Table of Contents
Advertisement
Quick Links
MOTORCYCLE
MOTORCYCLE
Ride-On
Ride-On
Product features may vary from the picture above.
Please read this manual and save it with your original sales receipt.
Tools needed for assembly: Phillips Screwdriver, Hammer and Safety Scissors (not included).
Use only with a Power Wheels
®
12 Volt Rechargeable Battery
and a Power Wheels
®
12 Volt Charger (all included).
Sound and Light Box requires three "AA" (LR6) alkaline batteries (not included).
Harley-Davidson is a registered trademark
and the motorcycle sound is a trademark of
H-D Michigan, Inc. used under license.
Fisher-Price, Power Wheels by Fisher-Price and
Power Lock are U.S. trademarks of Mattel, Inc.
Owner's Manual
with Assembly Instructions
For Model 74287
Advertisement
Table of Contents
Related Manuals for Fisher-Price RIDE-ON 74287
Summary of Contents for Fisher-Price RIDE-ON 74287
- Page 1 ® 12 Volt Charger (all included). Sound and Light Box requires three “AA” (LR6) alkaline batteries (not included). Harley-Davidson is a registered trademark and the motorcycle sound is a trademark of H-D Michigan, Inc. used under license. Fisher-Price, Power Wheels by Fisher-Price and Power Lock are U.S.
-
Page 2: Table Of Contents
Important Information ..............2 Warnings and Cautions . -
Page 3: Warnings And Cautions
ELECTRICAL HAZARD • Battery can fall out and injure a child if vehicle tips over. Always use battery clamp. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury. -
Page 4: Parts
• If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. - Page 5 Parts Exhaust Pipe Set Left - Inner Right - Inner Right - Outer Left - Outer Rear Headlight Front Headlight Seat Gas Tank Saddlebag - 2 Fork Cover Front Fork Light and Sound Box Flashing Light Lens...
- Page 6 Parts Outer Inner Handgrips - 2 Shock Set - 2 Left Right Handlebar Handlebar Mirror Clamp Windshield Right Mirror Left Mirror Mirror Lens - 2 Taillight Cover Taillight Fender Tip Handlebar Harness...
- Page 7 Parts Hex Bushing - 4 Axle Bushing - 2 12 Volt Charger 12 Volt Battery Round Bushing - 2 Not Shown: Label Sheet #8 x " Plastite Screw – 68* .437 (Large Diameter) Cap Nut - 4* .354 (Small Diameter) Cap Nut - 2* #8 x "...
-
Page 8: Parts Diagram
Vehicle Frame Vehicle Body Seat Wheel - 2 Gas Tank Left Footboard Exhaust - Inner - 2 Exhaust - Outer - 2 12 Volt Battery Axle Bushing - 2 Hex Bushing - 4 Wheel Axle - 2 Saddlebag - 2 Steering Bushing - 2 Front Headlight Rear Headlight... -
Page 9: Battery Charging
ELECTRICAL HAZARD WARNING • Battery can fall out and injure a child if vehicle tips over. Always use battery clamp. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. - Page 10 Battery • Using a Phillips screwdriver, loosen the two screws holding the battery clamp to the vehicle body. • Remove the screws and the battery clamp. Set the battery clamp and screws aside. Do not throw out the battery clamp or screws. You will use them when installing your battery (see page 28).
-
Page 11: Assembly
Children can be harmed by small parts, sharp edges and sharp points in the vehicle’s unassembled state, or by electrical items. Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, including the battery, or help in assembly of the vehicle. Vehicle Body •... - Page 12 Large Rectangular Opening Square Opening High Speed Hook-Up • Position the vehicle body on top of the vehicle frame. • Fit motor harness connector up through the large rectangular opening in the vehicle body. • Fit the high speed hook-up connector through the square opening near the front of the vehicle body.
- Page 13 Right Footboard • The right footboard was inserted in the vehicle frame at the factory. Make sure the right footboard is in place. • Insert two #8 x " screws into the right footboard as shown. Tighten the screws with a Phillips screwdriver. Do not over-tighten.
