Assembling The Rp301R; Stand Assembly - Roland RP301R Owner's Manual

& &

Assembling the RP301R

* To ensure that you assemble this unit correctly, please read this manual carefully before you begin assembly. Keep this manual nearby for reference when needed.
* Keep this unit horizontal when lifting it during assembly or transport.
* Be careful not to pinch your hands or drop this unit on your foot during assembly or transport.
* You must obtain the assistance of at least one additional person when assembling or transporting this unit.
* Keep small parts such as screws out of the reach of small children to ensure that these items are not swallowed accidentally.
* The screwdriver needed for assembly is not included. You will need to provide a Phillips screwdriver of the appropriate size for the screws.
* You should initially tighten each screw loosely before tightening them to their fi nal position. Start by tightening the screws until they are approximately half hidden. Do not use a
power screwdriver when tightening the screws to their fi nal position. Doing so may strip the threads.
* Tighten the screws fi rmly, and place the unit at a location that is level and sure to remain stable. Never place the unit on a shag carpet. If you do so, the pedal may be unstable,
causing damage.
* Do not place the body of the piano directly on the fl oor. Doing so will damage the jacks and holders on the bottom of the piano, and also damage the bottom panel case.
Copyright © 2011 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
Checking the parts
1
2
5
3
6

1. Stand assembly

* At fi rst, assemble the entire stand in a temporary fashion, without
really tightening the screws. Then, after checking the overall
alignment of the boards (and gently shifting certain parts where
necessary), go around and tightly fasten each of the screws.
* If necessary, spread out a blanket or similar material to prevent the
stand or fl oor from being scratched during assembly.
* Be careful not to pinch the pedal cord during assembly.
1.
As shown in the illustration, place the left and right side
boards on the pedal board so that the metal brackets are on
the inside, and fasten them provisionally using screws
(5 x 40 mm).
2.
Hand-tighten screws
screwdriver to tighten them securely.
* When attaching the pedal board, do not allow any gap to remain
between the side board and pedal board when the pieces are
assembled.
Side
board
Screw C (2 pcs.)
Leave the pedal cord extended
3.
With the help of another person, raise the left and right side
boards to an upright position.
* Take care that the pedal boards are not twisted.
38
1
Music rest
2
Piano main unit
3
Side board (left)
4
4
Side board (right)
5
Rear board
6
Pedal board
(four locations), and then use a
C
Don't allow a
gap!
Screw C (2 pcs.)
A
B
C
D
E
F
4.
Place the rear board as shown below and adjust the screw
holes of the rear board and the pedal board.
* If you have diffi culty inserting the rear board, loosen screws
is easier to position the rear board in the stand.
C
5.
Attach the rear board to the metal parts on the side boards
from the front using screws
For clamping the rear board, press each upper portion of both side
boards.
6.
Then, fasten it to the pedal board from the back using
screws (4 × 20 mm).
B
Screw A
7.
Go around and tighten all the screws, while at the same
time correcting the orientation of any piece that needs it,
until everything fi ts together properly.
* When attaching the rear board, before tightening the screws, adjust
things as necessary at all the points where there are screws so as to
assure that the rear board is aligned in parallel with the pedal board.
Screw (4 × 14 mm): 2 pcs.
Screw (4 × 20 mm): 4 pcs.
Screw (5 × 40 mm): 4 pcs.
Screw (5 × 20 mm): 2 pcs.
Screw (4 × 16 mm): 2 pcs.
Headphone hook: 1 pcs.
The RP301R-RW has a simulated rose wood
fi nish. The wood grain should face forwards.
(4 x 14 mm).
A
B
Screw
so it
C