Page 1: Table Of Contents
Table of Contents Table of Contents Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo cassette with CD AM/FM stereo with CD Rear seat controls Rear seat entertainment system Navigation system Climate Controls Electronic automatic temperature control Lights Headlamps Turn signal control...
Page 2 Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Driving Starting Brakes Air suspension Transmission operation Vehicle loading Trailer towing Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Jump starting Wrecker towing...
Page 4: Introduction
For more information on Ford Motor Company and its products visit the following website: • In the United States: www.ford.com •...
Page 5 Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol.
Page 6 This information may be stored during regular operation or in a crash or near crash event. This stored information may be read out and used by: • Ford Motor Company. • service and repair facilities. • law enforcement or government agencies.
Page 7 Introduction Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. Please read the section Supplemental Restraint System (SRS) in the Seating and safety restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury. Front seat mounted rear facing child or infant seats should NEVER be used in front of a passenger side air bag unless the air bag can be and is turned OFF.
Page 8: Vehicle Symbol Glossary
Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation Child Seat Lower Warning Anchor Child Seat Tether Brake System Anchor Brake Fluid -...
Page 9 Introduction Vehicle Symbol Glossary Power Windows Power Window Lockout Front/Rear Interior Luggage Child Safety Door Compartment Release Lock/Unlock Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, Battery Acid or Sparks Explosive Gas Fan Warning Maintain Correct Fluid...
Page 10: Instrument Cluster
Instrument Cluster Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Page 11 Instrument Cluster If the light remains on, have your vehicle serviced at the first available opportunity. Note: The light will illuminate if vehicle refueling is conducted with the engine running. Never refuel vehicle with the engine running. Light is blinking: Engine misfire is occurring which could damage your catalytic converter.
Page 12 Instrument Cluster position to the START position, the light will momentarily illuminate just prior to reaching the START position). If the light remains on, continues to flash or fails to illuminate, have the ABS serviced immediately. If the ABS light remains on, it means the anti-lock brake system has malfunctioned and is disabled, however, the normal brake system will still function unless the brake warning light also remains illuminated and parking brake is off.
Page 13 Instrument Cluster Speed control Illuminates when the speed control is activated. Engine coolant temperature Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as safely possible, switch off the engine and let it cool. Never remove the coolant recovery cap while the engine is running or hot.
Page 14 Instrument Cluster Four wheel drive low (if equipped) Illuminates when four-wheel drive low is engaged. If the light continues to flash have the system serviced. Four wheel drive high (if equipped) Illuminates when four-wheel drive is put in high range. If the light HIGH continues to flash have the system serviced.
Page 15: Gauges
Instrument Cluster GAUGES RPM X 1000 HIGH km/h BRAKE Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating.
Page 16 Instrument Cluster Fuel gauge Displays approximately how much fuel is in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade. When refueling the vehicle from empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel.
Page 17 Instrument Cluster Trip odometer Registers the kilometers (miles) of individual journeys. Press and release the message center INFO button until TRIP mode appears in the display. Press the message center RESET button to reset. Tachometer Indicates the engine speed in revolutions per minute.
Page 18: Entertainment Systems
Entertainment Systems Entertainment Systems PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD 1. EJ (Eject): Press to stop and eject a tape. 2. EJ (Eject): Press to stop and eject a CD. 3. BASS: Allows you to increase or decrease the audio system’s bass output.
Page 19 Entertainment Systems 4. BAL (Balance): Allows you to shift speaker sound between the right and left speakers. Press BAL then press SEL to shift sound to the left or right FADE: Allows you to shift speaker sound between the front and rear speakers.
Page 20 Entertainment Systems In CD mode, REW control reverses the CD within the current track. FF (Fast Forward): Works in tape and CD modes. In the tape mode, tape direction automatically reverses when the end of the tape is reached. In CD mode, FF advances the CD within the current track. 10.
Page 21 Entertainment Systems 11. AUTOSET: Press to set first six strong stations into AM, FM1 or FM2 memory buttons; press again to return to the original preset stations. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Page 22: Am/Fm Stereo With Cd
Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 23 Entertainment Systems 2. REW (Rewind): Press for a slow rewind, press and hold for a fast rewind. FF (Fast forward): Press for a slow advance, press and hold for a fast advance. 3. DSP (Digital Signal Processing): Your vehicle will have one of the following Digital Signal Processing (DSP) features: •...
Page 24 Entertainment Systems 6. BASS: Press BASS; then press to decrease/increase the bass output. TREB (Treble): Press TREB; then press SEL decrease/increase the treble output. 7. SEL (Select): Use with Bass, Treble, Balance and Fade controls to adjust levels. Use with MENU to engage RDS.
Page 25 Entertainment Systems The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend that FM radio broadcasters use RDS technology to transmit information. FM radio stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired. •...
Page 26 Entertainment Systems Speed sensitive volume (if equipped): Automatically changes the volume with vehicle speed to compensate for road and wind noise. The recommended level is 1–3. Level 0 turns the speed sensitive volume off and level 7 is the maximum setting. To engage the speed sensitive volume feature, press and hold the volume control for five seconds (with the radio on).
Page 27: Rear Seat Controls
Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 28 Entertainment Systems To activate Dual Play mode (rear - VOLUME + seat passengers listen to a different MODE playing media than the front seat passengers): SEEK MEMORY • Press the speaker/headphone control. • Press the MODE control to change audio sources (for headphone mode only) •...
Page 29 Entertainment Systems Turning the rear speakers on and off Press the headphone/speaker - VOLUME + control to turn the rear speakers on MODE (Single Play mode) or off (Dual Play mode). SEEK MEMORY Using headphones/Dual Play mode Plug a 3.5 mm headphone (not included) into the jack.
Page 30 Entertainment Systems Memory preset control Push the MEMORY control - VOLUME + successively to allow rear seat MODE passengers to scroll through the 6 memory presets in AM, FM1 or FM2. SEEK MEMORY Push the MEMORY control in CD mode (if equipped) to advance to the next disc.
Page 31 Entertainment Systems RADIO FREQUENCIES AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz RADIO RECEPTION FACTORS There are three factors that can affect radio reception: •...
Page 32: Rear Seat Entertainment System
Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 33 Entertainment Systems DVD player controls 1. MAIN control • NEXT — Press to access the next track on the CD, the next chapter on the DVD, or to go up in cursor mode. • PREV — Press to access the previous track on the CD, the previous chapter on the DVD, or to go down in cursor mode.
Page 34 Entertainment Systems 7. Auxiliary jacks Insert lines for standard video game players. 8. STOP/EJECT control Press once to stop DVD play. Press again to eject the DVD. 9. DISPLAY (DISP) control Press to enable on screen display of player menu and user display adjustments.
Page 35 Entertainment Systems • Press the FWD control to move the cursor right one position NEXT PREV Next/Previous control The NEXT (up) and PREV (down) controls allow you to access the NEXT next or previous track on a CD or PREV chapter on a DVD.
Page 36 Entertainment Systems FWD or REV control for slow motion playback. Three different speeds are available depending on how long the control is held. Press the control once for slow motion playback. Press the control again to disengage slow motion playback. Press the PLAY/PAUSE control to return to normal playback mode.
Page 37 Entertainment Systems 2. FAST FORWARD control Press to advance the direction of the DVD movie. 3. PLAY/STOP control Press to play or stop the DVD movie. 4. SEEK control Press to reverse or advance the chapter of the DVD or the track of the 5.
Page 38 Entertainment Systems Parental control To enable or disable your Rear Seat Entertainment DVD System, simultaneously press the memory preset controls 3 and 5 on the radio face. For further information about the Rear Seat Controls, refer to Rear Seat Controls section in this chapter. Wireless headphones Your system is equipped with 2 sets of wireless headphones.
Page 39 Entertainment Systems Wireless headphone operation To operate the headphones: • Press the ON/OFF button on the left-hand earpiece. The LED light on the right-hand earpiece will illuminate. Press again to turn off. • Adjust the headphones to comfortably fit your head. •...
Page 40 Entertainment Systems 1. 7.0” (diagonal) active matrix liquid crystal display (LCD) screen. 2. Screen housing. 3. Dimmer switch. Press +/- to increase/decrease the brightness of the screen. Playback and format • The DVD player of your Rear Seat Entertainment DVD System can only be used in the “playback”...
Page 41 DVDs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford DVD/CD players. Irregular shaped discs, discs with a scratch protection film attached, and discs with homemade paper (adhesive) labels should not be inserted into the player.
Page 42 Entertainment Systems Playing a video game/auxiliary device 1. Connect the video line from your video game device to the YELLOW auxiliary input jack. 2. Connect the left and right audio lines to the WHITE and RED auxiliary input jacks respectively. 3.
Page 43 Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford Lincoln Mercury could void user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 44 Entertainment Systems However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help.
Page 45: Navigation System
Entertainment Systems Foreign substances Exercise care to prevent dirt and foreign objects from entering the DVD player compartment. If liquid is accidentally spilled onto the system, immediately turn the system OFF and consult a qualified service technician. Cleaning compact discs Inspect all discs for contamination before playing.
