If the plug provided is unsuitable for your socket outlets, the plug must be cut off and a suitable plug fitted. Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly.
Page 3
VENTILATION CAUTION When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 60 cm at top, 10 cm at rear, and 30 cm at each side). WARNING Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating.
Before you start Chapter 1: Before you start Checking what’s in the box Please check that you've received the following supplied accessories: • AM loop antenna • FM wire antenna • Dry cell batteries (AA size IEC R6) x2 • Remote control •...
5 minute guide Chapter 2: 5 minute guide Introduction to home theater You are probably used to using stereo equipment to listen to music, but may not be used to home theater systems that give you many more options (such as surround sound) when listening to soundtracks.
5 minute guide Listening to Surround Sound This receiver was designed with the easiest possible setup in mind, so with the following quick setup guide, you should have your system hooked up for surround sound in no time at all. In most cases, you can simply leave the receiver in the default settings.
5 minute guide Connect your speakers. A complete setup of speakers is shown here (six speakers for the VSX-415, and eight for the VSX- 515), but home setups may vary. Simply connect the speakers you have as shown below. receiver will work with just two stereo speakers (the front speakers in the diagram) but using at least three speakers is recommended, and a complete setup is best.
Page 10
5 minute guide Front speakers AUDIO FM UNBAL Ω DVR/ VIDEO TV / (TV/SAT) FRONT ASSIGNABLE COAX DIGITAL IN D V D 5.1CH INPUT (CD) CD-R / TAPE COAX / MD (DVD PLAY /LD) VSX-515 Powered subwoofer INPUT Plug in the receiver and switch it on, followed by your DVD player, subwoofer and TV. Make sure you’ve set the video input on your TV to this receiver.
5 minute guide Using the Quick Setup You can use the Quick Setup to get your system up and running with just a few button presses. The receiver automatically makes the necessary settings after you have selected your speaker setup, room size and listening position.
Page 12
5 minute guide • Check the table below to find the speaker setup that corresponds with your system. * VSX-515 model only Press ENTER . Use the MULTI JOG dial to choose your room size. Depending on the distance of your speakers from the listening position, choose between small, medium, or large (S, M or L), M being an average-sized room.
Quick surround sound setup Chapter 3: Quick surround sound setup VSX-515 model only Automatically setting up for surround sound (MCACC) The Auto Multi-Channel Acoustic Calibration (MCACC) setup measures the acoustic characteristics of your listening area, taking into account ambient noise, speaker size and distance, and tests for both channel delay and channel level.
Quick surround sound setup If you see an ERR message in the display, there may be a problem with your mic or the speaker connections. Turn off the power, and check the problem indicated by the ERR message (see below), then try the auto surround setup again. •...
Connecting up Chapter 4: Connecting up Making cable connections Make sure not to bend the cables over the top of this unit (as shown in the illustration). If this happens, the magnetic field produced by the transformers in this unit may cause a humming noise from the speakers.
Connecting up Connecting a DVD player and TV This page shows you how to connect your DVD player and TV to the receiver. Connect a coaxial digital audio output on your DVD player to the DIGITAL COAX 1 (DVD/LD) input on this receiver. Use a coaxial digital audio cable for the connection.
Connecting up Connecting the multichannel analog outputs For DVD Audio and SACD playback, your DVD player may have 5.1 channel analog outputs.In this case, you can connect them to the multi- channel inputs of the receiver as shown below. This receiver* AUDIO FM UNBAL Ω...
Connecting up Connecting other audio components The number and kind of connections depends on the kind of component you’re connecting. Follow the steps below to connect a CD-R, MD, DAT, tape recorder or other audio component. If your component has a digital output, connect this to a digital input on the receiver as shown.
Connecting up compatible player. However, the connected PC, DVD player, set-top box, etc. must be able to output WMA9 Pro format audio signals through a coaxial or optical digital output. ® Microsoft, Windows Media , and the Windows logo are trademarks, or registered trademarks of Microsoft Corporation in the United States and/ or other countries.
Connecting up Connecting antennas Connect the AM loop antenna and the FM wire antenna as shown below. To improve reception and sound quality, connect external antennas (see Using external antennas below). Always make sure that the receiver is switched off and unplugged from the wall outlet before making or changing any connections.
Connecting up Connecting the speakers (VSX-415) A complete setup of six speakers (including the subwoofer) is shown below, but everyone’s home setup will vary. Simply connect the speakers you have in the manner shown below. The receiver will work with just two stereo speakers (the front speakers in the diagram) but using at least three speakers is recommended, and a complete setup is best.
