Sharp AR-M208 Service Manual page 21

Error code Name
SPF paper-in
PI_TOP
lead edge jam
SPF paper-in rear
PI_END
edge jam
SPF duplex
JAM_REV
reversion jam
SPF paper-out
PO_TOP
lead edge jam
SPF paper-out
PO_END
rear edge jam
SPF long size
ORG_LONG
error
ORG_SHORT SPF short size
error
24
24-15
Purpose Data clear
Function Used to clear the scanner mode counter.
(Purpose)
Item Counter
Operation/procedure
Press the [OK] key.
The scanner mode counter and the number of send of the scanner are
cleared.
(Initial screen) (Process check screen)
Sim24-15 COUNTERCLR
Sim24-15 COUNTERCLR
SCANNER MODE
SCANNER MODE
COUNTER CLEAR
COUNTER CLEAR
PRESS OK KEY ARE YOU SURE?
* Execution is inhibited until GDI or PCL board is securely installed.
(Because the board is detected by the software.)
25
25-1
Purpose Operation test/check
Function Used to check the operation of the main drive
(Purpose) (excluding the scanner section) and to check the
operation of the toner concentration sensor. (The toner
concentration sensor output can be monitored.)
Section DRIVE
Item Operation
Operation/procedure
The operation of the drive system is checked.
Toner density control sensor value is displayed.
Select the mode with the 10-key and press the [OK] key, and the main
motor will rotate and the toner concentration control sensor value will
be displayed.
Paper Reached/
Sensor name Not reached to
Sensor
SPF P-IN sensor Not reached
SPF P-IN sensor Reached
SPF P-IN sensor Not reached
(paper after
reversion)
SPF P-IN sensor Reached, P-
OUT not
reached
SPF P-OUT Reached, P-IN
sensor is passed (OFF).
SPF P-OUT Reached
sensor
SPF P-IN sensor Reached
SPF P-IN sensor Pass (OFF at
JAM)
AR-M208 SIMULATION 8 - 7
After execution, interruption cannot be made for about 7 sec. ([CA] key,
[INTERRUPT] key, and [BACK] key are invalid.)
(Initial screen) (Executing screen)
Sim25-1 MAIN MOTOR Sim25-1 MAIN MOTOR
1:600dpi 1:600dpi
2:1200dpi 2:1200dpi
EXEC 2
* 1200dpi: Disabled
* Even though in toner END, if no other error (including cover open)
occurs after supplying power, execution of this command is allowed.
26
26-6
Purpose Setting
Function (Purpose) Used to set the specifications depending on
the destination.
Item Specifications
Operation/procedure
Select the destination.
Sim26-6 DESTINATION
DESTINATION 0
(0:JAPAN 1:SEC
2:SECL 3:SEEG 4:SUK
1/3 [ 0- 13] 0
Display
Content
items
Japan
0:JAPAN
SEC
1:SEC
SECL
2:SECL
SEEG
3:SEEG
SUK
4:SUK
SCA
5:SCA
SEF
6:SEF
EX inch series
7:INEG
EX AB series
8:ABEG
EX inch series (FC)
9:INEF
EX AB series (FC)
10:ABEF
China
11:CHINESE
Taiwan
12:TAIWAN
SEEG2
13:SEEG2
26-12
Function Used to input the Software Key for E-MAIL RIC.
(Purpose)
Operation/procedure
The current setup is displayed with ON or OFF.
Enter an input (20 digits) of the E-MAIL RIC soft key and press the
[OK] key, and the collating result is displayed with OK or NG.
(Initial screen) (In case of OK)
Sim26-12 E-MAIL KEY
Sim26-12 E-MAIL KEY
E-MAIL KEY
E-MAIL KEY ON
----------
----------
----------
----------
After canceling the simulation, if OK, the E-MAIL RIC function is
enable; if NG, the E-MAIL RIC function is disabled.
This setting must be reset after the simulation cancel.
* Execution is inhibited until GDI or PCL board is securely installed.
(Because the board is detected by the software.)
Note: Executable only when the PCL/NIC is installed.
[128]
EXEC 1
Destination
Setting
Default
range
0-13 0
(In case of NG)
Sim26-12 E-MAIL KEY
OK
E-MAIL KEY
----------
----------
NG