camera, Sensor, Relay Alarm Options 5–14 These schedules are created for the general installation and have been predefined with basic configurations All set to Motion – All cameras are set to motion recording (24 hours/day, 7 days/week) All set to Continuous –...

  • Page 59: Day Of The Week

    RECORDING SCHEDULE, CONTINUED 5.6.1 DAY OF THE WEEK The Day of Week is simply the day of the week for which the schedule is being edited. If WED is checked, Wednesday’s schedule is being edited. The Single Day Selection button allows selection of multiple days at once. By selecting the Single Day Selection button placing multiple checks in the boxes is allowed, thereby selecting multiple days simultaneously.
  • Page 60 RECORDING SCHEDULE, CONTINUED Steps 1-6: Schedule cameras 1-4 to record on MOTION from 9:00am-5:59pm Monday through Friday. 1. Select Sch01 from the Schedule Number drop down list. (This should already be selected by default) 2. Select the Single Day Selection button, then select Yes. 3.
  • Page 61 RECORDING SCHEDULE, CONTINUED Steps 7-11: Schedule cameras 1-4 to record on CONTINUOUS from 6:00pm-8:59am Monday through Friday. 7. Select Sch02 from the Schedule Number drop down list. 8. On the Sch02 line again, highlight the hours 18-23 (for 6:00pm-midnight) and press Set.
  • Page 62 RECORDING SCHEDULE, CONTINUED Steps 12-19: Schedule cameras 1-4 to record on MOTION from 12:00am-11:59pm Monday through Friday 12. Select the Multi-Day Selection button. 13. Place a check in the SAT days of the week box. 14. Select Sch03 from the Schedule Number drop down list. 15.

  • Page 63: Scheduling Sensors And Relays (By Example)

    RECORDING SCHEDULE, CONTINUED 5.6.3 SCHEDULING SENSORS AND RELAYS (BY EXAMPLE) It is easy to add advanced recording functionality using Sensor Inputs and Relay Outputs. SENSOR - Sensor Inputs can be programmed to instantly start one or more cameras recording when an alarm occurs. These alarm events can also activate Relay Outputs as desired.
  • Page 64 RECORDING SCHEDULE, CONTINUED Steps 1-8: Schedule cameras 1 and 2 to be activated on Sensor # 3 and/or Sensor #5 which will then activate Relay Output #7 and #13. 1. Select Sch01 from the Schedule Number drop down list. (This should already be selected by default.) 2.
  • Page 65 SETUP OPTIONS RECORDING SCHEDULE, CONTINUED Steps 9-15: Schedule camera 3 to record using MOTION. When Motion occurs it will activate Relay Output #7 and #10. 9. Select Sch02 from the Schedule Number drop down list. 10. Select the Single Day Selection button, then select Yes. 11.
  • Page 66 FUSION DVR Digital Recording and Transmission System RECORDING SCHEDULE, CONTINUED Steps 16-22: Schedule Sensor #6 to activate Relay #8 when an Alarm occurs. NOTE - This will not cause any cameras to record. 16. Select Sch03 from the Schedule Number drop down list.

  • Page 67: Verifying A Recording Schedule

    RECORDING SCHEDULE, CONTINUED 5.6.4 VERIFYING A RECORDING SCHEDULE 1. Select a single day of the week using the selection check box to the left of the specified day. 2. Next move down to the schedule grid. 3. Identify the schedule (or schedules) that have specific hours of the day high-lighted in light blue color.

  • Page 68: Sensor Setup

    SENSOR SETUP The Sensor Window options enable, disable, and configure Sensors. Sensor/Control Name Sensor Type Delay (sec) 5–24 Opens a menu to allow custom naming of controls and sensors for easy identification. Displays the sensor number Selects whether the Sensor will be Normally Open (NO) or Normally Closed (NC).

