Table of Contents
Advertisement
You can memorize receiver
settings,
and recall
at
the
touch of
a
button.
Two
memory
buttons
are
available.
lf
you connect
a
component bearing
the
pioneer
!t!=il
mark, such as
a
CD player,
to the
CONTROL OUT
jack on
the
rear panel, signals
can
also
be
transmitted to automatically
switch
on
power
and
start
play
of
that
component.
NOTE:
With
some components,
even
if
they bear
theffimark,
powet
cannot
be
switched
on and
off
by
remote control.
lOperating Memoryl
1.
Select
the settings
on
the
receiver
you
want to
memorize.
2.
Press
the
MEMORY
button.
o
After the
"AUTO
SOURCE CONTROL,,
indication
has
scrolled
in
the
display,
"MEMORY"
appears and flashes.
3.
Press
the AUTO
SOURCE CONTROL
burton
(1 or
2l
you
wanr
to
use
for
memorizingl.
3
orro
souRcE
coNrRoL
(1,2)
Example:
Using
the AUTO
SOURCE
CONTROL
1
bunon
to
memorize settings
to start
play on
a
CD player
connected to the
receiver,s CONTROL OUT
jack.
1.
Set
the
receiver INPUT
SELECTOR
to
CD.
2.
Adjust tone,
surround, and
other
parameters
to the settings
you
want to
memorize.
3.
Set
the volume to the
level
you want
to
memorize.
4.
Press
the
MEMORY
button.
5.
Press
the AUTO
SOURCE
CONTROL
1 button.
lRecallingl
Press
the
AUTO
SOURCE CONTROL
button
(1
or
2l
for
the
settings
you want
to
recall.
Remote control AUTO
SOURCE CONTROL
buttons
(1
or
2) can
also
be
used
to
recall settings.
"AUTO
SOURCE CONTROL
1
lor
2)"
is
scroil disptayed.
After the last
indication, such as
"PLAY CD"
has been
scroll displayed, the display
switches to function
indications.
ln
the
case
of the
example,
the following
operations are performed.
@
Press
the AUTO
SOURCE
CONTROL
1
button.
@
Power
to the receiver switches
ON,
the
INPUT SELECTOR
selects
CD, settings for such parameters
as
surround,
and
tone
are called
up, and power
to the
CD player
is
switched
ON.
@
Play
starts
on
the
CD
player.
@
Volume level is raised by
the
MASTER VOLUME on
the
receiver.
NOTE:
o
Memorized
volume level and recall volume level
may differ
by
a
small
amount.
c
lf
volume is near
minimum level when memorized, volume may
not
rise when
the
setting
is
recalled.
28
<AR81378>
NOTE:
.
Since the
power
ON and
play
signals
for
components bearing
the
ffimark
called by
Auto
source contml
are
output through
this
unit's
CONTROL OUT
jack,
be sure
to connect
the
control cord kefer
to
page 24).
.
With some
components,
even
if
they bear
theffimark,
powet cannot
be switched on and
off by
remote
contol.
tf
this
is
the
case,
by
connecting
the
other unit's
power
cord
to
this
unit,s
SWITCHED
AC
OUTLET,
and leaving the other unit's
power switch
ON,
power
switching will
depend
on whether
this
unit is
on or off.
c
Volume level can
not
be raised above the center setting.
.
AUTO
SOURCE CONTROL
memoty
stores the receiver settings
at
that
point
in
time;
it
does
not
memorize
STATTON
CALL numbers
11-3O),
CUSTOM MEMORY,
or
ACOUST\C MEMORY
(A_E,
LOUDNESS.
FLAN.
o
During
operation
of
AIJTO
SOIJRCE CONTROL,
other components
are also
being
controlled, so
do
not
perform
other
operations
until
it
is finished.
With
auto source
control,
power
ON/OFF
signals and
play
signals
are
output
from the CONTROL
OUT
jack
at
the times
shown
in
the
following
chart.
Function at
the
time
of
memorizing
POWER signal
PLAY
signal
PHONO
Yes
TUNER
No
No
CD
Yes
Yes
TAPE
1
Yes
Yes
TAPE 2
Yes
Yes
VCR
1
Yes
(VCR, TV)
Yes
(VCR
PLAY,
TV
FUNC
"LD")
VCR
2
Yes (VCR,
TV)
Yes
(VCR
PLAY, TV
FUNC
"LD")
LD
Yes (LD, TV)
Yes
(LD
PLAY, TV
FUNC
,'LD")
TV
Yes
(TV)
Yes
(TV FUNC
"TV")
Example
of
AUTO
SOURCE
CONTROL 1,
2
memory:
AUTO
SOURCE
CONTROL
Volume
lnput
selector
Surround mode
7
CD
DOLBY
PRO LOGIC
SURROUND
2
10
TV
STUDIO
o
F:
-
It---------------
l
e
-lrll^E
Hide quick links:
Advertisement
Table of Contents