Page 46 Entertainment Systems 1. VOL-PUSH: Press to turn the system ON/OFF. Turn to adjust the audio volume level. 2. AUDIO: Press to enter audio mode and access radio, CD, CDDJ, DVD (if equipped) settings. 3. MAP: Press to enter map mode and view your current vehicle position on the map.
Page 47 Entertainment Systems 3. Select AM, FM1 or FM2. 4. Press TUNE to adjust manually up ( ) or down ( ) the frequency band. 5. Press SEEK to find the next strong station up ( ) or down ( Note: If PTY (program type) is selected, the station selection will be limited.
Page 48 Entertainment Systems To use the Navigation system: 1. Ensure that the vehicle ignition is on, and the navigation DVD is loaded into the navigation DVD player. Refer to Loading the map DVD for navigation DVD locations. 2. Press DEST. The warning screen will appear. After reading, press AGREE.
Page 49 Entertainment Systems To adjust the voice guidance volume: Press On/Off to turn the voice guidance option on/off. Use the numeric keys (1–7) to determine the volume level of the guidance voice prompts. Voice activated commands (if equipped) Your Lincoln Navigation System (LNS) may be equipped with a voice activated feature which allows you to “speak”...
Page 50 Entertainment Systems While in navigation map mode, the following commands are available by voice activation: • Gas station • Gas • Hospital • Police station • Restaurant • Hotel Audio mode Your Lincoln Navigation Audio System has many features including a full range of audio functions.
Page 51 Entertainment Systems Speed compensated volume (SCV) With this feature, radio volume changes automatically with vehicle speed to compensate for road and wind noise. To engage the SCV feature: 1. Press AUDIO. 2. Press SOUND. SOUND SEEK TUNE AUTO SET SCAN PRESET SCAN TRAFFIC INFO...
Page 52 Entertainment Systems The AM/FM control works in radio, CD and navigation modes. AM/FM select in radio mode Press AM/FM1/FM2 to switch between AM/FM1/FM2 memory preset stations. AM/FM select in CD mode Press to stop CD play and begin radio play. AM/FM select in navigation mode The radio will continue to play in the background of the navigation screens.
Page 53 Entertainment Systems Bass : Allows you to increase or decrease the audio system’s bass output. Treble : Allows you to raise or lower the audio system’s treble output. Fade : Allows you to adjust the amount of sound emitted from the front and rear speakers.
Page 54 Entertainment Systems Seek • Press to find the next listenable station up/down the frequency band. • Press to advance to the next/previous track on a CD. Tune adjust Press TUNE to manually move down/up ( ) the frequency band. In CD mode, press TRACK to select the previous/next ( Autoset memory preset Autoset allows you to set strong radio stations without losing your...
Page 55 Entertainment Systems If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available. To deactivate autoset and return to your audio system’s manually set memory stations, press the AUTO SET again. Scan Press SCAN for a brief sampling of SOUND...
Page 56 Entertainment Systems Traffic function Select TRAFFIC for traffic SOUND information broadcast from certain SEEK TUNE stations which will automatically AUTO SET SCAN PRESET SCAN interrupt radio or CD playback at a preset volume level. TRAFFIC INFO SET PTY 87.9 89.9 98.1 98.5 106.3...
Page 57 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 58 Entertainment Systems Playing a previously loaded CD: To begin CD play (if a CD is already SOUND loaded), press AUDIO hard button SEEK TUNE and then CD. AUTO SET SCAN PRESET SCAN TRAFFIC INFO SET PTY 87.9 89.9 98.1 98.5 106.3 107.9 Press CD.
Page 59 Entertainment Systems 5. To load more than one disc, press and hold LOAD. This will initiate autoload and will allow you to load all open CD slots. After an allotted time, the screen will close automatically or you may press CD OPEN CLOSE on the bezel again. 6.
Page 60 Entertainment Systems Shuffle feature in CD mode When in CD (or CDDJ mode), press SHUFFLE to engage the shuffle feature. Press to select from shuffling between tracks (SHUFFLE TRACK) on the current CD or between all tracks on all CDs (SHUFFLE DISC).
Page 61 Entertainment Systems Map mode Map display information To access the map display, press MAP on the bezel. Once pressed, the current map display will appear on the screen showing the current vehicle location. Zoom control When ’Zoom’ is pressed, the scale indicator is shown on the screen. The scale markings are: 1/32, 1/16,1/4, 1/8, 1/2, 1, 2, 4, 8, 16, 32, 64, 128 miles.
Page 62 Entertainment Systems Additional map function buttons To initiate the display of additional map function buttons, tap the map anywhere on the screen. The following buttons will appear: • STORE - stores current vehicle location as a memory point. Refer to Memory Points for further information.
Page 63 Entertainment Systems Destination symbol — Indicates the current route destination. Next turn symbol — Shows the next maneuver that will need to be taken on the current route. North up button — Indicates that the map is displayed with north to the top of the screen.
Page 64 Entertainment Systems Home position symbol — Indicates the location on the map, currently stored as the home position. Stored location symbol — Indicates the location of a memory point. This is the default symbol used when the point is stored. (If desired, an icon of your own choice can be selected from the 15 icons available.) Refer to Choosing from the icon list.
Page 65 Entertainment Systems Route options (destination entered) Once in navigation mode and a route is currently active, press “Chng. route” to access the ROUTE OPTIONS screen. Choose from the following selections: • Detour: Press to select a detour around the current route. Refer to Detour options later in this chapter for further information.
Page 66 Entertainment Systems Route preferences After entering a destination, the Route options will appear on the screen showing what is currently selected. You may choose to activate/deactivate selections which the system will factor in when calculating your route. Those options are: •...
Page 67 Entertainment Systems Average speed settings Allows you to set approximate speeds you drive. These speeds enable the navigation system to aid in calculating timing for routes. Quick POI (Point of Interest) Allows you to change the Quick POI menu settings. Select the desired Quick POI (Gas, ATM, etc.) and then press ’List Categories’...
Page 68 Entertainment Systems Calibration This feature is helpful if the car has been towed, or if you notice it is not registering at the correct vehicle location on the map. Press “Position” to reposition the vehicle location. Press the screen to scroll the map to the desired location and press OK to confirm.
Page 69 Entertainment Systems • Time to destination (Show or Hide) Stored locations The Stored locations screen will allow you to choose from destinations that have been saved into the navigation system. In this screen, you can select from Memory Points, Special Memory Points, Home, Avoid Area, Destination and Way Point, or Previous Destination.
Page 70 Entertainment Systems On route scroll The system automatically scrolls through the entire planned navigation route either forwards or backwards. To activate, press the arrow buttons at the bottom left of the map screen. Voice guidance/volume Allows you to turn the voice guidance option on/off and to determine the volume level of the guidance voice prompts.
Page 71 Entertainment Systems Initial map display After pressing AGREE to the initial WARNING screen, you will move into the initial map screen which shows the current vehicle location. Pressing the globe icon will take you to the user settings — audible feedback, navigation units, language and clock.
Page 72 Entertainment Systems Ensure that you follow highway code restrictions and do not take any risks. For example, if you are unable to make a U-turn, continue on your journey. The navigation system will recalculate your route to get you back to an appropriate road to your destination. Destination entry Selecting a destination Press DEST to set a destination.
Page 73 Entertainment Systems Search area Your navigation system uses a regional search area. This area is the area from which navigational directions will be used. To check your area or reset, press CHANGE under the search area listing. The map will open and allow you to select another regional area.
Page 74 Entertainment Systems Deleting previous destination • Press “Delete”. The list of previous destinations is displayed showing “Delete Previous Destination” at the top of the screen. • Select (touch) the entry to be deleted. The item details will be listed. • Press YES to confirm the deletion.
Page 75 Entertainment Systems Adding a memory point • Once in the Store Memory Point Menu, press ADD. • Select (touch) the desired menu item. • Enter/select any required details. The new point will be added to the stored list of memory points. To give the new memory point a name: •...
Page 76 Entertainment Systems Choosing from the icon list After choosing ICON to edit, 15 normal and three audible icons will be displayed. Press the icon you wish to use. The normal icons will be displayed on the map to indicate the map location identified with that icon.
Page 77 Entertainment Systems Home To set home for the first time: • Press MAP. • Press “Nav. Menu”. • Press “Stored Locations.” • Press “Home”. • Press “Add”. Set home by selecting the correct address, POI, Previous destination, or selecting from the map. To view home, press the home icon (house) on the Destination Entry screen.
Page 78 Entertainment Systems Adding a home location • Select the desired menu item you SET HOME wish to set as Home (Address, Memory Point, Point of Interest, Previous Destination). • Enter the required details. • Press OK to set the home position.
Page 79 Entertainment Systems Freeway Entrance/Exit Select “Freeway Entrance/Exit” from the second page of the Destination Entry menu. Follow these steps: 1. Enter freeway name— Enter the freeway name using the keyboard. Press “List” to select a freeway from those displayed. To enter numbers in the freeway name, press “Sym”.
Page 80 Entertainment Systems Special memory points There are five possible memory points that you can set. To set a memory point: • Press MAP. • Press “Nav Menu”. • Press “Stored locations”. • Press “Special Memory Point”. • Select “Add” and input destination. •...
Page 81 Entertainment Systems Adding (storing) a destination or way point • Once a destination is entered, press ADD to store the location. The Store Dest. & Way Point menu is displayed. • Select whether you want to store an Address, Point of Interest or Previous Destination.
Page 82 Entertainment Systems Editing and changing order of way points and destination Press “Chg. Order” to change the order in which the way points are visited. The points are listed chronologically from bottom up, the destination being on the top. Press the MAP button to edit the way point location on the map display.