  • Page 69: Network Setup

    NETWORK SETUP CAUTION: Do not join this DVR to a Network Domain. Domains push across policies that can negatively affect the DVR. More importantly, by default, the user must press CTRL ALT DEL to login. This Keyboard combination is disabled and the software will not be able to load.
  • Page 70 Communication 5–26 The Center Port is the port used to connect to the Fusion Remote Software. This is the Port that must be specified inside the Fusion Remote software to connect to the DVR. If connecting through a firewall, this port must be opened to incoming and outgoing traffic.

  • Page 71: Administration

    Allows the log file to be exported in weekly increments. Deletes the selected log files. Displays information pertaining to Alarm Events. Displays information pertaining to User Logins, DVR reboots and other related information. Displays the Hardware Log file information which includes recording successes and failures.

  • Page 72: User Management

    The User Management Console has options for creating, editing, and deleting user accounts. Each user account can be assigned different privileges that limit their usage of the DVR system. Users can be given administrator privileges by enabling all rights, however only the true administrator account can log into the User Management...

  • Page 73: User Rank

    The User Ranking structure allows the option to assign a privilege system (1-10 where one has the most rights) to users of the DVR. For example. Since only one user is allowed to use the PTZ controls at any one time, an administrator with a higher rank can kick another user out and take control of the PTZ.

  • Page 74: Site Information

    Displays the software version on the DVR. A user-specified unique identification name that is used by other DVR software to connect to the DVR (Fusion Remote, Alarm Monitor, FVMS). Displays the serial number of the DVR. Displays the serial number of an internal hardware component inside the DVR.

  • Page 75: Ptz

    5.11 The PTZ Setup enables PTZ cameras, creates Presets, Tours, and adjusts speed settings. Many options listed here are features only available on selected cameras. Refer to the Advanced PTZ chapter in this manual for description on setting up a PTZ camera and PTZ options.

  • Page 76: Adjusting The Time, Date, And Time Zone

    My Computer to expand the folder tree. 3. Double-click Date/Time inside the Control Panel. 4. Adjust the date, time, and time zone. 5. When finished, close all open windows and restart the DVR unit by selection Start Shut Down.

  • Page 77: Central User Management (Optional)

    5.14 CENTRAL USER MANAGEMENT (OPTIONAL) The Fusion DVRs are capable of utilizing a Central User Management system. This option allows, from one location, the creation, deletion and management of user accounts on multiple DVRs. This makes managing a large amount of DVRs easy and organized.
  • Page 78 5.14 CENTRAL USER MANAGEMENT, CONTINUED Site Management User Management Log In Log Out Exit 5–34 This option will Add/Delete DVRs that are managed by the Central User Management Software. This option will Add/Delete/Modify User Accounts and User access privileges. Only the Administrator can modify settings. In order to open the Site Management or User Management options, the Administrator must login.

  • Page 79: Site Management

    IP Entry Field Site List Get Site Info Add Site Delete Site Used when adding a new DVR. This field accepts standard IP addresses. Display the current DVRs being managed by the Central User Management Software. Updates the information from each DVR.

  • Page 80: User Management

    The User Management Console has the ability to create, edit, and delete user accounts. Each user account can be assigned different privileges that limit their usage of the DVR system. Users can be given administrator privileges by enabling all rights, however only the true administrator account can log into the User Management Console.

  • Page 81: Select Site

    5.14.4 SETTING UP THE CENTRAL MANAGEMENT USER SERVER To set up a Central Management User Server follow these steps. 1. Install the Central Management User Software on a computer or DVR. 2. Run the software and open Site Management. (Logging in may be necessary) 3.

  • Page 82: Enabling A Dvr To Use Central User Management

    4. Enter the Server Port used by the Authentication Server. (Must be between 7000- 7100) 5. Enter a Site port that the DVR will use to communicate with the Authentication Server. (Must be between 6000-6100) 6. Press OK to save and close.
  • Page 83 5.15 TV OUTPUT CONTROL SETUP (OPTIONAL), CONTINUED Port Cameras Motion/Sensor Event Event Holding Time Auto Switching Time Enables the selected Port. Refers to the output channel. The Ports use RCA jacks. The camera buttons allow selection of cameras to sequence on the selected Port. This option allows immediate output of a Motion or Sensor Event on the selected Port.

