Related Manuals for Samsung SHR-3010P
Summary of Contents for Samsung SHR-3010P
-
Page 1: Digital Video Recorder
DIGITAL VIDEO RECORDER SHR-3010 User’s Manual CLASS A (For Business) To use this product safely, have to read “Important Safety Introductions”, and then be well aware of the contents. -
Page 2: Important Safety Instructions
DIGITAL VIDEO RECORDER Important Safety Instructions 1. Read these instructions. CAUTION 2. Keep these instructions. RISK OF ELECTRIC SHOCK DO NOT OPEN 3. Heed all warnings. 4. Follow all instructions. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO 5. -
Page 3: Table Of Contents
Contents Important Safety Instructions IV. Record 1. Basic Record Contents 2. Record Lock 3. Alarm Record 4. Reservation Record I. Summary 1. Introduction V. Retrieval and Playback 2. Characteristics 3. Name and Function of Each Part 1. Retrieval Menu View 4. - Page 4 I. Summary...
-
Page 5: Introduction
Besides English, multi-language support provides German, French, Spanish, and Italian. You can back up data with SCSI. You can control the camera and select channels with the Remote Viewer Program. (For SAMSUNG model only :SCC-641, 643 Camera, SCC-421 Series (C4201, C4203,C 4301, C4303) Camera, SDM-160 Multiplexer) -
Page 6: Name And Function Of Each Part
DIGITAL VIDEO RECORDER Name and Function of Each Part Front View Name Function Name Function Displays system status. Used when moving cursor to the lower item of menu or DOWN ( POWER : Checks power On. reducing values in setting-up details of menu. : Checks normal access to HDD. - Page 7 DIGITAL VIDEO RECORDER Rear View Name Function Name Function EXTERNAL I/O ALARM IN: In the N.C. (Normally Closed) mode, the system RS232 PORT Serial Port for remote control. recognizes an alarm when a High (5V) signal is input for over PORT 0.5 seconds.
-
Page 8: Unpacking
DIGITAL VIDEO RECORDER Unpacking HDD Addition When purchasing product, first remove packing and put it on a flat floor or at a place to use it. Mounting HDD Then, ensure all following contents are included: 1. Unfasten the SCREW-SPECIAL (BWH, M4, L8, WHT) 11 EA attached to the left, right, Main body and rear of the product, and then remove the CABINET-TOP from the product. - Page 9 DC Power in the Master Mode, when mounting a new hard disk drive it can be set in the Slave Mode. Connector For example, mode is set as follows in case of Samsung Spinpoint V80 HDD: Power Supply Cable (4Pin) If successfully mounting the HDD on the product and then booting the system, the system recognizes that a new HDD is mounted and starts to operate after formatting the first HDD.
-
Page 10: Connection With Other Devices
II. Connection with Other Devices... -
Page 11: Connection To External Devices
DIGITAL VIDEO RECORDER Connection with Multiplexer Connection to External Devices (e.g. connection to SDM-160) CAMERA TRIGGER OUT MICROPHONE ALARM IN CAMERA SIREN LIGHT MONITOR SHR-3010 VIDEO RECORDER AC IN SDM-160 DIGITAL MULTIPLEXER VIDEO IN VIDEO OUT SDM-160 is a Multiplexer for NTSC, and SDM-160P is a Multiplexer for PAL. VIDEO OUT SHR-3010 VIDEO RECORDER AUDIO OUT... -
Page 12: System Connection For Alarm Recording
DIGITAL VIDEO RECORDER System Connection for Alarm Recording Connection with PC for Use Connection with RS-232C <Rear Side Connection Terminal of SHR-3010> <Outside Product> A. Communication Method Data Code: ASCII Code Protocol: 8 bit Data, 1 Stop bit, None Parity Transmission speed: 4800, 9600, 19200, 38400 bps B. - Page 13 Dest.Addr. 0x0A 0x0C 0xFF Check Sum 0x0C F.Shuttle 2 0xA0 Src.Addr Dest.Addr. 0x0A 0x0D 0xFF Check Sum 0x0D C. Data Format (Samsung Protocol) F.Shuttle 3 0xA0 Src.Addr Dest.Addr. 0x0A 0x0E 0xFF Check Sum 0x0E F.Shuttle 4 0xA0 Src.Addr Dest.Addr. 0x0A...
-
Page 14: Basic Method To Use
III. Basic Method to use... -
Page 15: Booting The System
DIGITAL VIDEO RECORDER Booting the System Power On There is a power switch on the upper right hand side behind the system. Pull the power Recognizing incoming video signal switch up to boot the system. Then, the LED on front of the system is turned on, a blue SHR-3010 system can automatically recognize whether the video signal connected at the input port screen with the following message will appear and the system is booted. -
Page 16: Basic Screen Viewing
DIGITAL VIDEO RECORDER Basic Screen Viewing Viewing Full Screen And the system will automatically keep on searching for a hard disk drive as shown below. If you attach a hard disk drive at this time, the system will recognize the hard disk drive, the Here comes the description of all the icons and status in the screen. - Page 17 DIGITAL VIDEO RECORDER Live Screen Viewing The normal Live screen looks like this. 2001-09-15 07:14:55 2001-08-22 18:19:12 It shows the current date and time as configured by the system. If system is in the recording state icon will blink. However, it does not blink in the You can change the display position of date and time.