Page 83 Entertainment Systems Route calculation Once the route criteria is selected, the navigation system automatically calculates the selected destination. The route appears on the display screen and a voice prompt provides instructions. The system may calculate up to four routes for the desired destination. Press “Next”...
Page 84 Entertainment Systems Route interruptions In the course of your destination, you may decide to temporarily leave your planned route for gas, food, etc. If you turn off the ignition, the option to continue the route guidance will be displayed when the ignition is turned on again.
Page 85 Entertainment Systems Listing areas to avoid You can list all areas noted as “avoid”. • Press “Nav Menu”. • Press “Stored locations”. • Press “Avoid area”. • Press LIST to view all previously stored selections. • Select the desired one. The map screen will be displayed, showing the location and address of the selected area.
Page 86 Entertainment Systems To access menu mode, press the MENU hard control. Menu mode allows you to access: • System Set-up • Information — Gives you the Lincoln Customer Assistance Center information. • Brightness/Contrast — Allows you to adjust the brightness and contrast on the screen.
Page 87 Entertainment Systems • Screen off — Allows you to turn off the navigation screen. System setup The system set up menu contains the following user settings: • Audible Feedback — Press to activate audible voice navigation commands. Press again to deactivate.
Page 88 Entertainment Systems • Press AUDIO. • Press DVD to access the DVD screen. You may select from different chapters, rewind or fast forward within the current chapter, stop, play or pause the DVD. You may also select DVD AUX mode (which would allow you to plug in and play games), to enable/disable headphones, or to enable/disable rear seat controls.
Page 89 Motor Company shall not be liable for any damages of any type arising from failure to follow these guidelines. Do not attempt to service, repair or modify the system. See your Ford or Lincoln Mercury dealer. The driver must not attempt to operate any detailed operation of the navigation system while the vehicle is in motion.
Page 90 Ford or Lincoln Dealer. Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford Lincoln Mercury could void user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 91 Entertainment Systems equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help. The database reflects reality as existing before you received the database and it comprises data and information from government and other sources, which may contain errors and omissions.
Page 92 Entertainment Systems Limited GPS reception System performance may be adversely affected if GPS reception is interrupted or interference occurs over a distance of several miles. The following are possible causes for GPS reception being interrupted. If the vehicle is: • in multi-story parking garages •...
Page 93 Entertainment Systems The navigation system utilizes a database stored in a special format on a DVD. It is recommended always to use the latest update of this map DVD. • The navigation system will only work with DVDs specifically intended for your navigation system.
Page 94: Climate Controls
Climate Controls Climate Controls DUAL ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (DEATC) SYSTEM (IF EQUIPPED) DUAL AUTO 1. A/C control 10. Panel control 2. Recirculated air control 11. OFF control 3. Passenger temperature control 12. AUTO control 4. Rear defrost control 13. Driver temperature control 5.
Page 95 Climate Controls AUTOMATIC OPERATION Press AUTO and select the desired temperature. The system will either heat or cool the vehicle to achieve the selected temperature. The system will automatically determine fan speed, airflow location and whether outside or recirculated air is required.
Page 96 Climate Controls TEMPERATURE CONVERSION Press the F/C control to switch between Fahrenheit and Celsius temperature on the display. The temperature in Celsius will be displayed in half-degree increments. The English/Metric control on the trip computer and message center (if equipped) will not change the AUTO temperature display.
Page 97 Climate Controls In automatic operation, the air conditioning operates as necessary to achieve the selected temperature and the A/C indicator will be lit. If desired, the air conditioning can be controlled manually through the use of the A/C control. When the air conditioning is controlled while in automatic operation, the AUTO indicator will remain lit and the system will remain in automatic operation.
Page 98 Climate Controls MANUAL OVERRIDE CONTROLS DUAL AUTO The manual override controls allow you to determine where airflow is directed. To return to full automatic control, press AUTO. The A/C compressor will only function if the outside temperature is above approximately 2°C (35°F). •...
Page 99 Climate Controls OPERATING TIPS • To reduce fogging in humid weather conditions, unless in Defrost or Floor & Defrost, press the A/C control before driving as the air conditioning removes moisture form the air. • To reduce humidity buildup inside the vehicle in warm weather conditions, do not drive with the climate control system in the Off mode.
Page 100 Climate Controls The auxiliary unit can be controlled either by the front seat using the front auxiliary control or by the rear seat passenger(s) using the rear auxiliary control but not both. To control the auxiliary unit using the rear control, the front control must be in the REAR position.
Page 101: Lights
Lights Lights HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Foglamp control The headlamp control also operates the foglamps. The foglamps can be turned on when the headlamp control is in the positions and the high beams are...
Page 102 Lights Daytime running lamps (DRL) (if equipped) Turns the foglamps on at full intensity output. To activate: • the ignition must be in the ON position and • the headlamp control must be in the OFF or Parking lamps position. Always remember to turn on your headlamps at dusk or during inclement weather.
Page 103 Lights PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps. Move the control to the full down position, past detent, to prevent the interior lights from illuminating...
Page 104: Turn Signal Control
Lights 4. On the wall or screen you will observe a light pattern with a distinct horizontal edge towards the right. If this edge is not at the horizontal reference line, the beam will need to be adjusted so the edge is at the same height as the horizontal reference line.
Page 105: Bulb Replacement
Lights INTERIOR LAMPS Front row map lights (if equipped) To turn on the map lights, press the rear edge of the light. Rear dome lamp The dome lamp lights when: • any door is opened (and switch is in middle position). •...
Page 106 Lights Function Number of bulbs Trade number Headlamps 9006 (low-beams) Headlamps (hi-beam) 9005 Front park/turn lamps 3157 AK (amber) Front sidemarker 194 AK (amber) Foglamps Dome/map lamps Turn/tail/brake lamps 3157K Approach lamps Mirror turn signal 906 (amber) lamps Liftgate lamp Backup lamp 3156 License lamp...
Page 107 Lights 3. At the back of the headlamp lens, remove the three headlamp assembly retainers bolts. 4. Pull the headlamp assembly forward slightly to expose the electrical connectors. 5. Rotate the bulb covers counterclockwise and remove. 6. Once the bulb covers are removed, the bulbs can be removed by turning them counterclockwise and then pulling the bulbs straight...
Page 108 Lights Replacing HID headlamp bulbs (if equipped) The low beam headlamps on your vehicle use a “high intensity discharge” source. These lamps operate at a high voltage. The bulb is NOT replaceable. When the bulb is burned out, the lamp assembly must be replaced by your dealer or a qualified technician.
Page 109 Lights 1. Make sure the headlamp switch is in the OFF position. 2. Disconnect the electrical connector from the foglamp bulb. 3. Rotate the foglamp bulb counterclockwise and remove from the foglamp (the rear side of the foglamp is shown). 4.
Page 110 Lights Replacing back-up lamp bulbs The back-up lamp bulbs are located behind the liftgate trim panels. To change the back-up lamp bulbs: 1. Make sure the headlamp switch is in the OFF position. 2. Remove the liftgate trim panel by removing the retaining nuts to expose the bulb socket.
Page 111 Lights 3. Pull the lamp assembly straight out (it will snap out of a plastic retaining grommet). 4. Turn the wire harness counterclockwise to remove it from the lamp. 5. Pull out the bulb and replace it with a new one. 6.
Page 112 Lights High-mount brakelamp To change the high-mount brakelamp bulbs: 1. Remove the two screws holding the lamp assembly in place. 2. Pull the lamp assembly straight out. 3. Remove the wire harness. 4. Depress the four tabs that hold the light assembly on, one at a time, and pull the black bulb carrier away from the lamp.
Page 113 Lights Replacing license plate lamp bulb The license plate bulbs are located in the license plate housing assembly on the liftgate. To change the license plate bulbs: 1. Make sure the headlamp switch is in the OFF position. 2. Remove the license lamp screw from the assembly.
Page 114: Driver Controls
Driver Controls Driver Controls WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. INT1 The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals.
Page 115 Driver Controls Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent. Rinse thoroughly with clean water. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents. Changing the wiper blades It is recommended that wiper blades are renewed before winter.
Page 116 Driver Controls TILT STEERING Push the lever down to unlock the steering column. While the lever is in the down position, tilt the steering column to the desired position. While holding the steering wheel, pull the lever up to its original position to lock the steering column.
Page 117 Driver Controls OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according to your option package. Forward storage bin and conversation mirror (if equipped) The storage compartment may be used to store two pairs of sunglasses or similar objects. Press the release control to open the storage compartment.
Page 118 Driver Controls To vent: • To tilt the moon roof into the vent position (when the glass panel is closed), press and hold the front portion of the control. To close the moon roof from the vent position, press and hold the rear portion of the control until the glass panel stops moving.
Page 119 Driver Controls Power liftgate control (if equipped) Without a moon roof With a moon roof Press and release the top portion of the control to open the power liftgate. Press and release the top portion of the control again to close the power liftgate.
