DIGITAL VIDEO RECORDER User’s Manual To use this product safely, have to read “Important Safety Introductions”, and then be well aware of the contents. SHR-3010...
DIGITAL VIDEO RECORDER CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside.
Contents 3-14 3-15 3-18 3-22 3-23 3-24 3-25 3-26 Important Safety Instructions Contents I. Summary 1. Introduction 2. Characteristics 3. Name and Function of Each Part 4. Unpacking 5. HDD Addition II. Connection with Other Devices 1. Connection to External Devices 2.
DIGITAL VIDEO RECORDER Introduction The Digital Video Recorder SHR-3010 is a Digital Time Lapse Recorder to utilize its HDD as a recording media. How to use it is simple and therefore existing users of Time Lapse VCR can also access to it since it is built with Jog/Shuttle. You can also perform continuous recording on the HDD and directly view image recorded without turning videotapes as in the existing Time Lapse VCR.
DIGITAL VIDEO RECORDER Name and Function of Each Part Front View Name Displays system status. POWER : Checks power On. FULL STATUS ALARM : Check Alarm turns operates. DISPLAY LED LOCK Used when displaying menu for setting-up systems or MENU entering from the sub menu to the top menu.
Page 7
DIGITAL VIDEO RECORDER Rear View Name RS232 PORT Serial Port for remote control. RS485 PORT Serial Port for remote control. Composite image signal I/O terminal (BNC Style Connector). VIDEO IN/OUT Audio Signal Input/Output Jacks (RCA Jacks). AUDIO IN/OUT LAN Cable Connection Terminal. MODE It is the DIP switch to set System ID, Direct Communication, Termination, etc.
DIGITAL VIDEO RECORDER Unpacking When purchasing product, first remove packing and put it on a flat floor or at a place to use it. Then, ensure all following contents are included: ◗ Main body ◗ User’s Manual ◗ 1 power cord ◗...
Page 9
Slave Mode. Basically, since the hard disk drive mounted on the product is in the Master Mode, when mounting a new hard disk drive it can be set in the Slave Mode. For example, mode is set as follows in case of Samsung Spinpoint V40 HDD: Master Mode...
– A CRT monitor capable of displaying an NTSC or PAL video signal must be used with this unit. An ordinary computer monitor cannot be used. – The backup device of this equipment is applicable only to SCSI HDDs. MICROPHONE SHR-3010 VIDEO RECORDER Connection with Multiplexer (e.g. connection to SDM-160) TRIGGER OUT...
DIGITAL VIDEO RECORDER System Connection for Alarm Recording <Rear Side Connection Terminal of SHR-3010> ALARM IN ALARM RESET ALARM OUT TRIGGER OUT Alarm recording is a function for recording the input video when an alarm signal is input while a device with alarm output is connected to this unit.
Page 13
Protocol: 8 bit Data, 1 Stop bit, None Parity Transmission speed: 4800, 9600, 19200, 38400 bpss B. RS-485 terminal and Pin specifications DATA + DATA - C. Data Format (Samsung Protocol) 9 Byte Fixed Start Code (A0H) Start Addr. Target Addr.
2001-09-15 17:14:55 Recognizing incoming video signal SHR-3010 system can automatically recognize whether the video signal connected at the input port is NTSC or PAL signal upon booting the system. When you turn the system on, it will recognize if the image signal is NTSC or PAL automatically to set itself to the signal.
DIGITAL VIDEO RECORDER And the system will automatically keep on searching for a hard disk drive as shown below. If you attach a hard disk drive at this time, the system will recognize the hard disk drive, the boot process will end, and a live screen will appear. SYSTEM UNSTABLE OR HDD NOT EXIST RESET HDD DEVICE(S) >TRY TO FIND HDD...
Page 17
DIGITAL VIDEO RECORDER 2001-08-22 18:19:12 It shows the current date and time as configured by the system. You can change the display position of date and time. You shall designate the position in the top right or left corner by yourself. (Just choose LEFT or RIGHT in the CLOCK/DISPLAY MODE SETUP menu.
