Owner Id; Initializing The Modes; Warning/Alarm Indications - Panasonic NV-GS30EN Operating Instructions Manual

ª To Display Date/Time Indication
To display Date/Time Indication, set the
appropriate Date/Time in [DATE/TIME] on the
[DISPLAY SETUP] Sub-Menu. (
You can also press the [DATE/TIME] Button of
the Remote Controller repeatedly to display or
change the Date/Time Indication.
ª To Change the Display Mode
By changing [DISPLAY] on the
[DISPLAY SETUP] Sub-Menu, you can change
the Display Mode to All Function Display [ALL],
Partial Display [PARTIAL] and Minimum Display
-56-
[OFF]. ( )

Owner ID

You can register your name and address in your
Movie Camera to identify the owner.
1
Set [CAMERA FUNCTIONS] >>
[OTHER FUNCTIONS1] >> [OWNER ID SET]
>> [YES].
≥The [OWNER ID] Menu appears.
2
Turn the [PUSH] Dial
[PIN NUMBER] and press the [PUSH] Dial
(32)
to input desired numbers.
3
Turn the [PUSH] Dial
and press the [PUSH] Dial
them.
≥Be sure to input 4 digits. Otherwise the Pin
Number will not be registered.
4
Press the [∫] Button.
5
Repeat Steps 2–4 to input desired
characters for [NAME] and [POSTCODE].
≥You can input up to 12 characters in [NAME],
and up to 11 characters in [POSTCODE].
6
Press the [∫] Button to finish the setup.
To Verify Owner ID
Keep pressing the [;] Button for approximately
5 seconds.
To Correct the Contents
If Owner ID has already been set, carrying out
Step 1 will display [INPUT PIN NUMBER] on the
screen. Input the Pin Number you have already
selected. If the number is not correct, the screen
will not change. If the number is correct, the
contents of the setup will be displayed. (By
repeating Steps 2 to 4, you can change the
contents.)

Initializing the Modes

You can change the Menu settings back to the
shipping condition.
-56-
)
(32) to select
(32) to select numbers
(32) to enter
Others
1
Set [CAMERA FUNCTIONS] >>
[OTHER FUNCTIONS2] >> [INITIAL SET] >>
[YES].
≥The initializing takes for a while.
≥After the initializing is completed, the
[COMPLETED] Indication appears with
beeps.
≥Initializing will not erase the Owner ID setting
and the clock setting (
adjusted.

Warning/Alarm Indications

If any one of the following indications lights up or
flashes, please check the condition of the Movie
Camera.
3: Condensation has occurred.
Y: The accidental erasure prevention slider on
the inserted Cassette is open (that is, set to
[SAVE]).
You are about to do audio dubbing on the
unrecorded (blank) portion of the tape.
No Cassette is inserted.
6: The Battery is low. Recharge it.
0: The built-in battery is low.
::
The video heads are dirty.
2END:
The tape came to end during recording.
REMOTE:
Wrong Remote Controller Mode has been
-51-
selected.
UNPLAYABLE TAPE
(OTHER FORMAT):
You are attempting to play back a tape
section that has been recorded with a
different TV system.
UNABLE TO A. DUB
(LP RECORDED):
Because the original recording was done in
LP Mode, audio dubbing cannot be
performed.
INCOMPATIBLE TAPE:
This Cassette is incompatible.
PLEASE RE-OPERATE
AFTER PUSHING
RESET BUTTON:
Mechanism Irregular is detected. Press the
[RESET] Button (
problem.
TO SERVICE:
It is a malfunction.
COPY INHIBITED:
Because the medium is protected by a copy
guard, images cannot be recorded
correctly.
-81-
-57-
) that has been
-87-
-53-
-51-
-58-
-87-
-48-
). This may solve the