Page 120 Driver Controls AUXILIARY POWER POINT Power points are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power points can cause damage not covered by your warranty. An auxiliary power point is located by the passenger’s ankle near the floor in the front console bin.
Page 121: Power Windows
Driver Controls POWER WINDOWS When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. The power window switches located on the center console are called push-pull switches.
Page 122 Driver Controls • Pull up (to the first detent) and hold the top portion of the switch to close. The following view is the power window switch on the rear door trim panels. • Press and hold the top or bottom of the rear rocker switches to open or close.
Page 123 Driver Controls To operate ONE TOUCH UP: • Pull the switch completely up to the second detent and release quickly. The driver’s window will close fully. Momentarily press the switch to any position to stop the one touch up. If the switch is pressed and held to the normal open or ONE TOUCH DOWN position during a ONE TOUCH UP event, the window will stop.
Page 124: Mirrors
Driver Controls Accessory delay With accessory delay, the radio, windows, and moonroof operate for up to ten minutes after the ignition switch is turned from the ON to the OFF position or until any door is opened. MIRRORS Automatic dimming rear view mirror Your vehicle is equipped with an inside rear view mirror with an auto-dimming function.
Page 125 Driver Controls 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to disable adjust function. Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated.
Page 126 Driver Controls Signal mirrors When the turn signal is activated, the lower portion of the mirror housing will blink. This provides an additional warning to other drivers that your vehicle is about to turn. Power fold mirrors Press the control to retract or extend the outside rear view mirrors.
Page 127 Driver Controls POWER DEPLOYABLE RUNNING BOARDS (IF EQUIPPED) Deployable running boards (DRB) automatically move when the doors are opened to assist entering and exiting the vehicle. Automatic power deploy: • The running boards will extend out when the doors are opened. Automatic power stow: •...
Page 128: Speed Control
Driver Controls SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). Do not shift the gearshift lever into N (Neutral) with the speed control on.
Page 129 Driver Controls Speed control cannot reduce the vehicle speed if it increases above the set speed going downhill. If your vehicle speed is faster than the set speed while driving downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed.
Page 130 Driver Controls • Press CNCL or depress the brake pedal. When the desired vehicle speed is reached, press SET + / SET −. To disengage speed control • Press CNCL, or • depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed.
Page 131 Driver Controls Pressing OFF will erase the previously programmed set speed. To return to a previously set speed • Press RES. For RES to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when the vehicle speed control is engaged and actively controlling vehicle speed.
Page 132 Driver Controls STEERING WHEEL CONTROLS These controls allow you to operate some radio and climate control features. Audio control features Press MEDIA to select: • AM, FM1, FM2, • TAPE, or • CD (if equipped). In AM, FM1, or FM2 mode: •...
Page 133 Driver Controls Climate control features Press TEMP + or - to adjust temperature. Press FAN + or - to adjust fan speed. Navigation steering wheel controls (if equipped) These controls allow you to operate some audio and navigation control features when the vehicle is equipped with the navigation feature. Audio control features Press to select:...
Page 134 Driver Controls In any mode: • Press VOL + or − to adjust volume. Navigation control features Press and hold VOICE until the voice icon appears to use the navigation voice guidance. Press RPT (REPEAT) control to hear previous command repeated from the navigation system.
Page 135 Driver Controls HOMELINK WIRELESS CONTROL SYSTEM The HomeLink Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most current transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.
Page 136 Driver Controls 1. Press and hold the two outside buttons releasing only when the red light begins to flash after 20 seconds. Do not repeat step one to program additional hand-held transmitters to the remaining two HomeLink buttons. This will erase previously programmed hand-held transmitter signals into HomeLink .
Page 137 Driver Controls 7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate step eight. 8. Return to the vehicle and firmly press, hold for two seconds and release the HomeLink button.
Page 138 Driver Controls Operating the HomeLink Wireless Control System To operate, simply press and release the appropriate HomeLink button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.).
Page 139: Message Center
Driver Controls MESSAGE CENTER With the ignition in the ON position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status preceded by a brief indicator chime.
Page 140 Driver Controls Compass display The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions.
Page 141 Driver Controls 7. To exit the zone setting mode, and to “lock in” your change, press and release the RESET control. Perform compass calibration in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut.
Page 142 Driver Controls It is important to press the RESET control after setting the speed control to get accurate highway fuel economy readings. Trip elapsed drive time Select this function from the INFO menu to display a timer. To operate the Trip Elapsed Drive Time perform the following: 1.
Page 143 Driver Controls Setup menu Press this control for the following displays: • System Check • Units (English/Metric) • Autolock • Easy Exit Seat • Reverse Mirrors • Autolamp Delay • Power Liftgate (if equipped) • Power Deployable Running Boards (if equipped) •...
Page 144 Driver Controls 1. To disable/enable the reverse mirror feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the reverse mirrors ON or OFF. Autolamp delay This feature keeps your headlights on for up to three minutes after the ignition is switched off.
Page 145 Driver Controls 1. To disable/enable the power running board feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the power running boards ON (enabled) or OFF (disabled). 3. Select this function from the SETUP control for the current display mode.
Page 146 Driver Controls System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds.
Page 147 Driver Controls This acts as a reminder that these warning conditions still exist within the vehicle. Warning display Status Check park assist Warning displays when R (reverse) gear is selected. PRNDL error no park assist Warning-tire very low (if Warning returns every minute equipped) AdvTrac ON Displays for 4 seconds...
Page 148 Driver Controls CHECK PARK ASSIST. Displayed when the transmission is in R (Reverse). PRNDL ERROR NO PARK ASSIST. Displayed when the transmission is in R (Reverse) and the Backup Aid is disabled. Refer to Backup Aid in this section to enable. ADVTRAC ON.
Page 149 Driver Controls TIRE PRESSURE SENSOR FAULT (if equipped). Displayed when a tire pressure sensor is malfunctioning. If the warning stays on or continues to come on, have the system checked by your dealer. LOW FUEL LEVEL. Displayed as an early reminder of a low fuel condition.
Page 150 Driver Controls SUSPENSION SWITCHED OFF. Displayed when the air suspension switch is in the OFF position. For more information, refer to Air suspension in the Driving chapter. CHECK FUEL CAP. Displayed when the fuel filler cap is not properly installed. Check the fuel filler cap for proper installation. Refer to Fuel filler cap in the Maintenance and specifications chapter.
Page 151 Driver Controls Deactivating overdrive Press the transmission control switch (TCS) located on the gearshift. The O/D OFF indicator light will illuminate on the instrument cluster. The transmission will operate in all gears except overdrive. To return to normal overdrive mode, press the transmission control switch again.
Page 152 Driver Controls Cell phone use The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However, drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency situations.
Page 153 Driver Controls POWER LIFTGATE (IF EQUIPPED) The liftgate can be operated by the following: • overhead console button • key fob button • outside release handle The Overhead console button and Key fob features will only operate the liftgate with the vehicle in P (Park). WARNING: Make sure all persons are clear of the power liftgate area before using the power liftgate control.
Page 154 Driver Controls Note: You will need to wait 2 seconds after opening the liftgate to begin manually closing the power liftgate. Obstacle detection The power liftgate system is equipped with an obstacle detection feature. If the power liftgate is closing, the system is designed to reverse to full open when it encounters a solid obstacle.
Page 155 Driver Controls Make sure the liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. If you must drive with the liftgate open, keep the vents open so outside air comes into the vehicle. LUGGAGE RACK The rear cross-bar can be adjusted to fit the item being carried. The front cross-bar does not move.
Page 156: Locks And Security
Locks and Security Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency.
Page 157: Anti-Theft System
Locks and Security Childproof door locks When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door.
Page 158 Locks and Security • 4–button remote • 5–button remote Press the control a second time within three seconds to unlock all doors and liftgate. Locking the doors/liftgate Press this control to lock all doors and liftgate. To confirm all doors are closed and locked, press the control a second time within three seconds and the horn will chirp.
Page 159 Locks and Security • 5–button remote If any of the doors or liftgate are ajar, the horn will make two quick chirps, reminding you to properly close all doors. Unlocking the liftgate window Press the control to unlatch the liftgate window. •...
Page 160 Locks and Security Opening the power liftgate (if equipped) Press the control twice to fully unlatch and open the liftgate. Make sure all persons are clear of the liftgate area before using power liftgate control. In order to fully lower and latch the liftgate, press the control twice. If the liftgate stops mid travel, it may have detected an obstacle, Check to ensure the liftgate swing zone is free from obstruction and reset the power assist by manually closing the liftgate.
Page 161 Locks and Security • 4–button remote • 5–button remote To deactivate the alarm, press the control again or turn the ignition to ACC or ON. Memory feature The remote entry system can also control the memory feature. Press the control once to unlock the driver’s door. Pressing the control will automatically move the seat, rearview mirrors, and adjustable pedals to the desired memory position (the memory position corresponds to the transmitter being used).