  • Page 84: Customizing The Tv Outputs

    5.15 TV OUTPUT CONTROL SETUP (OPTIONAL), CONTINUED 5.15.1 CUSTOMIZING THE TV OUTPUTS To set up the TV OUTPUT CONTROLS follow these steps. 1. Select the TV OUT button from the General tab inside setup. 2. Select a Port (one of the 4 available output channels) to modify by selecting a Port from the Port dropdown box.

  • Page 85: Section 6 Search Options

    SEARCH OVERVIEW The DVR unit has several options that allow easy searching to find a particular section of video. From Motion and Sensor indexing to calendar views showing which days have recorded video, the DVR unit is equipped to quickly find what you’re seeking.
  • Page 86 SEARCH OVERVIEW, CONTINUED After Image Removal Search Options Exit Search Save/ Open File / Print Play Controls Slow / Fast Bright Zoom Search Date and Time Hour/Minute Control Select Date Audio Channels Camera 6–2 Often times, extensive motion can create a ‘digital blur’...

  • Page 87: Play Controls

    PLAY CONTROLS The Play Controls give the ability to play the video Frame by Frame, Normal Speed, and Reverse. Play Reverse Play (Normal Speed) Play (Frame by Frame) Stop Play Reverse (Frame by Frame) HOUR / MINUTE SELECTOR The Hour/Minute Control Bar allows a user to select the Hour and Minute using an easy-to-use slide bar.

  • Page 88: Brightness / Speed / Zoom

    BRIGHTNESS / SPEED / ZOOM The Brightness and Zoom features can get the most out of the images. Adjusting Brightness can brighten up an image to get more detail. Zoom can not only bring the image up full screen but also Zoom into a particular area of the image.

  • Page 89: After Image Removal

    When using the 720 x 480 resolution, two fields are mixed. Because of the timing gap between the two fields, according to the standardized image rules, after image might occur to high speed moving images. The Fusion DVR unit allows you to remove this by pressing the After Image Removal button.

  • Page 90: Search Options Overview

    Object Search: Status Search: PERFORMING A BASIC SEARCH There are several different types of searches that can be performed on the DVR unit. The most basic involves simply selecting the date, the time, the camera, and pressing play. 1. Select a date using the calendar.

  • Page 91: Daylight Savings Time

    However when the hour “falls back” there is a duplicated hour that under normal circumstances would be recorded over. The Honeywell Fusion DVR actually records both hours and allows you to select which hour to play if the need arises.

  • Page 92: Printing An Image

    6.11 ‘SAVE TO’ FUNCTION The DVR unit can export single images in the .JPG file format, save video clips in the .AVI format, or output to a VCR using the s-video port. The JPG and AVI file formats are extremely common with virtually universal computer support making them ideal formats to use.
  • Page 93 6.11 SAVE TO FUNCTION, CONTINUED Export Type AVI Duration Image Quality Analog Out Export Selects method used for export. Enter duration (in seconds) for recording the AVI file. Although 100 is the longest displayed, a manual time may be entered. It may be necessary to reduce the overall size of an AVI file;...

  • Page 94: Index Search

    6.12 INDEX SEARCH Using the Index Search can greatly decrease the amount of time spent searching through saved video. The Index Search allows a user to perform a search based on criteria such as Sensor, Motion and Instant Record events. Select All Cameras Multiple...
  • Page 95 6.12 INDEX SEARCH, CONTINUED Image Display Area Time Camera Number Type Search Results Where Search results images are displayed. Time of the result. Camera number of the returned result. Displays event type: M – Motion S – Sensor IR – Instant Record Displays the results of the search.

  • Page 96: Preview Search

    6.13 PREVIEW SEARCH The Preview Search can be used in a number of circumstances to quickly find an exact moment where an event, such as a theft, occurred. The Preview Search basically gives a 24 Hour visual overview of a single camera by separating a 24 hour period (1 day) into 24 images, one image for each hour of the day.

