Sharp AR-M208 Service Manual page 27

[7-seg LED display]
1: Self print (2-by-4) mode
2: Grid print mode
Pressing the [START] key makes a print by 2 by 4 mode. After comple-
tion of printing, the menu returns to the initial menu.
Pressing the [CA] key cancels the simulation mode.
(Input screen) (Executing screen)
67
67-11
Purpose Setting
Function (Purpose) Used to set the Select-IN signal.
Operation/procedure (Pattern 1)
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Sim67-11 SELECT-IN
SELECT-IN SIGNAL 0
(0:ON 1:OFF)
[ 0- 1] 0
Setting range 0-1
Default 0
* Execution is inhibited until GDI or PCL board is securely installed.
(Because the board is detected by the software.)
Note: Executable only when the PCL is installed.
67-14
Function (Purpose) Used to check write/comparison of flash
programs.
Operation/procedure
Download PCL.
Pressing the [OK] key displays "Please Send Data" "Ready" and the
data is sent from the PC under the MS-DOS command of FCOPY and
the file name.
Used to overwrite and check the flash device while displaying its pro-
cess status.
After completion, the result is displayed.
(It takes a little time to display READY.)
(1) (2)
Sim67-14 FLASH D/L Sim67-14 FLASH D/L
PRESS OK KEY Please Send Data
READY
(Normal end screen) (Abnormal end screen)
Sim67-14 FLASH D/L Sim67-14 FLASH D/L
COMPLETE FAILED
(3)
Sim67-14 FLASH D/L
PROGRAM
RECEIVE
AR-M208 SIMULATION 8 - 13
(Flash Device) (Processing state)
PROGRAM RECEIVE
BOOTROM ERASE
PS KANJI FONT WRITE
ESC/P KANJI FONT VERIFY
OPTION FONT
Press the [CA] key to cancel the simulation and reset.
* Execution is inhibited until GDI or PCL board is securely installed.
(Because the board is detected by the software.)
Note: Executable only when the PCL is installed.
67-17
Function (Purpose) Used to clear NVRAM.
Operation/procedure (Pattern 7)
Pressing the [OK] key displays the confirmation message.
Press the [OK] key again to clear. Press the [BACK] key to interrupt
clearing.
If there is no abnormality after Clear operation, "COMPLETE" is dis-
played. If there is any abnormality, "ERROR" is displayed.
(Initial screen) (Process check screen) (Executing screen)
Sim67-17 NVRAM CLR.
Sim67-17 NVRAM CLR.
NVRAM CLEAR
NVRAM CLEAR
ARE YOU SURE?
PRESS OK KEY
(Normal end screen) (Abnormal end screen)
Sim67-17 NVRAM CLR. Sim67-17 NVRAM CLR.
NVRAM CLEAR NVRAM CLEAR
COMPLETE ERROR
PRESS OK KEY PRESS OK KEY
* Execution is inhibited until GDI or PCL board is securely installed.
(Because the board is detected by the software.)
Note: Executable only when the PCL is installed.
67-18
Function (Purpose) Used to clear the data area for FLASH ROM
Network Scanner Application.
Operation/procedure (Pattern 7)
Pressing the [OK] key displays the confirmation message.
Press the [OK] key again to clear. Press the [BACK] key to interrupt
clearing.
If there is no abnormality after Clear operation, "COMPLETE" is dis-
played. If there is any abnormality, "ERROR" is displayed.
(Initial screen) (Process check screen) (Executing screen)
Sim67-18 APP. CLR.
Sim67-18 APP. CLR.
APP. DATA CLEAR
APP. DATA CLEAR
ARE YOU SURE?
PRESS OK KEY
(Normal end screen) (Abnormal end screen)
Sim67-18 APP. CLR. Sim67-18 APP. CLR.
APP. DATA CLEAR APP. DATA CLEAR
COMPLETE ERROR
PRESS OK KEY PRESS OK KEY
* Execution is inhibited until GDI or PCL board is securely installed.
(Because the board is detected by the software.)
Note: Executable only when the PCL is installed.
Sim67-17 NVRAM CLR.
NVRAM CLEAR
NOW DOING...
Sim67-18 APP. CLR.
APP. DATA CLEAR
NOW DOING...