Page 162 Locks and Security • 5–button remote Activating the memory feature To activate this feature: 1. Position the seat, rearview mirror, and adjustable pedals to the positions you desire. 2. Press the SET control on the driver’s door panel. 3. Within 5 five seconds, press one control on the remote transmitter and then press the 1 or 2 control on the driver’s door panel to which you would like to associate with Driver 1 or Driver 2 positions.
Page 163 Locks and Security Replacing the battery The remote transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating range can be caused by the following factors: •...
Page 164 Locks and Security • 4–button remote • 5–button remote Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: •...
Page 165 ON or OFF. Refer to Message center in the Driver controls chapter for additional information. For vehicles not equipped with a message center, the feature may be deactivated by taking your vehicle to an authrorized Ford dealer. 2003 Navigator (nav) Owners Guide (post-2002-fmt)
Page 166 Locks and Security Power door lock disable feature This feature will help protect your vehicle from unauthorized entry. The UNLOCK function on the power door control will not operate with the ignition OFF and twenty seconds after the doors are closed and electronically locked by the remote entry transmitter, key pad, or power door control (if pressed while the door was open).
Page 167 Locks and Security Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes. Your personal code does not replace the permanent code that the dealership gave you.
Page 168 The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. THEFT INDICATOR The theft indicator is the flashing red indicator located on the dash panel.
Page 169 Locks and Security Automatic arming The vehicle is armed immediately after switching the ignition to the 1 (OFF) position. Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. Key information Your vehicle is supplied with two coded keys. Only a coded key will start your vehicle.
Page 170 Locks and Security If an unprogrammed key is used in the ignition it will cause a “no start” condition. Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLock keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure.
Page 171: Seating And Safety Restraints
Seating and Safety Restraints Seating and Safety Restraints SEATING Front row adjustable head restraints Your vehicle’s seats are equipped with four-way adjustable head restraints. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 172 Seating and Safety Restraints Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward side of the control to adjust firmness. Press the rear side of the control to adjust softness.
Page 173 Seating and Safety Restraints Press the control to move the seat forward, backward, up or down. Press the control to recline the seatback forward or rearward. Memory seats/rearview mirrors/adjustable pedals This system allows automatic positioning of the driver seat, outside rearview mirrors, and adjustable pedals to two programmable positions.
Page 174 Seating and Safety Restraints CLIMATE CONTROLLED SEATS (if equipped) The controls for the climate controlled seats are located on the center console. To operate the climate controlled seats the engine must be running. • Push the icon on the button to activate cooled seats.
Page 175 Seating and Safety Restraints • There is a filter located under both front seats. • It can be accessed from the second row seat. Move the front seat all the way forward and up to ease access. To remove climate controlled seat air filter: •...
Page 176 Seating and Safety Restraints To install climate controlled seat air filter: • First, position the filter in it’s housing making sure that the far forward end is all the way up in the housing. Then push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position.
Page 177 Seating and Safety Restraints For assistance, refer to the label located on the side of the seat cushion. Adjusting the 2nd row outboard seat for E-Z Entry The 2nd row outboard seats allow for easier entry and exit to and from the 3rd row seat.
Page 178 Seating and Safety Restraints 3. To return the seat to a seating position, push down on the seat until the seat is latched to the floor. 4. Lift the seatback to the upright position. Always latch the vehicle seat to the floor, whether the seat is occupied or empty.
Page 179 Seating and Safety Restraints 3. Locate the latch strap at the front of the seat and pull to release the seat into a kneel down load floor position. A moderate force may be required to move the seat forward and down. Once the second row seats are in the down position, the front seats may be readjusted.
Page 180 Seating and Safety Restraints The rear latch hooks must be properly engaged with the floor striker. Position the rear legs of the seat over the floor strikers and engage. Folding the 20% seat system (if equipped) 1. Locate the release strap located between the front cushion and the seat back, and pull the strap to release the folding seat latch.
Page 181 Seating and Safety Restraints 3. To return the seat to the upright position, lift the seatback until the latch is fully engaged. Adjusting the second row 20% seat (if equipped) Lift the handle to move the seat forward or backward. Note: This seat can be moved forward to keep a child in a child restraint close to the front seat occupants.
Page 182 Seating and Safety Restraints Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Third row seats Ensure that no objects such as books, purses or briefcases are on the floor in front of the third row seats or on the seat cushion before lowering them.
Page 183 Seating and Safety Restraints Push the bottom portion of the control button to lower the desired seatback. Push the top of the control button to return the seatback to its original position. The power folding seats are designed to stall within 1–10 seconds of encountering an obstruction when opening or closing.
Page 184: Safety Restraints
Seating and Safety Restraints The head restraints can be moved up and down. Push control to lower head restraint. SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of air bag-related injuries.
Page 185 Seating and Safety Restraints • Front safety belts with pretensioners, energy management retractors, and safety belt usage sensors. • Driver’s seat position sensor. • Front crash severity sensor. • Restraints Control Module (RCM). • Restraint system warning light and back-up tone. •...
Page 186 Seating and Safety Restraints Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System to tailor the deployment level of the driver dual-stage air bag based on seat position. The system is designed to help protect smaller drivers sitting close to the driver air bag by providing a lower air bag output level.
Page 187 Seating and Safety Restraints • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and warning light are repaired. If any of these things happen, even intermittently, have the Personal Safety System serviced at your dealership or by a qualified technician immediately.
Page 188 Seating and Safety Restraints Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them.
Page 189 Seating and Safety Restraints movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.
Page 190 Seating and Safety Restraints How to disengage the automatic locking mode Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. After any vehicle collision, the combination lap and shoulder belt system at all passenger seating positions must be checked by a qualified technician to verify that the “automatic locking retractor”...
Page 191 Seating and Safety Restraints Front and second row safety belt height adjustment Your vehicle has safety belt height adjustments for the driver, right front passenger and second row outboard passengers. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.
Page 192 Seating and Safety Restraints Conditions of operation If... Then... The driver safety belt is not The safety belt warning light buckled before the ignition illuminates 1-2 minutes and the switch is turned to the ON warning chime sounds 4-8 seconds. position...
Page 193 Seating and Safety Restraints If... Then... The driver’s safety belt is The BeltMinder feature will not buckled before the ignition activate. switch is turned to the ON position... The purpose of the BeltMinder is to remind occasional wearers to wear safety belts all of the time.
Page 194 Seating and Safety Restraints Reasons given... Consider... “Belts wrinkle my clothes” Possibly, but a serious crash can do much more than wrinkle your clothes, particularly if you are unbelted. “The people I’m with don’t Set the example, teen deaths occur 4 wear belts”...
Page 195 Seating and Safety Restraints • The ignition switch is in the OFF position • All vehicle doors are closed • The driver’s safety belt is unbuckled • The parklamps/headlamps are in OFF position (If vehicle is equipped with Autolamps, this will not affect the procedure.) To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle.
Page 196: Air Bags
(if equipped), child safety seat LATCH and tether anchors, and attaching hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies used in vehicles involved in a collision be replaced.
Page 197 Seating and Safety Restraints Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly; there is a risk of injury from a deploying air bag.
Page 198 Seating and Safety Restraints Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. The front passenger air bag is not designed to offer protection to an occupant in the center front seating position.
Page 199 Seating and Safety Restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation.
Page 200 Seating and Safety Restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Page 201 Do not attempt to service, repair, or modify the Safety Canopy system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy . See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always...
Page 202 Seating and Safety Restraints How does the Safety Canopy system work? The design and development of the Safety Canopy system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Air Bag Technical Working Group.
Page 203 Seating and Safety Restraints The Safety Canopy is mounted to roof side-rail sheet metal, behind the headliner, above the first and second row seats. In certain lateral collisions or rollover events, the Safety Canopy system will be activated, regardless of which seats are occupied. In certain rollover events, the Safety Canopy on both sides of the vehicle will be inflated, regardless of which seats are occupied.
Page 204: Child Restraints
Seating and Safety Restraints Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Air bag readiness section in the Instrument Cluster chapter. Routine maintenance of the air bag is not required.