- Page 14 Right Exhaust Pipe • With the holes aligned, insert six #8 x the two halves of the right exhaust pipe. • Tighten the screws using a Phillips screwdriver. Do not over-tighten. • Repeat steps 9 through 12 to assemble the left exhaust pipe (L) to the left side of the vehicle.
- Page 15 Axle Bushing Groove Rear Fork Arm Wheel (with Hex Bushings) Back View • Position the vehicle assembly so that the back is facing you. • While holding the hex bushings in place, position the wheel between the rear fork arms of the vehicle frame. •...
- Page 16 Flashing Light Lens Notch Light Base Notch • Place the flashing light lens on the light base. Align the notch in the flashing light lens with the notch in the light base. Flashing Light Assembly Notch Groove Front Headlight Assembly •...
- Page 17 “Lens” • Turn the headlight assembly over so that the front faces you. Insert two #8 x " screws into the headlight assembly. • Tighten both screws using a Phillips screwdriver. Do not over-tighten. Front Fork • Position the headlight assembly front side down on a flat surface.
- Page 18 Handlebar Harness Right Handlebar • Locate the right handlebar. The right handlebar has an additional hole in the grip area. • Slide the base end of the wire cover (with handlebar harness) onto the right handlebar. Right Handlebar Wire Cover •...
- Page 19 Left Mirror Left Handlebar • Fit the left mirror to the left handlebar, as shown. • Fit and hold the mirror clamp to the other side of the left handlebar. • Insert two #8 x " screws through the back of the left mirror and into the mirror clamp.
- Page 20 Handlebar Assembly • Position the handlebar assembly face down. • Position the windshield curved side down. • Slide the windshield down over the headlight assembly. • Insert four #8 x " screws through the front fork and into the windshield. Tighten screws using a Phillips screwdriver.
- Page 21 Neck of Vehicle Body Handlebar Steering Assembly Stop • Fit the tab on the steering stop into the curved slot in the lower steering bushing • Hold the steering stop in place. • Slide the handlebar assembly on the neck of the vehicle frame and over the steering stop .354"...
- Page 22 Handlebar Harness Wire Clip Inset • Insert the handlebar harness into the wire clip on the side of the vehicle body. Assembly Battery Compartment Sound Box Handlebar SHOWN ACTUAL SIZE Harness • Loosen the screw in the sound box battery compartment door using a Phillips screwdriver and open the battery compartment.
- Page 23 Gas Tank Tabs Vehicle Body • Balance the light and sound box on the vehicle body. (The speaker should face down.) • Fit the tabs at the bottom of the gas tank under the front end of the vehicle body. •...
- Page 24 Handlebar Front Fork Tabs • Position the vehicle upside down. • Note the arrow on the underside of the front fender. • Position the front fender so that the arrow points towards the front of the vehicle. Slide the fender onto the ends of the handlebars.
- Page 25 Wheel (with Hex Bushings) Shock Wheel Axle Hex Bushings • Fit two hex bushings into the center hole in the remaining wheel. • While holding the hex bushings in place, position the wheel between the shocks. • Continue to slide the wheel axle through the wheel. Ring Side .437"...
-
Page 26: Label Decoration
Proper label application will help to keep the labels looking their best! When applying labels, keep the following guidelines in mind: • Wash your hands before applying the labels. • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. •... - Page 27 Label Decoration Right Side Left Side...