Connecting up Connecting the speakers (VSX-515) A complete setup of eight speakers (including the subwoofer) is shown below, but everyone’s home setup will vary. Simply connect the speakers you have in the manner shown below. The receiver will work with just two stereo speakers (the front speakers in the diagram) but using at least three speakers is recommended, and a complete setup is best for surround sound.
Connecting up Speaker terminals Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker terminal. If any of the bare speaker wire is touching the back panel when you switch the unit on, the power may cut off as a safety measure.
Page 24
Connecting up 3-D view of 7.1 channel speaker setup Overhead view of speaker setup Front Center left Surround left Listening position Surround back left Single surround back speaker Extra Power mode speaker setup VSX-415 only – see Using the Advanced surround effects on page 32 to switch on the Extra Power mode (EX POWER).
Controls and displays Chapter 5: Controls and displays Front panel ADVANCED ST/DIRECT SIGNAL STANDARD SURR /AUTO SURR SELECT LISTENING MODE VSX-515 model – STATION + – TUNING + VSX-415 model SPEAKER MODE SEARCH IMPEDANCE MULTI JOG TUNING CLASS /STATION VSX-515 model Input select buttons Press to select an input source.
Page 26
Controls and displays MCACC SETUP MIC jack Use to connect the supplied microphone (page 13). MASTER VOLUME 10 LISTENING MODE buttons STANDARD Press for Standard decoding and to switch between the various Pro Logic II and Neo:6 options (page 31). ADVANCED SURROUND Use to switch between the various surround modes (page 32).
Controls and displays Display VSX-515 model: VSX-415 model: SIGNAL SELECT indicators Lights to indicate the type of input signal: • AUTO – Lights when AUTO signal select is • SB – Depending on the source, this lights when a signal with surround back channel encoding is detected.
Page 28
Controls and displays VSX-515 model only – 2 PRO LOGIC II x lights to indicate Pro Logic IIx decoding (see Listening in surround sound on page 31 for more on this). VIR.SB Lights during Virtual surround back processing (page 37). DIRECT Lights when source direct playback is in use.
Controls and displays Remote control Illustration shows the VSX-515 remote control RECEIVER SLEEP FL DIMMER INPUT ATT INPUT SELECTOR DVD/LD DVD 5.1CH TV/SAT DVR/VCR CD-R/ TAPE/MD ADVANCED MIDNIGHT/ STANDARD SURROUND STEREO LOUDNESS TOP MENU MENU SYSTEM RETURN SETUP ENTER RECEIVER RECEIVER CONTROL VOLUME MUTE...
Page 30
Switch the display between station preset name and frequency (see tip on page 54). 12 DVD CONTROL buttons You can use these buttons to control a Pioneer DVD player connected to your system. Button What it does Turns DVD power on/off.
Listening to your system Chapter 6: Listening to your system Important • Certain features explained in this section will not be possible depending on the source (for example, PCM 88.2 / 96kHz, DTS 96kHz (24 bit) or WMA 9 Pro sources). Auto playback VSX-515 model only There are many ways to listen back to sources...
Listening to your system VSX-515 model only: • 2 Pro Logic IIx MOVIE – Up to 7.1 channel sound, especially suited to movie sources • 2 Pro Logic IIx MUSIC – Up to 7.1 channel sound, especially suited to music sources •...
Page 33
Listening to your system • EXPANDED – This mode is especially designed to give sound depth to stereo sources, and lets you hear two-channel (stereo) signals as simulated multichannel surround sound. Use with Dolby Pro Logic for a stereo surround effect. You can also use with Dolby Digital sources for a wider stereo field than the Standard modes.
Listening to your system Neo:6 Music settings VSX-515 model only • Default setting: 3 When listening to 2-channel sources in Neo:6 Music mode, you can adjust the center image to create a wider stereo effect with vocals. RECEIVER CONTROL VOLUME EFFECT/CH SEL LEVEL SIGNAL...
Listening to your system The MCACC indicator on the front panel lights when Acoustic Calibration EQ is active. Choosing the input signal • Default setting: AUTO You need to hook up a component to both analog and digital inputs on the rear of the receiver to select between input signals.
Listening to your system Using the surround back channel (Extended mode) VSX-515 model only • Default setting: EXT. ON You can have the receiver automatically use 6.1 decoding for 6.1 encoded sources (for example, Dolby Digital EX or DTS-ES), or you can choose to always use 6.1 decoding (for example, with 5.1 encoded material).
Listening to your system Using the Virtual Surround Back mode (VSB) Selecting this mode allows you to hear a virtual back channel through your surround speakers. For example, you can choose to listen to sources with no surround back channel infor- mation (for example, 5.1 encoded material) with emulated 6.1 encoding (VSB ON).