  • Page 97: Performing A Preview Search

    6.13 PREVIEW SEARCH, CONTINUED 6.13.1 PERFORMING A PREVIEW SEARCH 1. Select a single camera, either by turning off all cameras but one or by double- clicking a displayed image. 2. Select the Preview Search button. 24 images display. If there is no recorded video during a portion of the day, “No Image”...

  • Page 98: Object Search

    6.14 OBJECT SEARCH Object Search is a powerful Search utility that is used to search a region on the video for any motion changes. The Results are neatly displayed and can be viewed quickly. Search Results Search Information Cancel Stop Apply to Main Search Reload First Frame Clear Selection...

  • Page 99: Performing An Object Search

    6.14 OBJECT SEARCH, CONTINUED Start Sensitivity Key Frame Search Show Detected Image 6.14.1 PERFORMING AN OBJECT SEARCH 1. Select a single camera, either by turning off all cameras but one or by double- clicking a displayed image. 2. Select the Object Search button. 3.

  • Page 100: Status Search

    6.14 OBJECT SEARCH, CONTINUED 6. Adjust the sensitivity if necessary. 7. Click OK to begin the search. When results are found, they will be displayed in the column to the right. If no results are found, the search will end and “No Images Found”...

  • Page 101: Performing A Status Search

    6.15 STATUS SEARCH, CONTINUED Camera Hours Recording Block 6.15.1 PERFORMING A STATUS SEARCH 1. Select the Status Search button to open the Status Search window. 2. Use the mouse to click on an area of the blue recording block. Only one camera can be displayed at a time. 6.16 AUDIO Audio is played back at 48,000Hz.

  • Page 102: Point Of Sale (Optional)

    6.17 POINT OF SALE (OPTIONAL) The Point of Sale search is an optional component that can be added to the Fusion DVR. When installed and activated, a POS button will appear inside the Search Window. The POS functionality utilizes TVS technology. When performing a POS search, a TVS window appears allowing multiple options and criteria for detailed searches.

  • Page 103: Section 7 Pan / Tilt / Zoom

    PAN / TILT / ZOOM OVERVIEW The PTZ controls within the DVR unit allow for powerful control over the cameras. This can be extremely beneficial by increasing the usefulness of the recorded video. Use the PTZ controls to create custom preset configurations that can continuously sweep across large areas.
  • Page 104 7. Once enabled, the Protocol can be edited. Select the appropriate Protocol. NOTE: Protocols are a set of instructions written by the manufacture of the PTZ cameras that allow software programs such as this DVR to control their functions. The majority of the major PTZ manufacturer protocols are included in this software.

  • Page 105: Supported Protocols

    Computar Dong Yang Unitech (DRX-502A) Dennard Dynacolor Ernitec Fastrax II FilTech (DSC-230/PT-201) Fine System (CRR-1600) Focvision (KD1602) HMS-250 HSCP Honeywell (HSD-250) Inter-M(VRX-2101) Javelin (Orbitor) Kalatel (Cyber Dome) LG (LVC-A70x's) LG SD-110 LG (LPT-A100L) Merit LI-LIN NiceCam Panasonic Pelco D Pelco (P protocol 4800bps) Philips (TC8560 &...

  • Page 106: Advanced Ptz Setup

    FUSION DVR Digital Recording and Transmission System ADVANCED PTZ SETUP 7–4...
  • Page 107 Selects the current camera to be edited. Defines the specific settings to transmit to the PTZ. Enables the DVR to control the PTZ camera. Used to create Presets and Tours for the PTZ camera. Since each camera creates these in a different way, there can be multiple methods.

  • Page 108: Creating And Viewing Preset Positions

    CREATING AND VIEWING PRESET POSITIONS A Preset Position is a user-defined location where the camera can be pointed, zoomed in, and focused. Preset positions can be defined and labeled if the camera supports this. Each preset can have an independent Dwell and Speed setting for use with the Tour 2 Function.