- Page 18 DIGITAL VIDEO RECORDER Viewing Screen during recording Playback screen Viewing The normal recording screen looks like this. The normal Playback screen looks like this. 2001-08-22 18:19:12 2001-09-24 00:23:44 The upper pointer shows the relative location of the recorded data being stored inside If the system is executing the recording function, icon blinks.
-
Page 19: Menu View
DIGITAL VIDEO RECORDER Menu View Menu Enter Change of Settings Press a MENU button. Then, following screen appears. Move to desired menu item by using an UP( ) or a DOWN( ) button. You can change settings by pressing the SET/STILL( ) button. - Page 20 DIGITAL VIDEO RECORDER Example of menu setting (in case of changing time) Similarly, press the UP( ) or DOWN( ) button so current minute is displayed. Then if pressing the LEFT( ) or RIGHT( ) button, the cursor is changed so hour or Press the MENU button and then press the SET/STILL( ) button when the cursor second is changed.
-
Page 21: Setting Of Date, Time And Screen
DIGITAL VIDEO RECORDER Setting of Date, Time and Screen Each menu item CLOCK/DISPLAY MODE SETUP SYSTEM SETUP The following illustrates the intial setting of the CLOCK/DISPLAY MODE SETUP menu. CLOCK/DISPLAY MODE SETUP SYSTEM SETUP PASSWORD **** DATE 2002-01-01 PASSWORD LOCK TIME 12:00:00 HDD ERASE... -
Page 22: Record Setup
DIGITAL VIDEO RECORDER Record Setup Note Note The following illustrates the intial setting of the RECORD MODE SETUP menu. The following table shows how long it takes to fill the 40GB HDD with respect to each field rate when the video signal is NTSC and PAL respectively. RECORD MODE SETUP (Recording time for each field rate may slightly vary depending on the type of input AUDIO RECORD... -
Page 23: Alarm Record Setup
DIGITAL VIDEO RECORDER Alarm Record Setup DISK END BUZZER The following illustrates the intial setting of the ALARM RECORD SETUP menu. If set to ON, the Buzzer will sound when the HDD is full during the recording; if set to OFF, the Buzzer will not sound. - Page 24 DIGITAL VIDEO RECORDER PRE ALARM TIME LIMIT MOTION DETECTION The pre-alarm recording is an important function which enables you to find out about the situation The DVD will start recording images whenever it detects any movement only when ALARM immediately before a motion is detected in the input video or before alarm occurs. Set how much ENABLE is set to ON.
-
Page 25: Reservation Record Setup
DIGITAL VIDEO RECORDER Reservation Record Setup The following illustrates the intial setting of the TIMER RECORD SETUP menu. AREA=2 LEVEL=OFF [SIZE][MOVE] TIMER RECORD SETUP TIMER START FIELD RATE AREA 2 --:-- --:-- --.-- --:-- --:-- --.-- --:-- --:-- --.-- --:-- --:-- --.-- --:-- --:-- --.--... -
Page 26: System Setup
Multiplexers are SAMSUNG SDM-160(SDM-090), SMO-150(SMO-210, SOM-080). controlled. But, this remote control shall be applied only to SEC SCC-641, 643 Camera, and SCC-421 Series (C4201, C4203, C4310, C4303) Camera which use the SAMSUNG LANGUAGE (MULTI-LANGUAGE SUPPORT) Protocol. You can select the camera to be controlled by the remote monitoring program. -
Page 27: System Information
DIGITAL VIDEO RECORDER S ystem Information B ackup Setting (SCSI HDD BACKUP) The following illustrates the intial setting of the SYSTEM INFORMATION menu. You shall connect this DVR to an external SCSI HDD with a connector to backup or replay the video or audio signal stored in the main body HDD. - Page 28 DIGITAL VIDEO RECORDER START (Starting Backup) TIME RANGE Press the SET/STILL button( ), and the wordletter “SEARCH” will appear. FROM DATE 2003.04.02 TIME 13:27:39 It will start to backup after finding the image data from the HDD to backup from the HDD. DATE 2003.04.02 TIME...
- Page 29 DIGITAL VIDEO RECORDER (2)BACKUP FROM ALARM EVENT LIST (3) SEARCH & PLAY OF BACK UP (Backup image search and replay) BACKUP FROM ALARM EVENT LIST is forto backing up the image and voice data of SEARCH & PLAY OF BACKUP is used to search and replay the image backed up in the the time when the alarm event occurred, by alarm or detection of movement, to the external SCSI HDD.