Listening to your system Using Midnight and Loudness listening The Midnight listening feature allows you to hear effective surround sound of movies at low volume levels. The effect automatically adjusts according to the volume at which you’re listening. The Loudness listening feature can be used to get good bass and treble from music sources at low volume levels.
Listening to your system Playing other sources RECEIVER SLEEP FL DIMMER INPUT ATT INPUT SELECTOR DVD/LD DVD 5.1CH TV/SAT DVR/VCR CD-R/ TAPE/MD ADVANCED MIDNIGHT/ Turn on the power of the playback component. Turn on the power of the receiver. Select the source you want to playback. Use the input select buttons (INPUT SELECTOR).
Setting up the receiver Chapter 7: Setting up the receiver VSX-415 model only Choosing your receiver setup For the best possible surround sound, complete the following set up operations. This is important when using DTS and Dolby surround. You only need to make the settings once (unless you change the placement of your current speaker system or add new speakers, etc.).
Setting up the receiver Surround and sound setup options Speaker setting • Default setting: S (all speakers) You must let the receiver know how many speakers you have, and how big they are. determines how much bass is sent from the receiver to the speakers.
Setting up the receiver Front speaker distance setting • Default setting: 3 m Sets the distance from the front speakers to the main listening position (within a range of 0.1 m to 9.0 m). • (cursor up/down) to set the distance of the front speakers.
Setting up the receiver Digital input settings Here you tell the receiver what components you have hooked up to the coaxial and optical DIGITAL IN jacks on the back of the receiver. After you assign a component to a digital jack, whenever you select that component, (for example, a DVD player) the receiver automatically changes to the digital input...
The System Setup menu Chapter 8: The System Setup menu VSX-515 model only Making receiver settings from the System Setup menu The following section shows you how to make detailed settings to specify how you’re using the receiver and also explains how to fine-tune individual speaker system settings to your liking.
The System Setup menu Select ‘M MCACC’ from the System Setup menu. See Making receiver settings from the System Setup menu above if you’re not already at this menu. Select the setting you want to adjust. If you’re doing this for the first time, you might want to make these settings in order.
The System Setup menu Fine Channel Distance • Default setting: 3 m (all channels) For proper sound depth and separation with your system, it is necessary to add a slight bit of delay to some speakers so that all sounds will arrive at the listening position at the same time.
Page 47
The System Setup menu • A. CH – All Channel Adjust is a ‘flat’ setting where all the speakers are set individually so no special weighting is given to any one channel. • F.ALG – Front Align Adjust balances the overall sound so that all speakers are set in accordance with the front speaker settings (no equalization is applied to the front left...
The System Setup menu • The OVER!! indicator shows in the display if the frequency adjustment is too drastic and might distort. If this happens, bring the level down until OVER!! disappears from the display. • Changing the frequency curve of one channel too drastically will affect the overall balance.
The System Setup menu Select SP SET from the SP SETUP menu. (cursor left/right) to choose the speaker(s) that you want to set then select a speaker size. (cursor up/down) to select the size (and number) of each of the following speakers: •...
The System Setup menu Select ‘ X.OVER’ from the SP SETUP menu. (cursor up/down) to choose the frequency cutoff point. Frequencies below the cutoff point will be sent to the subwoofer (or LARGE speakers). When you’re finished, press RETURN. Channel level Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor when setting up a...
The System Setup menu The Input Assign menu You only need to make this setting if you didn’t hook up your digital equipment according to the default settings for the digital inputs (see below). This setting tells the receiver what digital equipment is hooked up to which terminal so the buttons on the remote correspond to what you have hooked up.
The System Setup menu • MAX – Dynamic range is reduced (loud sounds are reduced in volume while quieter sounds are increased). When you're finished, press RETURN . Dual Mono Setup • Default setting: CH1 You can specify how dual mono encoded Dolby Digital soundtracks should be played.
Using the tuner Chapter 9: Using the tuner Listening to the radio The following steps show you how to tune in to FM and AM radio broadcasts using the automatic (search) and manual (step) tuning functions. Once you are tuned to a station you can memorize the frequency for recall later—...
Using the tuner RECEIVER SLEEP FL DIMMER INPUT ATT INPUT SELECTOR DVD/LD DVD 5.1CH TV/SAT DVR/VCR CD-R/ TAPE/MD ADVANCED MIDNIGHT/ STANDARD SURROUND STEREO LOUDNESS * Illustrations show the VSX-515 model Tune to a station you want to memorize. See Listening to the radio on page 53 for more on this.
Using the tuner An introduction to RDS Radio Data System (RDS) is a system used by most FM radio stations to provide listeners with various kinds of information—the name of the station and the kind of show they’re broadcasting, for example. One feature of RDS is that you can search by type of program.