  • Page 109: Viewing A Preset

    CREATING AND VIEWING PRESET POSITIONS, CONTINUED A window will open for entering a Preset Name. Enter a name and press OK. 7.4.2 VIEWING A PRESET 1. From the Main Display Screen, click on the PTZ camera to select it. 2. Using the keyboard, press the number keys corresponding with the Preset positions.
  • Page 110 UNDERSTANDING TOURS, CONTINUED Tour Method Preset Tour Preset Tour 2 Mimic Tour Pan Swing/ Tilt Swing Sequence Start/Stop Position Privacy Zone Travel Speed Dwell Time 7–8 These options define the type of Tour to use. The Preset Tour cycles through recorded Presets. For Ex. If Presets 1,2,4,6 and 9 are defined, then the Tour will cycle as such...

  • Page 111: Creating A Preset Tour

    UNDERSTANDING TOURS, CONTINUED 7.5.1 CREATING A PRESET TOUR 1. Start by creating two or more Preset Positions. (refer to Section 7.4.1) 2. Select the Preset Tour Method. The Preset Tour is now the default Tour method. 3. The Tour is now set to cycle through the defined presets. 7.5.2 VIEWING THE PRESET TOUR 1.

  • Page 112: Creating A Mimic Tour

    UNDERSTANDING TOURS, CONTINUED 7.5.5 CREATING A MIMIC TOUR 1. Select the Mimic Tour Method. 2. Press the Start Position button. 3. Using the PTZ Controller, move the PTZ in the path of the tour to mimic. 4. Press the Stop Position button when finished moving the PTZ around. 5.

  • Page 113: Ptz Status On Close

    PTZ STATUS ON CLOSE The PTZ Status on Close is an option that defines the default settings for a PTZ camera when the controller is not open. This includes activating a Tour, moving to a preset position or simply leaving the camera as it. Stay Put Start Tour Go To Preset...

  • Page 114: Ptz Address Setting

    ID addresses. This option is for setting the new RX address. This option is for specifying the PTZ ID address that the PTZ is set to. This option must be set correctly in order for the DVR to communicate with the PTZ. This option can be beneficial when large...

  • Page 115: Accessing Ptz Menu's

    Since every PTZ camera is different, the functions of these options can vary slightly. The Fusion DVR provides an easy way to access the cameras options. For explanations of what those options are please refer to the manual that came with your camera.

  • Page 116: Using The On-Screen Controller And Compass

    USING THE ON-SCREEN CONTROLLER AND COMPASS The Fusion DVRs provide control for the PAN/TILT camera in two different ways. 1. Using the Graphical PTZ controller that appears when the PTZ button is pressed on the main screen. 2. Clicking on the video itself. This second option is a much more powerful way to control the Camera.

  • Page 117: The Ptz Controller

    USING THE ON-SCREEN CONTROLLER AND COMPASS, CONTINUED 7.9.1 THE PTZ CONTROLLER Direction Controls Zoom Focus Iris Preset 1 Tour Preset 2 Tour Mimic Tour Camera Number Aux 1 Aux 2 Preset Controls There are 8 directions buttons that move the PTZ. NOTE: Only 4 of the buttons work for all protocols (UP, DOWN, LEFT, RIGHT).

  • Page 118: Aux Buttons

    USING THE ON-SCREEN CONTROLLER AND COMPASS, CONTINUED 7.9.2 AUX BUTTONS The AUX buttons activate different options for each protocol. The protocols and their options are defined below. VCL, Ademco Rapid Dome, Javelin (Orbitor), Pelco-D, Pelco-P, Kodicom Receiver, CBC, Dennard 7–16 AUX 1 Auto Iris AUX 2...

  • Page 119: Section 8 Backing Up To A Cd-R Drive

    1/3 the data to a CD, 1/3 the data to the local Drive and 1/3 the data to a network drive. DirectCD FORMAT UTILITY The Fusion DVR unit uses DirectCD® 5.0 to save the data to a CD-RW Drive. This allows the DVR to use the CD-RW just as it would any other attached Hard Drive, both reading and writing to it.
  • Page 120 Minimizes the window Closes the DirectCD application Use the dropdown box to choose the CD-RW drive attached to the DVR. Generally, this defaults to the correct CD-RW drive. Used to perform repairs on CDs that have become unstable or failed completely.

