Setting The Channels And Clock - Panasonic Diga DMR-EX99VEB Operating Instructions Manual

Setting the Channels and Clock

Preparation:
≥ Turn on the mains for the television
(and connected equipment) and select
the appropriate AV input to suit the
connections to this unit.
≥ These are the first settings you make
upon buying the unit. You don't need to
make these settings again.
1

to turn the unit on.
DVB Auto Setup starts. The unit will
search for the digital terrestrial
channels. This takes about
5 minutes.
Power Save in Standby
2
Function:
3, 4
to select "On", "On
Timer" or "Off" then
"On": It will go into the Power Save in Standby mode
when the unit is in standby mode.
"On Timer": Press [3, 4, 2, 1] to set the start and stop time
and then press [OK].
≥"Power Save in Standby" is set to activate during
the setting time period.
"Off": It is possible to start quickly from the standby
mode. (Quick Start mode)
The features of the Power Save in Standby function when the
unit is in standby mode are as below.
Power Save in Standby
Power consumption
Quick Start* 1
Front display
Watching the picture from the digital
satellite receiver connected to the
AV2 terminal
The unit could take over 1 minute to switch ON from standby mode with
§1
Quick start deactivated.
This time could be reduced to less than 10 seconds with Quick start
activated.
When "RF OUT ( Aerial Signal )" is set to "Off" in the Setup menu (
§2
When setup has completed, the confirmation screen appears.
3
OK
TV's remote
control
DVB Auto Setup
Scan CH 21
CH Channel Name
27 BBC ONE Wales
27 BBC 2W
27
BBC NEWS 24
27
BBC Radio Wales
TV: 6 Radio: 4
Searching...
RETURN
Power Save in Standby
Power Save
From
0 :00
OK
Saves standby power consumption
by disabling Quick Start function and
CHANGE
AV2 loop-through in standby.
OK
RETURN
Activated Deactivated
(On/On Timer)
2
Approx. 0.5W * Approx. 16W
Deactivated
Turns off
(The clock display
disappears.)
Cannot do
(continued on the next page)

DRIVE
SELECT
1
4
68
7
Type Quality
TV 9
TV 9
TV
9 DELETE
Radio 9
Data: 0
RESET
SKIP/INDEX
STOP
STATUS
On
To
6 :00
OPTION
REC
TEXT
Tips
To cancel Auto-Setup
Press [RETURN
(Off)
If the unit displays "No stations found!"
Press [1] to select "No" and press [OK]. Go
Activated
to step 2. After you have performed steps
2–;, turn off the unit and confirm the cable
or aerial input is connected to the RF IN
Stays lit
terminal. Restart the Auto-Setup again
( 79, DVB Auto Setup by Signal Quality).
If the clock setting menu appears or the
Can do
clock is not correct
Set the clock manually (
Restarting the Auto-Setup (
Auto Setup by Signal Quality )
To set the channel list best suited to your
84)
region (
Region)
About the screen saver function
When this unit is not operated for
approximately 5 minutes while the screen is
being displayed, the screen saver may be
displayed.
You can turn this function off (
Saver).
TV

VOL
CH
AV
TRACKING/V-LOCK/PAGE
3
2
CH
5 6
PROG/CHECK
8 9
CHAPTER
0
INPUT
SELECT
SLOW/SEARCH
REW FF
PAUSE PLAY
EXIT
PAUSE LIVE TV
OK
RETURN
MANUAL SKIP
-10s +60s
REC MODE EXT LINK DIRECT TV REC
TIME SLIP
STTL DISPLAY
JET REW
].
14).
79, DVB
79, DVB Auto Setup by
81, Screen
13
VQT2J45