Using the tuner If you want to keep listening to the station, press ENTER within the 5 seconds. If you don’t press ENTER, searching resumes. If NO PTY is displayed it means the tuner couldn’t find that program type at the time of the search.
Making recordings Chapter 10: Making recordings Making an audio or a video recording You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to the receiver (such as a CD player or TV). Keep in mind you can’t make a digital recording from an analog source or vice-versa, so make sure the components you are...
Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
Page 59
Additional information Problem Remedy Broadcast stations cannot be • Connect an outdoor antenna (refer to page 20). selected automatically. No sound from surround or • Connect the speakers properly. Refer to page 21 (VSX-415) or center speakers. page 22 (VSX-515). •...
Page 60
Additional information Problem When a search is performed by a DTS compatible CD player during playback, noise is output. Everything seems to be set up correctly, but the playback sound is odd. There seems to be a time lag between the speakers and the output of the subwoofer.
Additional information Resetting the main unit Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this. VSX-415 model: Switch the receiver into standby. While holding down the TONE button, press and hold the STANDBY/ON button for about three seconds.
Additional information Specifications Amplifier section • Continuous power output (stereo) Front: VSX-415 ..80 W (DIN 1kHz, THD 1.0%, 8 VSX-515 ..100 W (DIN 1kHz, THD 1.0%, 8 •...
A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest Pioneer authorized service center or your dealer for a replacement. Cleaning the unit •...
Page 64
Grazie per aver acquistato questo prodotto Pioneer. Leggere attentamente questo manuale di istruzioni per familiarizzarsi con l’uso dell’apparecchio. Conservare poi il manuale per ogni eventuale futuro riferimento.
Page 65
AVVERTENZA L’interruttore principale (STANDBY/ON) dell’apparecchio non stacca completamente il flusso di corrente elettrica dalla presa di corrente alternata di rete. Dal momento che il cavo di alimentazione costituisce l’unico dispositivo di distacco dell’apparecchio dalla sorgente di alimentazione, il cavo stesso deve essere staccato dalla presa di corrente alternata di rete per sospendere completamente qualsiasi flusso di corrente.
Page 66
01 Prima di cominciare Controllo dei contenuti della scatola ..6 Installazione delle batterie ....6 Gamma operativa del telecomando..6 Installazione del ricevitore.
Page 67
09 Come usare il sintonizzatore Ascolto della radio..... 53 Miglioramento del suono FM stereo ..53 Come salvare le stazioni di preselezione .
Capitolo 1: Prima di cominciare Controllo dei contenuti della scatola Controllare che siano stati inclusi i seguenti accessori in dotazione: • Antenna AM a telaio • Antenna FM a filo • Pile a secco (IEC R6, dimensione AA) x2 • Telecomando •...
Capitolo 2: Guida di 5 minuti Presentazione del sistema home theater Probabilmente conoscete già l’uso dei componenti stereo per ascoltare la musica, ma forse non avete ancora familiarizzato con i sistemi home theater che forniscono molte opzioni (ad esempio il suono surround) durante l’ascolto dei brani. Home theater riguarda l’uso di piste audio multiple per creare un effetto sonoro surround, per farvi sentire al centro dell’azione o di un concerto.
Ascolto del suono surround Questo ricevitore è stato disegnato con l’impostazione più facile in mente, quindi con questa guida rapida all’impostazione, il sistema sarà attivato per il suono surround praticamente subito. In molti casi, si può semplicemente lasciare inalterate le impostazioni standard del ricevitore. Assicurarsi di completare tutti i collegamenti prima di collegare quest’unità...
Page 71
Collegare gli altoparlanti. Qui viene mostrata una configurazione completa degli altoparlanti (sei altoparlanti per il VSX-415 e otto per il VSX-515), ma la configurazioni casalinghe possono variare. Collegare semplicemente gli altoparlanti come sotto mostrato. altoparlanti anteriori nel disegnno), ma raccomandiamo di usare almeno tre altoparlanti ed un’impostazione completa è...
Page 72
Altoparlanti anteriori Altoparlante centrale AUDIO FM UNBAL Ω LOOP ANTENNA DVR/ VIDEO T V / SA T ( T V / S A T ) MONITOR / LD FRONT ASSIGNABLE COAX DIGITAL IN D V D 5.1CH INPUT WOOFER (CD) CD-R PREOUT / TAPE...
Uso della Configurazione rapida È possibile usare la Configurazione rapida per fare funzionare rapidamente il sistema solo premendo qualche pulsante. Il ricevitore effettua le opportune impostazioni dopo aver selezionato la configurazione degli altoparlanti, la dimensione della stanza e la posizione di ascolto. •...