  • Page 121: Formatting A Cdr Or Cd-Rw Disc

    FORMATTING A CDR OR CD-RW DISC We strongly recommend using CDR discs rather than CD-RW discs. CD-RW discs can take up to 30 minutes or more to format and may have compatibility issues. 1. Insert a blank CDR or CD-RW disc into the CD-RW drive. 2.
  • Page 122 Format CD Quick Format IEEE (1394) Start Backup Eject CD Browse Network Drive Backup Order 8–4 Opens the CD formatting Utility (see the Formatting a CD-R or CD-RW section in this chapter). Performs a quick format of the attached IEEE (1394) device. Once the location and video have been selected, this button begins the backup process.
  • Page 123 GENERAL BACKUP OPTIONS OVERVIEW, CONTINUED Select Backup Media BV Copy Fixed HDD Backup Items Backup Space Select Day Displays available storage drives. Use this window to select the drive you wish to save video files to. Copies the proprietary viewer onto the CD-R and makes the CD autoplay.

  • Page 124: Scheduled Backup Options Overview

    SCHEDULED BACKUP OPTIONS OVERVIEW The SCHEDULED BACKUP OPTIONS window allows the creation of a scheduled daily backup of selected times to a specified storage location. Available storage locations exclude CD-R and CD-RWs and are limited to hard disks NOTE: specifically identified as backup space (see the specifying scheduled backup drives section in this chapter).

  • Page 125: Specifying Scheduled Backup Drives

    SPECIFYING SCHEDULED BACKUP DRIVES In order to use the Scheduled Backup feature one or more storage drives or partitions connected to the DVR must be labeled as a backup drive. 1. Exit and restart in Windows mode. 2. Double click the My Computer icon on the DVRs desktop. A file menu will be displayed.

  • Page 126: Backing Up To A Cd-Rw Drive Or Hard Drive

    BACKING UP TO A CD-RW DRIVE OR HARD DRIVE 1. From the Main Display Screen select the BACKUP button. The Backup Options window displays. 2. From the Backup Options window, use the calendar to select a date. 3. Select the time(s) to backup by clicking on the desired blocks. The blocks will turn red when selected.

  • Page 127: Removing The Disc From The Cd-Rw Drive

    7. Select the Leave As Is option to continue using the CD for future backups by the DVR unit. The disk may not be able to read in other CD-ROM drives if this is selected. Select the Close To UDF v 1.5 to view the data in standard CD-ROM Drives.
  • Page 128 FUSION DVR Digital Recording and Transmission System NOTES: 8–10...

  • Page 129: Section 9 Lan / Isdn / Pstn Connections

    Since connecting the DVR unit to a network can be extremely complex (depending on the network), this Fusion DVR manual will cover only the basics. It is suggested that you consult your Vendor or IT Administrator before attempting to create or connect to a LAN.

  • Page 130: Connecting The Dvr To A Lan

    Administrator for appropriate IP settings. Example: NOTE: In order to connect to the DVR unit through a remote LAN connection, a static IP address must be assigned. If the network assigns the IP address automatically (DHCP), contact the Network Administrator for help assigning a static IP address.

  • Page 131: Section 10 Digital Signature Verifier

    Included on the Software Installation CD supplied with the DVR unit is the Digital Signature verification program. This program can be installed on any computer and simply loads an image in question 10.2...

  • Page 132: Using The Digital Verifier

    10.2 INSTALLATION, CONTINUED 3. When the Setup Complete window appears select Finish. Setup is now complete. 10.3 USING THE Digital Verifier 1. Open the Digital Signature verification program by selecting Start Programs Verifier. 10–2 FUSION Digital Signature Verifier Digital Signature...
  • Page 133 2. Select the Browse button to load the JPG or AVI file. 3. Enter the Site Code of the DVR unit that the image was originally extracted from. 4. Click the Verify button to continue or Close to close the window without verifying.
  • Page 134 FUSION DVR Digital Recording and Transmission System 10.3 USING THE DIGITAL VERIFIER, CONTINUED 10–4...