-
Page 28: Battery Installation
IMPORTANT! Use only Power Wheels Use of any other battery will damage your vehicle. Make sure that you charge the battery for at least 18 hours using the enclosed Power Wheels ® 12 volt charger before operating your vehicle for the first time. Charge the battery for at least 14 hours after each use of the vehicle. -
Page 29: Battery Care And Disposal
Battery Care and Disposal Care If a battery leak develops, avoid contact with the leaking acid and place the damaged battery in a plastic bag. See information below for proper disposal. If acid comes in contact with skin or eyes, flush with cool water for at least 15 minutes and call a physician. -
Page 30: Rules For Safe Driving
RIDING HAZARD WARNING Prevent Injuries and Deaths • Direct Adult Supervision Required. • Keep Children Within Safe Riding Areas These areas must be: - away from swimming pools and other bodies of water to prevent drownings. - generally level to prevent tipovers. - away from steps, driveways, roads and alleys. -
Page 31: How To Operate Your Vehicle
IMPORTANT! As assembled, your vehicle is ready to roll in low speed (2 your child is ready to drive the vehicle in high speed (5 mph, maximum), follow the instructions on this page to connect the high speed hook-up and use the power boost button. Beginner Use - Low Speed Drive •... -
Page 32: Mfcc Note (United States Only)
How to Operate Your Vehicle Advanced Use - High Speed IMPORTANT! Your child should not drive the vehicle in HIGH SPEED from a stopped position. Always start in LOW SPEED. Then, press the power boost button to shift to HIGH SPEED. Power Boost Button •... -
Page 33: Problems And Solutions Guide
Problems and Solutions Guide IMPORTANT! If you experience a problem with your vehicle, first check the Problems and Solutions Guide below. If you still experience a problem, please contact Power Wheels toll-free at 1-800-348-0751 between 8 AM and 6 PM (EST) Monday through Friday. Or, contact your local Power Wheels Authorized Service Center list beginning on page 36, or register on-line at www.powerwheels.com. - Page 34 Problems and Solutions Guide Problem Vehicle was running but Loose wire or loose connectors suddenly stopped Tripped thermal fuse Short run time (Less than Undercharged battery 1 - 3 hours per charge) Overcharged battery Battery is old and will not accept full charge Tripped thermal fuse Vehicle runs sluggishly...
- Page 35 Problems and Solutions Guide Problem Problem Vehicle runs sluggishly (cont.) Battery needs charging Battery is old and will not accept accept full charge Vehicle is overloaded Driving conditions are too stressful Vehicle runs in low speed but High speed hook-up does not run in high speed not connected Note: The vehicle is designed...
-
Page 36: Authorized Service Centers
We are continually expanding our Authorized Service Center Network. Please check this listing for the Authorized Service Center nearest you. If there is not one in your area, please call Power Wheels ® Consumer Relations at 1-800-348-0751. ALABAMA BIRMINGHAM - Frigid Service & Sales, 701 Graymont Ave. - Page 37 FAIRVIEW HEIGHTS - Rapid Rentals, 720 Lincoln Highway, 62087, (618) 632-0630 GRANITE - Midwest Golf Car & Equipment Co., 904 Thorngate Road, 62040, (618) 797-2278 HAMILTON - Discount Battery Sales, #80 S 2nd Rte. 136, 62341, (217) 847-3242 JACKSONVILLE - Rexx Battery Specialists, 847 South Main Street, 62650, (217) 245-2713 LINCOLN - Rexx Battery Specialists, 504 Keokuk, 62656, (217) 732-2885...
- Page 38 NEVADA LAS VEGAS - Burney’s Commercial Service, Inc., 4480 Aldebaran Avennue, 89103, (702) 736-0006 MINDEN - Valley Home & Sport Center, 1587 Highway 395, 89423, (775) 782-5111 NEW HAMPSHIRE MARLBOROUGH- Electronics Aid Inc., 32 Roxbury Road P.O. Box 325, 03455, (603) 876-4161 NEW JERSEY DENVILLE- Ranft's Denville Vacuum &...
- Page 39 FORT MILL - Service Engines Inc., 3356 SC Highway 51, 29715, (803) 548-1778, (800) 845-1191 GREENWOOD - Bikes & Boards & Mopeds, 203A Montague Avenue, 29646, (864) 229-2453 SENECA - Seneca Micronics, 110 East North First, 29678, (864) 882-6593 SOUTH DAKOTA RAPID CITY - Mick's Electric, Inc, 1304 Oregon Street, 57701, (605) 348-2335 WINNER - Nelson’s Electronics Inc., 422 West 2nd...
- Page 40 IMPORTANT! DO NOT use this vehicle for the first time until you have charged the battery for 18 hours. Remember to… Charge the battery immediately after each use. Charge the battery once a month during storage, even if the vehicle has not been used. Failure to follow these instructions will permanently damage your battery and void your warranty.