Page 74
• Controllare la tabella seguente per trovare la configurazione degli altoparlanti che corrisponde al sistema. Altoparlanti Altoparlante Altoparlanti anteriori centrale * Solo per il modello VSX-515 Premere ENTER. Usare il controllo MULTI JOG per scegliere la dimensione della stanza. A seconda della distanza degli altoparlanti dalla posizione di ascolto, scegliere tra piccola (S), media (M) o grande (L), M è...
Capitolo 3: Impostazione rapida suono surround Solo per il modello VSX-515 Impostazione automatica del suono surround (MCACC) L’impostazione del sistema automatico di calibratura acustica multicanale (MCACC) misura le caratteristiche acustiche dell’area di ascolto, prendendo in considerazione il rumore ambientale, la dimensione e la distanza degli altoparlanti e i test per il ritardo e il livello dei canali.
Se si vede un messaggio ERR sul display, può esservi un problema legato al microfono o ai collegamenti degli altoparlanti. Togliere l’alimentazione e controllare il problema indicato dal messaggio ERR (vedere sotto), quindi riprovare l’impostazione automatica del surround. • ERR MIC – Controllare la connessione del microfono.
Capitolo 4: Collegamento Come collegare i cavi Assicurarsi di non piegare i cavi sulla parte superiore di questa unità (come mostrato nell’illustrazione). Se ciò accade, il campo magnetico prodotto dai trasformatori in questa unità può provocare un ronzio dagli altoparlanti. Importante •...
Collegamento di un lettore DVD e di un televisore Questa pagina mostra come collegare il lettore DVD e il televisore al ricevitore. Collegare un’uscita audio digitale coassiale sul lettore DVD all’ingresso DIGITAL COAX 1 (DVD/LD) sul ricevitore. Usare un cavo audio digitale coassiale per il collegamento.
Collegamento delle uscite analogiche multicanale Per la riproduzione DVD Audio e SACD, il lettore DVD potrebbe avere uscite analogiche a 5.1 canali. In questo caso, è possibile collegarle agli ingressi multicanale del ricevitore, come sotto mostrato. CENTER OUTPUT WOOFER FRONT SURROUND OUTPUT OUTPUT...
Collegamento di altri componenti audio Il numero e il tipo di collegamenti dipende dal tipo di componente che si sta collegando. Seguire le fasi successive per collegare un CD-R, un MD, un DAT, una piastra a cassette o altri componenti audio. Se il componente ha un’uscita digitale, collegarlo ad un ingresso digitale sul ricevitore, come mostrato.
collegato, il lettore DVD, la set-top box, ecc. devono essere in grado di emettere segnali audio di formato WMA9 Pro attraverso un’uscita digitale coassiale o ottica. ® Microsoft, Windows Media e il logo Windows sono marchi commerciali o marchi commerciali registrati di Microsoft Corporation negli Stati Uniti e/o altri Paesi.
Collegamento delle antenne Collegare l’antenna AM a telaio e l’antenna FM a filo come segue. Per migliorare la ricezione e la qualità sonora, collegare le antenne esterne (vedi Uso delle antenne esterne qui sotto). Assicurarsi sempre che il ricevitore sia spento e scollegato dalla presa murale prima di effettuare o modificare i collegamenti.
Collegamento degli altoparlanti (VSX-415) Qui sotto è visualizzata un’impostazione completa di sei altoparlanti (compreso il subwoofer), ma l’impostazione privata può essere diversa. Collegare semplicemente gli altoparlanti nella maniera indicata. Il ricevitore funzionerà con solo due altoparlanti stereo (gli altoparlanti anteriori nel disegnno), ma raccomandiamo di usare almeno tre altoparlanti ed un’impostazione completa è...
Collegamento degli altoparlanti (VSX-515) Qui sotto è visualizzata un’impostazione completa di otto altoparlanti (compreso il subwoofer), ma l’impostazione privata può essere diversa. Collegare semplicemente gli altoparlanti nella maniera indicata. Il ricevitore funziona con appena due altoparlanti stereo (gli altoparlanti anteriori nell’illustrazione), ma si raccomanda l’uso di almeno tre altoparlanti ed un’impostazione completa è...
Terminali degli altoparlanti Assicurarsi che il filo nudo dell’altoparlante sia attorcigliato ed inserito completamente nel terminale dell’altoparlante. Se il filo nudo di un altoparlante tocca il pannello posteriore quando si accende l’unità, l’alimentazione potrebbe spegnersi come misura di protezione. Usare fili per altoparlanti di buona qualità...
