Owner Id - Panasonic NV-GS40 Operating Instructions Manual

N (F, E): Card Photoshot Picture Quality
(during Card Photoshot
recording)
[F] means Fine, [N] means
Normal and [E] means Economy.
-39-
, , : MPEG4 Picture Quality
N F SF
ACCESS: While Card is being read (during
Playback, Formatting and
Multi-Picture Function use).
0: Remaining Number of Card
Photoshot pictures
R:0h00m: Remaining time of MPEG4 or
Voice data
H, L: Card Continuous Photoshot
Recording
: Lock Setting
¥ (White):
DPOF Setting completed (set to
1 or more picture)
¥ (Green):
Slide Show Settings completed
-44-
¥ (Blue):
DPOF Setting (set to 1 or more
picture)/Slide Show Settings both
completed
: [640k480] Image size
640
≥For images not recorded with this Movie
Camera, the size display is determined as
follows according to the number of horizontal
pixels.
: 640 or more, less than 800 (The
640
size is not displayed at under
640 pixels.)
: 800 or more, less than 1024
SVGA
: 1024 or more, less than 1280
XGA
: 1280 or more, less than 1600
SXGA
: 1600 or more, less than 2048
UXGA
: 2048 or more
QXGA
(Cyan): Card Photoshot Mode
PICTURE
(Red): While Card Photoshot recording
PICTURE
is activated
(Red): No Card (Still Picture Mode)
PICTURE
(Cyan): Moving Picture (MPEG4)
MPEG4
Recording
(Red): While Moving Picture (MPEG4)
MPEG4
recording is activated
(Red): No Card (MPEG4 Mode)
MPEG4
(Cyan): Voice Recording Mode
VOICE
(Red): While Voice Recording is
VOICE
activated
(Red): No Card (Voice Recording Mode)
VOICE
ª To Change the Counter Display Mode
By changing [C.DISPLAY] on the
[DISPLAY SETUP] Sub-Menu, you can change
the Counter Display Mode to Tape Counter
Indication [COUNTER] (0:00.00), Memory
Counter Indication [MEMORY] (M0:00.00), and
Time Code Indication [TIMECODE]
Others
-41-
-38-
-39-
-39-
-47-
-46-
,
-44- -46-
(0h00m00s00f). (
-15-
[COUNTER] Button on the Remote Controller,
you can change the Counter Display Mode.
ª To Display Date/Time Indication
To display Date/Time Indication, set the
appropriate Date/Time in [DATE/TIME] on the
[DISPLAY SETUP] Sub-Menu. (
You can also press the [DATE/TIME] Button of
the Remote Controller repeatedly to display or
change the Date/Time Indication.
ª To Change the Display Mode
By changing [DISPLAY] on the
[DISPLAY SETUP] Sub-Menu, you can change
the Display Mode to All Function Display [ALL],
Partial Display [PARTIAL] and Minimum Display
[OFF]. ( )
-15-

Owner ID

You can register your name and address in your
Movie Camera to identify the owner.
1
Set [CAMERA FUNCTIONS] >>
[OTHER FUNCTIONS1] >> [OWNER ID SET]
>> [YES].
≥The [OWNER ID] Menu appears.
2
Turn the [PUSH] Dial
[PIN NUMBER] and press the [PUSH] Dial
(38) to input desired numbers.
3
Turn the [PUSH] Dial
and press the [PUSH] Dial
them.
≥Be sure to input 4 digits. Otherwise the Pin
Number will not be registered.
4
Press the [∫] Button.
5
Repeat Steps 2–4 to input desired
characters for [NAME] and [POSTCODE].
≥You can input up to 12 characters in [NAME],
and up to 11 characters in [POSTCODE].
6
Press the [∫] Button to finish the setup.
To Verify Owner ID
Keep pressing the [;] Button for approximately
5 seconds.
To Correct the Contents
If Owner ID has already been set, carrying out
Step 1 will display [INPUT PIN NUMBER] on the
screen. Input the Pin Number you have already
selected. If the number is not correct, the screen
will not change. If the number is correct, the
contents of the setup will be displayed. (By
repeating Steps 2 to 4, you can change the
contents.)
-52-
) By repeatedly pressing the
)
-15-
(38) to select
(38) to select numbers
(38)
to enter