  • Page 135: Section 11 Proprietary Viewer

    This video cannot be read by any other viewer. The Proprietary Viewer is essentially the Search portion of the DVR software. For detailed explanation of these functions, refer to Section 6.

  • Page 136: Installing The Proprietary Viewer

    11.2 INSTALLING THE PROPRIETARY VIEWER 1. Insert the Software Installation CD into the CD-ROM. (Do not install on the DVR unit.) 2. Select the Proprietary Viewer option to begin installation. When the Welcome screen appears, select Next. 3. When the Choose Destination Location window appears select Next.
  • Page 137 11.2 INSTALLING THE PROPRIETARY VIEWER, CONTINUED 4. When the Select Program Folder window appears select Next. 5. Select either 16 or 32 channel option depending on the Model you have. You can always reinstall and change this option at a later date. Press Next. 11.2 INSTALLING THE PROPRIETARY VIEWER, CONTINUED If you have purchased the TVS POS Remote option from TVS then select the YES 11–3...
  • Page 138 FUSION DVR Digital Recording and Transmission System option. Otherwise select the NO option. Press Next. 6. When this window appears select Finish. Setup is now complete. 11–4...

  • Page 139: Loading Vide0 From Cd-Rom Or Hard Drive

    11.3 LOADING VIDE0 FROM CD-ROM OR HARD DRIVE 1. Open the Proprietary Viewer program by selecting Start Proprietary Viewer Proprietary Viewer. 2. Select Backup Search (see Section 6.7 – Performing a Basic Search) and the Choose time to Search window opens.
  • Page 140 FUSION DVR Digital Recording and Transmission System NOTES: 11–6...

  • Page 141: Section 12 Alarm Monitor

    The Alarm Monitor software is a utility that streams video across a Local Area Network to a Client PC when an alarm is detected on the DVR unit. The video that streams across can be stopped, played forwards and backwards, in slow motion or real speed.

  • Page 142: Configuring The Dvr

    FINISH. 12.3 CONFIGURING THE DVR To enable the Alarm Monitor on the DVR follow these steps: Enter SETUP and click the Recording Schedule tab. Assign the desired sensors to the desired cameras. Refer to the Recording Schedule section of this manual for in depth instructions on how to do this.

  • Page 143: Configuring The Client Pc

    Alarm Monitor Window section later in this chapter. Open the Alarm Monitor window on the Client PC. Start >Programs > Fusion > Alarm Monitor > Alarm Monitor Click New in the DVR List and enter the site code, site name, and IP...

  • Page 144: Alarm Monitor Window

    Zoom in or out of the displayed video or reset to default. Displays the Video feed coming from the DVR. Lists all DVR units you have connected to the Alarm Monitor. Individual DVR unit in DVR List with displayed settings.

  • Page 145: Event List Right Click

    Lists all recorded events matching the Date, Event, and DVR settings. Displays a preview image of all recorded events matching the Date, Event, DVR, and Filter settings. Sets an alarm event to Default. Sets an alarm event to Reviewed. Sets an alarm event to Dismissed.

  • Page 146: Search Alarm Window

    12.6 SEARCH ALARM WINDOW Comment AVI File Export Quality Export Options Export Alarm Event Information Display Playback Controls Display Previous Alarm Continuous Playing Next Alarm 12–6 Provides space for user to add comments to video events. When selected a video clip exported when Export is clicked.

  • Page 147: Configuration Window

    Alarm Monitor receives an event. Indicates the port which the Alarm Monitor uses to listen for incoming events. This number should be changed to the same number as is set in the Emergency Port in Communication Settings on the DVR. 12–7...
  • Page 148 FUSION DVR Digital Recording and Transmission System NOTES: 12–8...