Page 18
DIGITAL VIDEO RECORDER Viewing Screen during recording The normal recording screen looks like this. If the system is executing the recording function, If the system is in the recording state due to alarm, icon continually blinks. If the system is in the recording state due to Motion Detection, In this state, icon continually blinks.
DIGITAL VIDEO RECORDER Menu View Menu Enter Press a MENU button. Then, following screen appears. MAIN MENU CLOCK/DISPLAY MODE SETUP RECORD MODE SETUP ALARM RECORD SETUP TIMER RECORD SETUP SYSTEM SETUP COMMUNICATION SETUP SYSTEM INFORMATION BACKUP SETUP Note Note You can go into the menu only when the system is in the Live screen mode. If the system is in the recording mode or playback mode, you cannot go into the menu.
Page 20
DIGITAL VIDEO RECORDER Example of menu setting (in case of changing time) Press the MENU button and then press the SET/STILL( points out the CLOCK/DISPLAY MODE SETUP. Then following screen appears. CLOCK/DISPLAY MODE SETUP DATE TIME DATE DISPLAY TYPE DATE & TIME DISPLAY DATE &...
DIGITAL VIDEO RECORDER Each menu item CLOCK/DISPLAY MODE SETUP CLOCK/DISPLAY MODE SETUP DATE 2002-01-01 TIME 12:00:00 DATE DISPLAY TYPE YYYY-MM-DD DATE & TIME DISPLAY DATE & TIME POSITION RIGHT STATUS DISPLAY STATUS POSITION LEFT RECORD MODE SETUP RECORD MODE SETUP AUDIO RECORD PICTURE QUALITY NORMAL...
DIGITAL VIDEO RECORDER Record Setup The following illustrates the intial setting of the RECORD MODE SETUP menu. RECORD MODE SETUP AUDIO RECORD PICTURE QUALITY PICTURE RATE DISK END MODE DISK END BUZZER RECORD TIME MARK TIME MARK POSITION x AUDIO RECORD Set to ON to record video and audio at the same time, or set to OFF to record video only.
DIGITAL VIDEO RECORDER ➄ DISK END BUZZER If set to ON, the Buzzer will sound when the HDD is full during the recording; if set to OFF, the Buzzer will not sound. [ON/OFF] ➅ RECORD TIME MARK If set to ON, the recording time will be displayed during playback; if set to OFF, it will not be displayed.
Page 24
DIGITAL VIDEO RECORDER ➄ PRE ALARM TIME LIMIT The pre-alarm recording is an important function which enables you to find out about the situation immediately before a motion is detected in the input video or before alarm occurs. Set how much video data you want to record before the motion is detected or alarm is triggered.
DIGITAL VIDEO RECORDER AREA=2 LEVEL=OFF AREA 2 3) SIZE Set the size of the area currently selected. Press the UP( the area vertically, or press the DOWN( ) button to decrease the size of the area vertically. Press the RIGHT( ) button to increase the size of the area horizontally, or press the LEFT( ) button to decrease the size of the area horizontally.
DIGITAL VIDEO RECORDER System Setup The following illustrates the intial setting of the SYSTEM SETUP menu. SYSTEM SETUP PASSWORD PASSWORD LOCK HDD ERASE FACTORY RESET MENU SCREEN LANGUAGE x PASSWORD Set the system password. You can enter a 4-digit number and the initial set value is 0000. y PASSWORD LOCK If you set this to ON, you can ask for a password, which is set in the PASSWORD, each time the MENU button is pressed or the recording lock cancellation is attempted during the...
S CSI HDD BACKUP You shall connect this DVR to an external SCSI HDD with a connector to backup or replay the video or audio signal stored in the main body HDD. The external SCSI HDD is the only backup device of this DVR.
Page 28
Caution Caution – During the SCSI backup process, you may not record or replay data in the DVR main body HDD nor you may communicate through LAN. – The date and time in the backup screen indicates the time when the main body starts recording in the HDD.
Page 29
DIGITAL VIDEO RECORDER (2)FROM RECORD EVENT LIST (Backup by the record event list) When you press the RECORD key in the main body HDD for recording or you have recorded data for long, the event list will be created at an interval. If you use this function for recording, you will be able to locate the backup position more conveniently than TIME RANGE BACKUP.
