Install Anti-Tip Boards; Connect Water Supply - Thermador KBULT3651A Installation Instructions Manual

3. Stand the refrigerator up by first placing the left bottom edge
of the refrigerator on the floor, standing the refrigerator
upright, and then lowering the right-hand side of the
refrigerator down to the floor.
4. Reassemble the trim and top grille after the dolly has been
removed from the refrigerator.
I n s tal l A nt i -T i p B o ards
IMPORTANT:
The solid soffit must be within 1 in. (2.5 cm) maximum above
the refrigerator. If the solid soffit is higher than 1 in. (2.5 cm) or
one is not available, prevent the refrigerator from tipping
during use as shown.
It is recommended that board(s) be installed before the
refrigerator is installed.
Board(s) must be long enough to fully cover the width of the
compressor cover.
Locate the board(s) so the bottom surface(s) of the board(s)
is(are) 84 in. (213 cm) from the floor.
During installation, raise the refrigerator up so there is
in. (6.35 mm) maximum between the top of the refrigerator
and the bottom of the anti-tip board(s). Do not crush the
condenser cover when raising the rear leveling legs.
To install anti-tip boards
1. Mark the stud locations on rear wall 80 in. to 90 in. (203 -
229 cm) above floor.
2. Securely attach one or two 2 in. x 4 in. x 32 in.
(5 cm x 10 cm x 81 cm) wood boards to wall studs behind
refrigerator. Use 6 - #8 x 3 in. (7.6 mm) (or longer) wood
screws. The wood screws must be screwed into the studs at
least 1½ in. (3.8 cm). The board(s) must overlap the
compressor cover.
2" (5 cm)
4
1. Center board in. (6.35 mm) max. above refrigerator
2. Two 2 in. x 4 in. x 32 in. (5 cm x 10 cm x 81 cm) boards
3. Attach to studs with 6 -#8 x 3 in. (7.6 cm) screws
4. Compressor cover
16
1 2
3
C o nn e c t Wa t e r S u p p l y
1. Remove the shipping tape from the gray, coiled water tubing
on the rear of the refrigerator.
2. Before attaching copper tubing to the refrigerator, flush at
least 2 qt. (1.9 L) of water through the copper tubing and into
a bucket to get rid of any particles in the water line.
3. Check for leaks around the saddle valve. Do not overtighten
the clamp or sleeve. This will crush the copper tubing.
4. Make connection to the refrigerator.
Style 1 - Connecting to a Water Valve:
NOTE: The water shutoff valve should be located in the base
cabinet on either side of the refrigerator. The right-hand side
is recommended. The access hole through the right cabinet
must be within in. (12.7 mm) of rear wall.
Push the bulb end of the tubing into the water valve as far as
it will go. Slide the nut forward and finger tighten. Then
tighten it with a wrench two more turns. Do not overtighten.
1. Bulb
2. Nut (provided)
Style 2 - Connecting to a Water Line
Additional Parts Needed: Coupling, ferrule and nut.
Slide the purchased nut then the purchased ferrule onto the
tubing. Push the tubing into the purchased coupling as far as
it will go. Slide the nut and ferrule forward. Tighten the nut by
hand. Then tighten it with a wrench two more turns. Do not
overtighten.
1 2 3
1. Line to refrigerator
2. Nut (provided)
3. Bulb
5. Turn shutoff valve ON.
6. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
1
2
4 5 6
4. Coupling (purchased)
5. Ferrule (purchased)
6. Nut (purchased)