Table of Contents
Advertisement
Use
with
video or audio
sofrware
bearing
the D0
FaBy
sunnorrNp-l
mark.
Use
DOLBY PRO LOGIC
SURROUND
when
rear
speakers
are
connected,
and
DOLBY
3CH
LOGIC
when
rear
speakers
aren,t
connected.
For
correct surround reproduction,
be
sure
to
perform following
adjustments.
LEVEL
ADJUSTMENT
1.
Use SURROUND MODE
butrons
ro
setect
DOLBY pRO
LOGTC
SURROUND
or
use
the
DOLBY
3CH
LOGIC
burton
to
switch
DOLBY
3CH
LOGIC
ON.
2.
Use
SPEAKERS
button
to
turn
on
front
speakers.
3.
Adjust
MASTER VOLUME
to
a
suitable
listening
level.
4.
Press BALANCE
L
and
R
buttons togethel.
5.
SEIECT
thE CENTER
MODE (NOBMAL, WIDE, PHANTOM}
SEttiNg
with
the
remote
control
CENTER
MODE
button.
6.
Press
the lemote control
TEST TONE
button.
7.
With the remote conrrol BALANCE
(1, R), CENTER LEVEL
(+,
_),
and
REAR
LEVEL
(
+
,
-)
buttons,
adjust
the
test tone volume
level
so
that
is
the
same
from
each speaker.
8.
Press
the
remote control
TEST TONE
button to switch
the
test tone
OFF,
NOTE:
c
The
TEST TONE
turns
off
if
you operate the
lNpuT
SELECTOR.
.
CENTER
MODE
PHANTOM selection and
REAR LEVEL
adjustment
are not possible during DOLBY 3CH
LOGIC
operation.
OPERATION
1.
Select
DOLBY PRO
LOGTC
SURROUND
with
rhe
SURROUND
MODE
buttons, or
selecr DOLBY
3CH
LOGIC.
2.
Select
the component
for
playback
with
the
INpUT
SELECTOR
buttons.
3.
Select
the center
mode
with
the
remote
control
CENTER
MODE
button.
4.
Begin playback.
5.
Adjusr volume
level
with
the
MASTER VOLUME
control.
SETTING
THE DELAY TIME
When using DOLBY
PRO LOGIC SURROUND,
you
can set
the
delay
time between
16 ms and
30
ms (2 ms step). The standard
setting
is
20 ms, but you
can select any
setting of your
choice.
When you
press
the
DELAY
TIME
button
on
the
main
unit
or remote
control,
DELAY
lights
in
the display section,
with
numerical indication
of the
delay time.
Memorized
tone settings
can be recalled using
the
SELECT
button.
Up
to five different tone
settings can be memorized.
Setting the Acoustic Memory
2
1.
Adjust
the sound
quality
as
desired using
the
BASS and
TREBLE
control buttons.
.
Sefting
are
shown by the
TONE level indicator
on the
display
section,
2.
Press
the
MEMORY
butron.
.
The
acoustic memory letters
on
the display section
blinks
on
and
off.
3.
Press
the
SELECT
button
and select
the acoustic memory to
which
you wish
to
assign
the setting
(A
-
E).
.
The sound quality setting
is
memorized approximately
five
seconds
after you
last
press
the
SELECT
button.
zo
<AR81378>
ln
this
way,
the
desired
tone
will
be
preset
in
one of the five acoustic
memory positions. To
preset
four other
desired
tone settings, perform
the
same operations.
Recalling
tone setting in the Acoustic Memory
To
recall
the memorized tone settings,
press
the
SELECT
button
to
select
the
desired memory position.
r--+ FLAT*
LOUDNESS*
A
*
B
_
C
_ D_
E
.-
FLAT:
For
flat
(normal) frequency
response.
LOUDNESS: Emphasizes
the low-
and
high-frequency
ranges.
Produces
a
fuller
sense
of
sound, particularly
when
listening
at low
volume.
Memorized acoustic memory settings.
A-E:
Hide quick links:
Advertisement
Table of Contents