Page 30
DIGITAL VIDEO RECORDER (4) SEARCH & PLAY OF BACK UP (Backup image search and replay) SEARCH & PLAY OF BACK UP is used for the search and replay of the backup data in the SCSI HDD. The following screen shows the detailed setup procedure of SEARCH & PLAY OF BACK UP and the EVENT(RECORD START), date, and time in the following screen are based on the HDD recording.
DIGITAL VIDEO RECORDER Basic Record Basic Record x CURRENT IMAGE RECORD Press the RECORD( ) button to record current image. If doing so, the light of the RECORD( ) button turns on and record starts while following message appears on the screen.
There is an alarm input terminal (ALARM IN) on the external I/O port at the back panel of the SHR-3010 system. Connect here the alarm output terminal of an external device, such as Multiplexer. (For detailed information on connections, please refer to “3. System Connection for Alarm Recording”...
DIGITAL VIDEO RECORDER Reservation Record Reservation Record Setup You can enter the day, time, and field rate for the timer recording in the TIMER RECORD SETUP menu so that the recording will be made on the set day for the set amount of time. Reservation Record Cancel If the system is not in the timer recording mode, in order to cancel the timer recording, set the TIMER row of the line you want to cancel to OFF in one of the timer recording list set...
DIGITAL VIDEO RECORDER Retrieval Menu View Retrieval Menu Enter Press the SEARCH button to retrieve recorded data. If doing so, following screen appears. SEARCH MENU DATE & TIME SEARCH RECORD EVENT SEARCH ALARM EVENT SEARCH POWER EVENT LIST Note Note - All recorded data can be searched if the system is in the Live screen mode, the recording mode, or the playback mode.
DIGITAL VIDEO RECORDER Retrieval by Date and Time DATE & TIME SEARCH DATE TIME [SEARCH START] EXIT=[SEARCH] SEARCH=[SET/STILL] Following screen appears and light of the PLAY( ) button after entering date and time to retrieve and placing the cursor at search. O SEARCH O »...
DIGITAL VIDEO RECORDER Alarm Record Retrieval ALARM EVENT SEARCH EVENT 01 ALARM START 2001-05-11 09:23:55 02 ALARM START 2001-05-14 15:22:13 03 ALARM START 2001-05-14 15:30:00 EXIT=[SEARCH] SEARCH=[SET/STILL] Among the data on the HDD, the ones that were recorded when a motion was detected or alarm was triggered will be displayed as a list based on the recording start time.
DIGITAL VIDEO RECORDER Basic Playback Press the PLAY( ) button to immediately play back the data recorded on the HDD. Then, the PLAY ( ) button lights up, the following screen appears, and the beginning of the recorded data is played back in turn. O PLAY O √...
DIGITAL VIDEO RECORDER Various Screen View Using JOG/SHUTTLE Play in Various Speed The data recorded on the HDD will be played back as it is recorded. For example, if the PICTURE QUALITY of the RECORD MODE SETUP is set to NORMAL and if the record- ing is made with the PICTURE RATE set to 5.00FPS, then a Normal quality video will be played back at 5 FPS as it is recorded.
DIGITAL VIDEO RECORDER Product Standards Rated Voltage AC 110 ~ 240V, 50/60 Hz Power Consumption 80 GB Basic Installation (Simultaneous Installation of Max. 2 HDDs) BACKUP External SCSI II Interface(SCSI HDD) Video Input Composite Video, BNC Jack - 1CH (1.0 Vp-p, 75Ω) Video Output Composite Video, BNC Jack - 1CH (1.0 Vp-p, 75Ω...
Page 43
DIGITAL VIDEO RECORDER Check Points before Call Service Center If the system malfunctions, please check the following instruction before you call the service center or the shop where you bought the system. Trouble • Unable to supply power. – Check the power cable connection behind the •...
Page 44
DIGITAL VIDEO RECORDER Q & A Question • Does recording continues after power cut – Without power supply, the system can't perform during recording. recording. But if the system was recording before power cut, it will resume recording upon power supply.
Page 45
www.securitysamsung.com AB68-00377A Printed in Korea...