Page 205 To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster. Booster seats position a child so that safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably.
Page 206 Seating and Safety Restraints When children should use booster seats Children need to use booster seats from the time they outgrow the toddler seat until they are big enough for the vehicle seat and lap/shoulder belt to fit properly. Generally this is when they weigh about 80 lbs (about 8 to 12 years old).
Page 207 Seating and Safety Restraints • Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice. Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lbs.
Page 208 Seating and Safety Restraints SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Page 209 Ford recommends the use of a child safety seat having a top tether strap and LATCH attachments. Install the child safety seat in a seating position which is capable of providing tether and LATCH anchors.
Page 210 Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Page 211 Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 212 Seating and Safety Restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap.
Page 213 Seating and Safety Restraints • outboard seating positions • center seating position (if equipped) 3. Route the child safety seat tether strap under the head restraint (outboard seats) and over the back of the seat. 4. Grasp the tether strap and position it to the seat frame.
Page 214 Seating and Safety Restraints 5. Rotate the tether strap, and clip the tether strap to the anchor on the seat frame. 6. Rotate the tether strap clip. 7. Tighten the child safety seat tether strap according to the manufacturer’s instructions. Third row seating position 1.
Page 215 Seating and Safety Restraints • You may need to pull back the top of the hinged panel along the bottom of the seat back to access the tether anchor. 4. Clip the tether strap through the anchor loop as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly...
Page 216 Seating and Safety Restraints Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. This type of child seat eliminates the need to use seat belts to attach the child seat.
Page 217 Seating and Safety Restraints The lower anchors for child seat installation are located at the rear section of the second row seat between the cushion and seat back. The LATCH anchors are below the locator symbols on the seat back. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments.
Page 218: Driving
Driving Driving STARTING Positions of the ignition 1. OFF/LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational.
Page 219 Driving If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine.
Page 220 Driving 5. Turn the key to 3 (ON) without turning the key to 4 (START). Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate.
Page 221: Brakes
Driving Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. If the engine still fails to start, press the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel.
Page 222 Driving “continuous squeal” sound is present while braking, the brake linings may be worn-out and should be inspected by a qualified service technician. If you are driving down a long or steep hill, shift to a lower gear. Do not apply your brakes continuously, as they may overheat and become less effective.
Page 223 Driving • We recommend that you familiarize yourself with this braking technique. However, avoid taking any unnecessary risks. ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced.
Page 224 Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The parking brake is not recommended to stop a moving vehicle.
Page 225: Air Suspension
Driving • Do not operate the vehicle with the power steering pump fluid level below the MIN mark on the reservoir. If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, check for: •...
Page 226 Driving When the vehicle is in motion, the air suspension will adjust the vehicle ride height to normal operating position to maximize your ride comfort. If your vehicle is equipped with four-wheel drive and you shift into 4WD LOW, the air suspension will not move to it’s lowest position; instead, the ride height is raised above the normal ride height position (at speeds below 40 km/h [25 mph]) to improve ground clearance.
Page 227 Driving To remove the second panel, press the tab down to unlock the access panel. Press the bottom portion of the switch to turn off the air suspension. 2003 Navigator (nav) Owners Guide (post-2002-fmt) USA English (fus)
Page 228 Driving LIMITED-SLIP AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the limited slip axle functions like a standard rear axle. Extended use of other than the manufacturer’s specified size tires on a limited slip rear axle could result in a permanent reduction in effectiveness.
Page 229 Driving ADVANCETRAC STABILITY ENHANCEMENT SYSTEM (IF EQUIPPED) The AdvanceTrac system provides a stability enhancement feature as well as a traction enhancement feature. It helps your vehicle maintain traction, when driving on slippery and/or hilly road surfaces, by detecting and controlling wheel spin. Excessive wheel spin is controlled by momentarily reducing engine power and rapidly applying the anti-lock brakes.
Page 230 Driving • Driving on slick surfaces • Cornering while towing a heavily loaded trailer (refer to Trailer Towing in this chapter) The AdvanceTrac system automatically turns on when the engine is started. However, the system does not function when the vehicle is traveling in R (Reverse) or, if equipped with four-wheel drive, in 4L (4X4 LOW).
Page 231 Driving Some drivers may notice a slight movement of the brake pedal when the AdvanceTrac performs a system self-check. During AdvanceTrac operation you may experience the following: • A rumble or grinding noise • A slight deceleration of the vehicle •...
Page 232: Transmission Operation
Driving AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly.
Page 233 Driving 4. Press and hold the white button located along side the shifter housing assembly (as shown in the illustration). Press the gearshift lever release on the shifter knob and move the gearshift lever back to N (Neutral) (two places rearward from P [Park]).
Page 234 Driving Driving with a 4–speed automatic transmission Your vehicle’s automatic transmission is equipped with a special shift strategy that insures maximum heater performance during cold weather operation. When ambient temperature is –5° C (23° F) or below and the engine coolant temperature is below 38°...
Page 235 Driving R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll.
Page 236 Driving (Overdrive) can be deactivated by pressing the transmission control switch (TCS) on the end of the gearshift lever. The transmission control indicator light (TCIL) will illuminate in the instrument cluster. Drive – Not shown on the display. Activate by pressing the transmission control switch (TCS) on the end of the gearshift lever with the gearshift in the position.
Page 237 Driving 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive).
Page 238 Driving If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow, it may be rocked out by shifting from forward and reverse gears, stopping between shifts in a steady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur.
Page 239 Driving The system detects obstacles up to a maximum range of six meters (20 ft.) behind the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases.
Page 240 The Control Trac system indicator lights illuminate only under the following conditions. If these lights illuminate when driving in 2H or A4WD, contact your Ford dealer as soon as possible. • 4X4 HIGH - momentarily illuminates when the vehicle is HIGH started.
Page 241 Driving Positions of the Control Trac system The Control Trac system functions in four modes: • 2H (2WD HIGH) delivers power to the rear wheels only. This is appropriate for normal on-road driving on dry pavement. • A4WD (4X4 AUTO) provides electronic control four-wheel drive with power delivered to all four wheels, as required, for...
Page 242 Driving Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns or abrupt maneuvers in these vehicles.
Page 243 Driving Shifting from 2H, A4WD or 4H to 4L 1. Bring the vehicle to a stop and keep the brake pedal depressed. 2. Place the gearshift in N (Neutral). 3. Move the control to the 4L position. Note: Some noise may be heard as the system shifts or engages. Shifting from 4L to 4H, A4WD or 2H 1.
Page 244 Driving How your vehicle differs from other vehicles Truck and utility vehicles can differ from some other vehicles. Your vehicle may be higher to allow it to travel over rough terrain without getting hung up or damaging underbody components. The differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car.
Page 245 Driving Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions.
Page 246 Driving • In the event of an emergency stop, avoid skidding the tires and do not attempt any sharp steering wheel movements. Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity.
Page 247 Driving Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Avoid reducing the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels.
Page 248 Ford Motor Company joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly.”...
Page 249 Driving Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control.
Page 250 (a label may also be found on the fuel cap filler door). Failure to follow tire pressure recommendations can adversely affect the way your vehicle handles. Do not exceed the Ford Motor Company recommended pressure even if it is less than the maximum pressure allowed for the tire.
Page 251 Ford Motor Company recommends that caution be used with any vehicle equipped with a high load or device (such as ladder racks or pickup box cover).
Page 252: Vehicle Loading
Driving If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars). Once through the water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes.
Page 253 Driving • Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and cargo) is permitted to tow. It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle. •...
Page 254: Trailer Towing
Driving Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle. Your vehicle has the capability to haul more cargo and people than most passenger cars.
Page 255 A kit containing a wiring harness/adapter and installation instructions to attach an electric brake controller may be obtained from any Ford or Lincoln/Mercury dealer (part number 2L1Z-14A348-AB). Before towing a trailer, make sure the trailer brakes (if equipped) and lamps are properly connected and functional.
Page 256 Driving INTEGRATED HITCH RATING The standard integrated hitch has two ratings depending on mode of operation: • Weight carrying - requires a draw bar and hitch ball. The draw bar supports all the vertical tongue load of the trailer. • Weight distributing - requires an aftermarket weight distributing system which includes draw bar, hitch ball, spring bars and snap-up brackets.