Page 86
Vista 3-D dell’impostazione dell’altoparlante 7.1 canali Vista generale dell’impostazione dell’altoparlante Configurazione altoparlanti in modalità Extra Power Solo per il modello VSX-415 – vedere Uso degli effetti surround Advanced a pagina 32 per attivare la modalità Extra Power (EX POWER).
Capitolo 5: Controlli e display Pannello anteriore Tasti di selezione dell’ingresso Premere questo per selezionare una fonte d’ingresso. Display dei caratteri Vedi a Display a pagina 27. Indicatore MCACC S’illumina quando è attivata la funzione Acoustic Calibration EQ (pagina 34) (Acoustic Calibration EQ è...
Page 88
Presa MCACC SETUP MIC Usare questa per collegare il microfono in dotazione (pagina 13). MASTER VOLUME 10 Tasti LISTENING MODE STANDARD Premere questo tasto per una decodificazione standard e per commutare tra le varie opzioni Pro Logic II e Neo:6 (pagina 31).
Display Modello VSX-515: Modello VSX-415: Indicatori SIGNAL SELECT S’illumina per indicare il tipo di segnale in ingresso: • AUTO – S’illumina quando è attiva la selezione di segnale AUTO. • SB – A seconda della fonte, s’illumina quando viene rilevato un segnale con una codifica di canale posteriore surround.
Page 90
Solo per il modello VSX-515 – 2 PRO LOGIC II x s’illumina per indicare la decodifica Pro Logic IIx (vedere Ascolto con il suono surround a pagina 31 per ulteriori informazioni). VIR.SB S’illumina durante l’elaborazione posteriore surround virtuale (pagina 37). DIRECT S’illumina quando è...
Telecomando L’illustrazione mostra il telecomando del VSX-515 RECEIVER SLEEP FL DIMMER INPUT ATT INPUT SELECTOR DVD/LD DVD 5.1CH TV/SAT DVR/VCR CD-R/ TAPE/MD ADVANCED MIDNIGHT/ STANDARD SURROUND STEREO LOUDNESS TOP MENU MENU SYSTEM RETURN SETUP ENTER RECEIVER RECEIVER CONTROL VOLUME EFFECT/CH SEL LEVEL MUTE ACOUSTIC...
Page 92
Commutare il display tra il nome della stazione preselezionata e la frequenza (vedere suggerimento a pagina 54). 12 Tasti DVD CONTROL Si possono usare questi tasti per controllare un lettore DVD Pioneer collegato al sistema. Taste Funzione DVD Accende/spegne l’alimentazione del DVD.
Capitolo 6: Ascolto del sistema Importante • Alcune funzioni spiegate in questa sezione non saranno possibili a seconda della fonte (ad esempio, PCM 88,2 / 96kHz, DTS 96kHz (24 bit) o fonti WMA 9 Pro). Riproduzione automatica Solo per il modello VSX-515 Ci sono molte modalità...
Solo per il modello VSX-515: • 2 Pro Logic IIx MOVIE – Suono fino a 7.1 canali, particolarmente adatto per i film • 2 Pro Logic IIx MUSIC – Suono a 7.1 canali, particolarmente adatto per le fonti musicali • 2 Pro Logic IIx GAME – Suono a 7.1 canali, particolarmente adatto ai video giochi •...
Page 95
• EXPANDED – Questa modalità è stata disegnata specialmente per fornire profondità sonora alle fonti stereo e vi permette di sentire i segnali a due canali (stereo) come suono surround multicanale simulato. Da usare con Dolby Pro Logic per un effetto sonoro stereo. Potete anche usare questa modalità...
Impostazioni Neo:6 Music Solo per il modello VSX-515 • Impostazione standard: 3 Durante l’ascolto delle fonti a 2 canali nella modalità Neo:6 Music, è possibile regolare l’immagine centrale per creare un effetto stereo più ampio con le voci. RECEIVER CONTROL VOLUME EFFECT/CH SEL LEVEL...
L’indicatore MCACC s’illumina sul pannello anteriore quando è attivata la funzione Acoustic Calibration EQ. Come scegliere il segnale d’ingresso • Impostazione standard: AUTO E’ necessario collegare il componente agli ingressi analogico e digitale sul retro del ricevitore per selezionare tra i segnali d’ingresso. Modello VSX-515: ADVANCED ST/DIRECT...
Uso del canale posteriore surround (modalità Extended) Solo per il modello VSX-515 • Impostazione standard: EXT. ON Il ricevitore può essere impostato per usare automaticamente solo la decodifica 6.1 per le fonti con codifica 6.1 (per esempio, Dolby Digital EX o DTS-ES), o si può scegliere di usare sempre la decodifica 6.1 (ad esempio, con il materiale con codifica 5.1).