  • Page 149: Section 13 Remote Software

    The DVR unit was specifically designed to be fully operated and maintained remotely. It connects using the standard TCP/IP protocol thorough connection types such as DSL, Cable Modem, T1, ISDN, 56K Modem, LAN, and more. The Fusion Remote software provides for viewing live video, searching through archived video, exporting images and video clips;...

  • Page 150: Remote Client Minimum Requirements

    13.1 FUSION REMOTE SOFTWARE OVERVIEW, CONTINUED 13.1.1 REMOTE CLIENT MINIMUM REQUIREMENTS • Pentium 233 or equivalent • 32MB System Memory • DirectX 8 or higher • Compatible video card (ATI Preferable) • Internet or LAN Connection (56K, DSL, Cable Modem, T1, ISDN, etc.) •...

  • Page 151: Setting Up The Server To Accept Incoming Connections

    DVR server. Specifies a value (in seconds) to wait for a signal from the Fusion Remote Client. If a signal is not received by that time, the connection is dropped. Used by the DVR to transfer the connection data.

  • Page 152: Setting Up The Fusion Remote Software

    SETTING UP THE FUSION REMOTE SOFTWARE 13.3.1 INSTALLING THE FUSION REMOTE SOFTWARE 1. On the Client computer, insert the Honeywell Fusion Software CD into the CD-ROM. The CD should play automatically. 2. When prompted, select the Install Fusion Remote Software option.
  • Page 153 13.3 SETTING UP THE FUSION REMOTE SOFTWARE, CONTINUED 2. Press New to open the Site Detail Information window. 3. Enter the Site Code and Site Name. The Site Code will be the name displayed inside the connection box to help identify the unit.
  • Page 154 FUSION DVR Digital Recording and Transmission System NOTES: 13–6...

  • Page 155: Section 14 The Web Viewer

    Microsoft Internet Explorer. In order to log in to the DVR server, a user account must be made for the user. This ensures that only authorized users are allowed to log in. In addition, each user can be assigned different privileges that allow them or deny them access to different functions.

  • Page 156: Configuring The Dvr Server To Accept Remote Connections

    If a message is received saying your Internet Explorer® security settings do not allow for downloading Active X components then adjust the browser security settings. One way to do this is to add the IP address of the DVR to your trusted sites list inside Internet Explorer® settings. Contact the System administrator for additional help with adjusting Internet Explorer®...

  • Page 157: Closing The Web Viewer

    14.1 WEB VIEWER OVERVIEW, CONTINUED 6. A login window will appear. Enter a Username and Password that is authorized to access the DVR. 7. The cameras will now be displayed. 14.1.3 CLOSING THE WEB VIEWER 1. To exit the Web Viewer simply close Internet Explorer®.
  • Page 158 FUSION DVR Digital Recording and Transmission System NOTES: 14–4...

  • Page 159: Section 15 Technical Specifications

    TECHNICAL SPECIFICATIONS 15.1 HFDVR FUSION 8-CHANNEL Storage (Hard Drive) Storage MAX Operating System Viewing Rate Recording Rate (240 IPS) Recording Rate (480 IPS) Digital Control Output Sensor Input Resolution Image Compression Average File Size Video Inputs Looping Outputs Composite Outputs...

  • Page 160: Hfdvr Fusion 16-Channel

    15.2 HFDVR FUSION 16-CHANNEL Storage (Hard Drive) Storage MAX Operating System Viewing Rate Recording Rate (240 IPS) Recording Rate (480 IPS) Digital Control Output Sensor Input Resolution Image Compression Average File Size Video Inputs Looping Outputs Composite Outputs Video Outputs...

  • Page 161: Hfdvr Fusion 32-Channel

    15.3 HFDVR FUSION 32-CHANNEL Storage (Hard Drive) Storage MAX Operating System Viewing Rate Recording Rate (240 IPS) Recording Rate (480 IPS) Digital Control Output Sensor Input Resolution Image Compression Average File Size Video Inputs Composite Outputs Video Outputs Max FPS Per Channel...
  • Page 168 TEL +31–299–419–000 All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof.

Table of Contents