Page 257 Driving 2. To reinstall the cover, insert the three plastic tabs into their slots (as shown in the illustration) and push the cover up into the bumper trim. 3. Hold the cover against the bumper trim and reinstall the two screws. Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle.
Page 258 Driving Note: Adjusting an equalizing hitch so the rear bumper of the vehicle is higher than it was unloaded will defeat the function of the load equalizing hitch and may cause unpredictable handling. Safety chains Always connect the trailer’s safety chains to the frame or hook retainers of the vehicle hitch.
Page 259 Driving • Anticipate stops and brake gradually. • Do not exceed the GCWR rating or transmission damage may occur. Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your scheduled maintenance guide for more information.
Page 260 If a distance of 80 km (50 miles) or a speed of 56 km (35 mph) must be exceeded, the drive shaft will have to be removed before the vehicle is towed. Ford recommends the driveshaft be removed/installed only by a qualified technician. See your local dealer for driveshaft removal/installation. Improper removal/installation of the driveshaft can cause transmission fluid loss, damage to the driveshaft and internal transmission components.
Page 261: Roadside Emergencies
Roadside Emergencies Roadside Emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: •...
Page 262: Hazard Flasher Switch
1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673;...
Page 263 Roadside Emergencies The fuel pump shut-off switch is located in the left rear quarter trim panel, near the liftgate. The switch is located behind two access panels; the second panel has a tab that needs to be pushed down to remove the access panel door.
Page 264: Fuses And Relays
Roadside Emergencies Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button.
Page 265 Roadside Emergencies Standard fuse amperage rating and color COLOR Cartridge Fuse Mini Standard Maxi Fuse link maxi rating fuses fuses fuses cartridge fuses Grey Grey — — — Violet Violet — — — Pink Pink — — — — — —...
Page 266 Roadside Emergencies To remove the fuse box cover, place a finger behind the PULL tab and your thumb above the PULL tab as shown in the illustration, then pull the cover off. To reinstall the fuse box cover, place the top part of the cover on the fuse panel, then push the bottom part of the cover until you hear it click shut.
Page 267 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 10A* Run/Accessory - Instrument cluster, Front wiper motor, Rear wiper motor, Tire Pressure Monitor System (TPMS) module 20A* Brake On/Off (stoplamp) switch, Turn signal/Hazard flasher, AdvanceTrac stoplamps relay, Stoplamps, Center High-Mounted Stoplamp (CHMSL), Turn signal lamps...
Page 268 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 15A* Headlamp switch (parklamps and switch backlighting feed), Parklamps, License lamps, Foglamp relay coil, Trailer tow electric brake controller (illumination), BSM (autolamp parklamps), Floor console gear selector lighting, Switch backlighting module, Foglamp indicator 7.5A*...
Page 269 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 10A* Rear window defroster relay coil, A/C refrigerant containment switch, A/C compressor thermistor, DEATC control head, DEATC solenoids, DEATC blower controller, Trailer tow battery charge relay coil 10A* Daytime Running Lamps (DRL) ignition relay coil, Digital Transmission Range Sensor...
Page 270 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 15A* Instrument cluster (B+), Interior (courtesy) lamps, TPMS module, Park brake release relays, Park brake release motor, Puddle lamps (outside mirrors) 10A* Moonroof switch illumination, Flip window switch, Flip window relays, Flip window motors, Electronic Hidden Antenna Module (EHAM) antenna...
Page 271 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 30A* BSM (door locks, liftgate glass release relay), Liftgate glass release motor, Left front window motor, Door/Liftgate lock motors 25A* Radio (B+), Subwoofer, Navigation radio audio amplifier 15A* Catalyst Monitor Sensors (CMS), Transmission solenoids 20A*...
Page 272 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 20A* DRL relays, DRL foglamps, DRL headlamp relay coil, Headlamp switch (headlamps), Multifunction switch (flash-to-pass), BSM (autolamp headlamps relay), High beam relay coil, Fuse 25 (LH low beam), Fuse 23 (RH low beam) 20A* Cigar lighter, OBD II diagnostic connector...
Page 273 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 30A** Power running boards 50A** Air suspension compressor relay, Air suspension compressor 30A** ABS/AdvanceTrac module (valves) 30A** Front wiper motor, Washer pump (windshield wash) 40A** Rear window defroster relay, Rear window defroster grid, Heated mirrors (Fuse 8) 30A**...
Page 274 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description Rear window Fuse 8 (heated mirrors), Rear defrost relay window defroster, Heated outside mirrors, Rear window defroster indicator (climate control head) Trailer tow Trailer tow 7–wire connector battery charge (battery charge) relay Front blower...
Page 275: Changing Tires
Roadside Emergencies CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. The use of tire sealants is not recommended and may compromise the integrity of your tires.
Page 276 Roadside Emergencies Removing the spare tire 1. Fold the rear seat down. Refer to Rear seats in the Seating and safety restraints chapter. 2. Remove the jack handle and winch extension from the tray and assemble them. 3. Open the spare tire winch access plug in the bottom of the compartment located behind the 3rd row seat, very close to the jack and...
Page 277 Roadside Emergencies 1. Park on a level surface, activate hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park), turn engine OFF and block the diagonally opposite wheel. (If changing the tire on a grade, block the diagonally opposite wheel on the downward side of the grade.) 3.
Page 278 Roadside Emergencies 4. Use the tip of the jack handle to remove any wheel trim. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 5. Position the jack according to the jack locator arrows found on the frame and turn the jack handle and extension tool assembly clockwise.
Page 279 Roadside Emergencies • Rear Turn off the running boards before jacking or placing any object under the vehicle. Never place your hand between the extended running board and the vehicle. A moving running board may cause injury. • Never use the front or rear differential as a jacking point.
Page 280 Roadside Emergencies 9. Remove the jack and fully tighten the lug nuts in the order shown and reinstall the wheel cover. 10. Unblock the wheels. 11. Put flat tire, jack, lug wrench and tools away. Make sure the jack is fastened securely so it does not rattle when you drive.
Page 281: Jump Starting
Roadside Emergencies JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted.
Page 282 Roadside Emergencies Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 283 Roadside Emergencies 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to the jump starting stud located in the rear of the engine compartment, near the battery.
Page 284 Roadside Emergencies Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts.
Page 285 Roadside Emergencies 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 2003 Navigator (nav) Owners Guide (post-2002-fmt) USA English (fus)
Page 286 Roadside Emergencies 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 287: Wrecker Towing
It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. Also, wrecker towing the vehicle by the front frame-mounted tow hooks is not recommended or advised.
Page 288 • Do not exceed a distance of 80 km (50 miles). • Do not exceed 56 km/h (35 mph) vehicle speed. Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.
Page 289: Customer Assistance
Ford Customer Relationship Center. Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 290 If you still have a complaint involving a warranty dispute, you may wish to contact the Dispute Settlement Board (U.S.). In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states.
Page 291 5,000 participating Ford or Lincoln Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www.ford-esp.com.
Page 292 Customer Assistance The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Page 293 • The name of the dealer(s) who sold or serviced the vehicle. • A brief description of your unresolved concern. • A brief summary of the action taken by the dealer(s) and Ford Motor Company. • The names (if known) of all the people you contacted at the dealership(s).
Page 294 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 295 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY...
Page 296 Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3. IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer...
Page 297: Reporting Safety Defects (U.s. Only)
However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (or 366–0123 in the Washington D.C.
Page 298: Cleaning
Cleaning Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid.
Page 299 Cleaning • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained body-side cladding, roof racks, bumper step surfaces, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.
Page 300 Cleaning • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage.
Page 301 Cleaning • Do not use fuel, kerosene, or paint thinner to clean any parts. • Wiper blades can be cleaned with isopropyl (rubbing) alcohol or windshield washer solution. Be sure to replace wiper blades when they appear worn or do not function properly. INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then dry with a dry cloth.
Page 302 FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
Page 303 Motorcraft Wheel and Tire Cleaner (ZC-37–A) Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Car Care Kit (ZC-26) Ford Premium Car Wash Concentrate (F2SZ-19523–WC) Motorcraft Carlite Glass Cleaner (Canada only) (CXC-100) Motorcraft Spot and Stain Remover (ZC-14) Motorcraft Detail Wash (ZC-3–A)
Page 304: Maintenance And Specifications
Maintenance and Specifications Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 305 Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch located under the front of the hood, just above the passenger side headlamp.
Page 306: Engine Compartment
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L 4V V8 engine 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Power steering fluid reservoir 5. Engine oil dipstick 6. Brake fluid reservoir 7. Engine coolant reservoir 8.
Page 307: Engine Oil
In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Page 308 Maintenance and Specifications 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable.
Page 309 Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). To protect your engine’s warranty use Motorcraft SAE 5W-20 or an equivalent 5W-20 oil meeting Ford specification WSS-M2C153–H. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine.
Page 310: Battery