- Page 30 DIGITAL VIDEO RECORDER (4) SCSI ERASE (SCSI HDD Recording Deletion Mode Setup) SCSI ERASE in the BACKUP SET UP menu is used to erase all the image signal backed up in the SCSI HDD. Press the JOG( ) or UP( ), DOWN( ) button to move the cursor until SCSI ERASE is highlighted.
-
Page 31: Record
IV. Record... -
Page 32: Basic Record
DIGITAL VIDEO RECORDER Basic Record Basic Record RECORD STOP Press the STOP( ) button for 3 seconds to stop recording. Then, the light will go off in CURRENT IMAGE RECORD the RECORD( ) button and recording will stop with the following message on the Press the RECORD( ) button to record current image. -
Page 33: Record Lock
DIGITAL VIDEO RECORDER Record Lock Alarm Record Record Lock Record in Alarm Occurrence Press the REC LOCK button during recording to lock the recording. Then, the LOCK status There is an alarm input terminal (ALARM IN) on the external I/O port at the back panel of indicator LED and the REC LOCK button will light up. -
Page 34: Reservation Record
DIGITAL VIDEO RECORDER Reservation Record Reservation Record Setup You can enter the day, time, and field rate for the timer recording in the TIMER RECORD SETUP menu so that the recording will be made on the set day for the set amount of time. Reservation Record Cancel V. -
Page 35: Retrieval Menu View
DIGITAL VIDEO RECORDER Retrieval Menu View Upper Menu Move and Menu End Retrieval Menu Enter Press the SEARCH button to move from the lower menu to the upper menu or end menu. Press the SEARCH button to retrieve recorded data. If doing so, following screen appears. -
Page 36: Recorded Data List View
DIGITAL VIDEO RECORDER Retrieval by Date and Time Recorded Data List View DATE & TIME SEARCH RECORD EVENT SEARCH [01/04] EVENT DATE TIME DATE 2002-01-01 01 RECORD START 2001-09-24 00:23:28 TIME 00:00:00 02 RECORD START 2001-09-24 00:30:00 [SEARCH START] 03 RECORD START 2001-09-24 01:49:31 04 RECORD START 2001-09-24 02:00:00 EXIT=[SEARCH] SEARCH=[SET/STILL] EXIT=[SEARCH] SEARCH=[SET/STILL]... -
Page 37: Alarm Record Retrieval
DIGITAL VIDEO RECORDER Alarm Record Retrieval Power On/Off Status List View ALARM EVENT SEARCH [01/03] POWER EVENT LIST [01/08] EVENT DATE TIME EVENT DATE TIME 01 ALARM START 2001-05-11 09:23:55 01 POWER OFF 2001-09-24 00:00:52 02 ALARM START 2001-05-14 15:22:13 02 POWER ON 2001-09-24 00:07:38 03 POWER OFF 2001-09-24 00:11:56... -
Page 38: Basic Playback
DIGITAL VIDEO RECORDER Basic Playback Press the PLAY( ) button to immediately play back the data recorded on the HDD. Then, the The light of SET/STILL( ) button turns and the light of the PLAY( ) button flickers if PLAY ( ) button lights up, the following screen appears, and the beginning of the recorded pressing the SET/STILL( ) button during play. -
Page 39: Various Screen View Using Jog/Shuttle
DIGITAL VIDEO RECORDER Various Screen View Using JOG/SHUTTLE Play in Various Speed Temporay Stil Screen View The data recorded on the HDD will be played back as it is recorded. For example, if the Press the SET/STILL( ) button during playback. PICTURE QUALITY of the RECORD MODE SETUP is set to NORMAL and if the record- (For details on the pause mode, refer to “6. -
Page 40: Vi. Others
VI. Others... -
Page 41: Product Standards
DIGITAL VIDEO RECORDER Product Standards Appearance Drawing Rated Voltage AC 110 ~ 240V, 50/60 Hz Power Consumption 80 GB Basic Installation (Simultaneous Installation of Max. 2 HDDs) BACKUP External SCSI II Interface(SCSI HDD) Video Input Composite Video, BNC Jack - 1CH (1.0 Vp-p, 75 ) Video Output Composite Video, BNC Jack - 1CH (1.0 Vp-p, 75 Audio Input... -
Page 42: Vii. Appendices
VII. Appendices... - Page 43 DIGITAL VIDEO RECORDER Check Points before Call Service Center If the system malfunctions, please check the following instruction before you call the service center or the shop where you bought the system. Trouble Check Points Trouble Check Points • Unable to supply power. –...
- Page 44 DIGITAL VIDEO RECORDER Q & A Question Answer • Does recording continues after power cut – Without power supply, the system can't perform during recording. recording. But if the system was recording before power cut, it will resume recording upon power supply.
- Page 45 www.securitysamsung.com AB68-00377A Printed in Korea...