Uso della modalità Virtual Surround Back (VSB) La selezione di questa modalità permette di ascoltare un canale posteriore virtuale dagli altoparlanti surround. Ad esempio, potete scegliere di ascoltare le fonti senza informazioni sul canale posteriore surround (ad esempio materiali codificati a 5.1 canali) con la codificazione 6.1 emulata (VSB ON).
Uso delle modalità di ascolto Midnight e Loudness La funzione di ascolto Midnight vi consente di ascoltare il suono effettivo di film ad un basso livello di volume. L’effetto si regola automaticamente al volume d’ascolto. La funzione dell’ascolto Loudness può essere usata per ottenere degli ottimi bassi e acuti da fonti musicali ad un basso livello di volume.
Riproduzione di altre fonti RECEIVER SLEEP FL DIMMER INPUT ATT INPUT SELECTOR DVD/LD DVD 5.1CH TV/SAT DVR/VCR CD-R/ TAPE/MD ADVANCED MIDNIGHT/ Accendere la corrente del componente di riproduzione. Accendere la corrente del ricevitore. Selezionare la fonte da riprodurre. Usare i tasti di selezione di ingresso (INPUT SELECTOR).
Capitolo 7: Impostazione del ricevitore Solo per il modello VSX-415 Scelta dell’impostazione del ricevitore Per ottenere il migliore suono surround possibile, completare le seguenti operazioni di impostazione. Questo è importante quando si utilizza il surround DTS e Dolby surround. Queste impostazioni vanno fatte solo una volta (se non cambiate l’ubicazione dell’attuale sistema di altoparlanti o aggiungete nuovi altoparlanti, ecc.).
Opzioni di impostazione surround e del suono Impostazione degli altoparlanti • Impostazione standard: S (tutti gli altoparlanti) Occorre comunicare al ricevitore quanti altoparlanti vi sono e quanto sono grandi. determina la quantità di bassi inviata dal ricevitore agli altoparlanti. Usare / (cursore sù/giù) per scegliere •...
Impostazione della distanza dal altoparlante frontale • Impostazione standard: 3 m Imposta la distanza dagli altoparlanti frontali alla posizione di ascolto principale (nella gamma da 0,1 m a 9,0 m). Usare / (cursore sù/giù) per impostare • la distanza degli altoparlanti frontali. Impostazione della distanza dell’altoparlante centrale •...
Impostazioni dell’ingresso digitale Si “dice” al ricevitore quali componenti sono stati collegati alle prese coassiale e ottica DIGITAL IN sulla parte posteriore del ricevitore. Dopo aver assegnato un componente ad una presa digitale, quando si seleziona quel componente (ad esempio, un lettore DVD) il ricevitore passa automaticamente alle impostazioni dell’ingresso digitale e DIGITAL viene mostrato su display.
Capitolo 8: Menù System Setup Solo per il modello VSX-515 Come eseguire le impostazioni del ricevitore sul menù System Setup La seguente sezione mostra come effettuare impostazioni per specificare come si sta usando il ricevitore e spiega anche come effettuare una regolazione fine delle varie impostazioni del sistema degli altoparlanti a proprio piacimento.
Selezionare ‘M MCACC’ dal menù System Setup. Vedi a Come eseguire le impostazioni del ricevitore sul menù System Setup automatiche sopra se non è già visualizzato questo schermo. Selezionare l’impostazione da regolare. Se queste sono le prime impostazioni, bisogna eseguirle in ordine. •...
Distanza canale ottimo • Impostazione standard: 3 m (tutti i canali) Per una profondità e separazione corretta del sistema, è necessario aggiungere un certo ritardo ad alcuni degli altoparlanti in modo tale che tutti i suoni arrivino alla posizione d’ascolto allo stesso tempo. Le impostazioni seguenti possono aiutare ad effettuare regolazioni dettagliate che è...
Page 109
• A. CH – La regolazione All Channel Adjust (tutti i canali) è un’impostazione ‘piatta’, in cui tutti gli altoparlanti sono impostati individualmente. Quindi, nessun peso speciale viene dato ad un canale particolare. • F.ALG – La regolazione Front Align Adjust (Allineamento frontale) bilancia il suono complessivo in modo che tutti gli altoparlanti siano impostati secondo le...
• L’indicatore OVER!! appare sul display se la regolazione della frequenza è troppo improvvisa e si possono verificare distorsioni. In tal caso, abbassare il livello finché l’indicazione OVER!! non scomparirà dal display. Suggerimento • Il cambio della curva di frequenza di un canale in modo troppo repentino influisce sul bilanciamento generale.