Maintenance and Specifications that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application.
Page 311 Maintenance and Specifications Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
Page 312 Maintenance and Specifications 7. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 16 km (10 miles) or more to relearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
Page 313 Maintenance and Specifications • Enables calibrated gauges to work properly. When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “cold fill level” or within the “cold fill range”...
Page 314 If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • Add Motorcraft Premium Gold Engine Coolant (yellow-colored), VC-7–A (VC-7–B in Oregon), meeting Ford Specification WSS-M97B51–A1. Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan.
Page 315 Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available.
Page 316 Maintenance and Specifications Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Severe climates If you drive in extremely cold climates (less than –36°...
Page 317 Maintenance and Specifications How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The and the symbol will illuminate. • The “Service Engine Soon” indicator light will illuminate. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation.
Page 318: Fuel Information
Maintenance and Specifications 5. Restart the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to a service facility as soon as possible. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank.
Page 319 Maintenance and Specifications • Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury. •...
Page 320 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Page 321 Ask your fuel supplier about gasolines that meet the World-wide Fuel Charter. Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components.
Page 322 Maintenance and Specifications If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. •...
Page 323 Maintenance and Specifications For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled.
Page 324 Maintenance and Specifications Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel.
Page 325 Maintenance and Specifications • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy. • Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first 12–16 km (8–10 miles) of driving.
Page 326 If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 327 Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary, use only Ford Premium Power Steering Fluid or MERCON ATF. 1. Start the engine and let it run until it reaches normal operating...
Page 328 Maintenance and Specifications 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and...
Page 329 Maintenance and Specifications 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operating temperature. 2. Park the vehicle on a level surface and engage the parking brake. 3. With the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges.
Page 330: Air Filter(S)
Maintenance and Specifications High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission COLD DO NOT ADD fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used.
Page 331 Maintenance and Specifications Changing the air filter element 1. Loosen the clamp that secures the air inlet tube to the engine air filter cover and disconnect the tube from the cover. 2. Loosen the clamp that secures the air filter cover to the air filter housing and carefully separate the cover from housing.
Page 332 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 333 Maintenance and Specifications The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 334 Maintenance and Specifications Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly resulting in loss of vehicle control, vehicle rollover and/or personal injury. Tire rotation Because your vehicle’s tires perform different jobs, they often wear differently. To make sure your tires wear evenly and last longer, rotate them as indicated in the scheduled maintenance guide.
Page 335: Low Tire Warning System
Make sure that all replacement tires are of the same size, type, speed rating, load-carrying capacity and tread design (e.g., “All Terrain”, “Touring”, etc.), as originally offered by Ford. Do not replace your tires with “high performance” tires or larger size tires.
Page 336 Follow these guidelines when using snow tires and chains: • Use only cable type chains or chains offered by Ford as an accessory or equivalent. Other conventional link type chains may contact and cause damage to the vehicle’s wheel house and/or body.
Page 337: Part Numbers
Maintenance and Specifications • Do not install chains on the front wheels. Chains on the front wheels may interfere with suspension components. • Chains are not recommended for use on the optional P275/65R18 tire. • Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines.
Page 338: Refill Capacities
Maintenance and Specifications REFILL CAPACITIES Fluid Ford Part Application Capacity Name Brake fluid Motorcraft High Fill to line on Performance reservoir DOT 3 Motor Vehicle Brake Fluid Engine oil Motorcraft SAE 6.6L (7.0 quarts) (includes filter 5W-20 Premium change) Synthetic Blend...
Page 339 Maintenance and Specifications Fluid Ford Part Application Capacity Name Rear axle Motorcraft SAE Conventional 2.13L (4.5 pints) lubricant 75W-90 Fuel differential Efficient High (9.75 inch Performance axle) Synthetic Rear Axle Lubricant Motorcraft SAE Limited-slip 2.01L (4.25 pints) 75W-140 High differential Performance (9.75 inch...
Page 340: Lubricant Specifications
12mm (3/8 inch to 1/2 inch) below the bottom of the filler hole. Add 118 ml (4 oz.) of Additive Friction Modifier XL-3 or equivalent meeting Ford specification EST-M2C118–A for complete refill of Limited Slip axles. For complete refills, fill using the Additive Friction Modifier first.
Page 341 Maintenance and Specifications Ford part Ford part Ford Item name number specification Engine coolant Motorcraft VC-7–A WSS-M97B51-A1 Premium Gold Engine Coolant (yellow-colored) Engine oil Motorcraft SAE XO-5W-20-QSP WSS-M2C153-H 5W-20 Premium with API Synthetic Blend Certification Motor Oil Mark 4x4 front wheel...
Page 342 Use of any fluid other than the recommended fluid may cause transmission damage. Add 118 ml (4 oz.) of Additive Friction Modifier XL-3 or equivalent meeting Ford specification EST-M2C118-A for complete refill of Ford Limited Slip rear axles. 2003 Navigator (nav)
Page 343 Maintenance and Specifications ENGINE DATA Engine 5.4L 4V V8 engine Cubic inches Required fuel 91 octane Firing order 1-3-7-2-6-5-4-8 Spark plug gap 1.3-1.4 mm (0.052-0.056 inch) Ignition system Coil on plug Compression ratio 9.5:1 VEHICLE DIMENSIONS Vehicle dimensions 4x2 and 4x4 mm (in) (1) Overall length 5232.0 (206) (2) Vehicle width...
Page 344 Maintenance and Specifications 2003 Navigator (nav) Owners Guide (post-2002-fmt) USA English (fus)
Page 345 Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side.
Page 346: Accessories
Not all accessories are available for all models. Following is a list of several Ford Genuine Accessory products. Not all accessories are available for all models. To find out what accessories are available for your vehicle, please contact your dealer or visit our online store at: www.lincolnaccessories.com.
Page 347 Accessories Travel equipment First aid kit Hard shell cargo box Highway safety kit Hitch mount bike rack Load warrior carrier basket Load warrior carrier extension Load warrior light bracket Navigation system Pet guard/divider Raised cross bars Raised cross bar adaptors Trailer hitch bars and balls Trailer hitch mounted bike carrier Trailer hitch receiver cover...
Page 348 • Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment. • Do not install equipment which modifies the vehicles suspension or steering.
Page 349: Index
Index Index acid, treating emergencies ..310 charging system warning light ..........12 ABS (see Brakes) .....222 jumping a disabled battery ..281 Accessory delay ......124 maintenance-free ....310 Air bag supplemental restraint replacement, specifications ...337 system ......196–197, 201 servicing ........310 and child safety seats ....198 BeltMinder .........192 description ......197, 201 disposal ........204...
Page 350 ....247, 251 Cruise control Dual automatic temperature (see Speed control) ....128 control (DATC) ......94 Customer Assistance ....261 Ford accessories for your vehicle ........302 Ford Extended Service Electronic message center ..139 Plan ..........291 Emergencies, roadside Getting assistance outside the jump-starting ......281...
Page 351 Index idle speed control ....310 choosing the right fuel ...320 lubrication comparisons with EPA fuel specifications ....340, 343 economy estimates ....325 refill capacities ......338 detergent in fuel .....321 service points ......306 filling your vehicle with starting after a collision ..262 fuel ......318, 320, 322 filter, specifications ..322, 337 Engine block heater ....221...
Page 352 Index definition .........252 positioning .......275 driving with a heavy load ..252 storage ........275 location ........252 Jump-starting your vehicle ..281 Hazard flashers ......262 Keyless entry system Headlamps .........101 autolock ........165 aiming ........103 locking and unlocking doors ..167 autolamp system .....101 programming entry code ..166 bulb specifications ....105 Keys ........168–170 daytime running lights ...102...
Page 353 Index oil pressure .......12 quick start .........46 overdrive off ......13 radio functions ......50 safety belt .........12 service engine soon ....10 speed control ......131 turn signal indicator ....13 Octane rating ......321 Limited-slip axle .......228 Odometer ........16 Load limits .........252 Oil (see Engine oil) ....307 GAWR ........252 Overdrive ........150 GVWR ........252...
Page 354 Index Remote entry system ..157, 160 Spare tire (see Changing the Tire) ...........275 illuminated entry ....165 locking/unlocking Spark plugs, specifications .....337, 343 doors ......156–158, 166 opening the trunk ...159–160 Special notice panic alarm ......160 utility-type vehicles ....7 replacement/additional Specification chart, transmitters ......163 lubricants ......340, 343 replacing the batteries ...163...
Page 355 Index brake-shift interlock (BSI) ..232 Warning lights (see Lights) ..10 fluid, checking and adding Washer fluid ......307 (automatic) ......328 fluid, refill capacities ....338 Water, Driving through .....251 lubricant specifications ..340, 343 Windows Trip odometer ......17 power ........121 Trunk .........159–160 rear wiper/washer ....114 Turn signal ......13, 104 Windshield washer fluid and wipers...

Ford Navigator 2003 Owner's Manual

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Locks and Security

Seating and Safety Restraints

Driving

Roadside Emergencies

Customer Assistance

Cleaning

Maintenance and Specifications

Accessories

Index

Quick Links

Table of Contents

Related Manuals for Ford Navigator 2003

Summary of Contents for Ford Navigator 2003

Table of Contents