Selezionare ‘SP SET.’ dal menu SP SETUP. Usare / (cursore sinistra/destra) per scegliere gli/l’altoparlante/i che si desidera impostare e quindi selezionare la dimensione degli altoparlanti. Usare / (cursore sù/giù) per selezionare le dimensioni (e il numero) di ognuno dei seguenti altoparlanti: •...
Al termine, premere RETURN. Livello del canale Usando le impostazioni del livello del canale, potete regolare il bilanciamento generale del sistema di altoparlanti e questo è molto importante nell’impostazione di un sistema home theater. Selezionare ‘CH LEVEL’ dal menù SP SETUP.
Menù Input Assign Occorre effettuare questa impostazione solo se non si sono collegati apparecchi digitali secondo le impostazioni predefinite per gli ingressi digitali (vedere sotto). Quest’impostazione informa il ricevitore del componente digitale collegato al terminale affinché i tasti del telecomando corrispondano al collegamento.
• MAX – La gamma dinamica è ridotta (i suoni forti hanno un volume ridotto, mentre i suoni silenziosi sono aumentati). Al termine, premere RETURN. Impostazione Dual Mono Impostazione standard: CH1 • E’ possibile specificare quante colonne sonore codificate dual mono Dolby Digital si possono riprodurre.
Capitolo 9: Come usare il sintonizzatore Ascolto della radio I seguenti punti mostrano come sintonizzare le trasmissioni radio FM e AM usando le funzioni di sintonizzazione automatica (ricerca) e manuale (punti). Dopo aver sintonizzato una stazione, è possibile memorizzare la frequenza per un richiamo successivo—vedere Come salvare le stazioni di preselezione a pagina 53 per ulteriori informazioni su come procedere.
RECEIVER SLEEP FL DIMMER INPUT ATT INPUT SELECTOR DVD/LD DVD 5.1CH TV/SAT DVR/VCR CD-R/ TAPE/MD ADVANCED MIDNIGHT/ STANDARD SURROUND STEREO LOUDNESS * L’illustrazione mostra il modello VSX-515 Sintonizzare la stazione da memorizzare. Vedi a Ascolto della radio a pagina 53 per ulteriori informazioni al riguardo.
Un’introduzione al sistema RDS Radio Data System (RDS) è un sistema usato da gran parte delle stazioni radio FM per fornire agli ascoltatori vari tipi di informazioni: ad esempio il nome della stazione e il tipo di spettacolo che stanno trasmettendo. Una funzione del RDS è...
Se desiderate continuare ad ascoltare la stazione, premere ENTER entro 5 secondi. Se non premete ENTER, la ricerca continua. Se l’indicazione NO PTY appare sul display, ciò significa che il sintonizzatore non è stato in grado di trovare il tipo del programma nel momento della ricerca.
Capitolo 10: Come fare le registrazioni Come fare una registrazione audio o video E’ possibile fare una registrazione audio o video dal sintonizzatore incorporato o da un’altra fonte audio o video collegata al ricevitore (ad esempio un lettore CD o un televisore).
Pioneer più vicino o al proprio concessionario di svolgere i lavori di riparazione. • Se l’unità non funziona in modo normale per via degli effetti esterni, quali l’elettricità statica, scollegare la spina d’alimentazione dalla presa murale e ricollegarla per ritornare alle normali...
Page 121
Problema Rimedio Non è possibile selezionare • Collegare un’antenna esterna (fare riferimento a pagina 20). automaticamente le stazioni di trasmissione. Assenza di suono dagli • Collegare correttamente gli altoparlanti. Fare riferimento alla altoparlanti surround o pagina 21 (VSX-415) o alla pagina 22 (VSX-515). centrali.
Page 122
Problema Quando viene effettuata una ricerca da un lettore CD DTS compatibile, viene emesso rumore. Tutto sembra impostato correttamente, ma il suono di riproduzione è strano. Sembra che ci sia una differenza di tempo tra gli altoparlanti e l’uscita del subwoofer.
Ripristino dell’unità principale Usare questa procedura per azzerare tutte le impostazioni del ricevitore ai valori di fabbrica. Usare i controlli sul pannello anteriore per effettuare questo. Modello VSX-415: Commutare il ricevitore nella modalità d’attesa. Mantenendo premuto il tasto TONE, premere e mantenere premuto il tasto STANDBY/ON per tre secondi circa.
Controllare il cavo d’alimentazione ogni tanto. Se è danneggiato, chiedere di sostituirlo al più vicino centro di servizio o concessionario autorizzato Pioneer. Pulizia dell'unità • Usare un panno di pulizia o un panno asciutto per rimuovere le tracce di polvere e sporcizia.
Page 126
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300 PIONEER ELECTRONICS DE MEXICO S.A. DE C.V. Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270 <05B00001>...