Messages; On The Unit's Display - Panasonic Diga DMR-EX99VEB Operating Instructions Manual

Messages

On the Unit's Display

H∑∑, F∑∑
("∑" stands for a service number.)
DVD
("∑" stands for a number.)
GUIDE
HARD ERR
§
NoCASSETTE
§
NoERAS
NoREAD
NoWRIT
FINAL
PLEASE WAIT
§
PROG FULL
§
PROTECT
§
REMOVE
SW-DL
SP 35:50, LP 151h
"SP", "LP" and the numbers are examples.
UNSUPPORT
§
UNFORMAT
§
EXT-L
F74
F75
U59
U61
U76
U80, U81, U99
The message are alternately displayed.
§
92
VQT2J45
≥ An error has occurred. The number following "H" or "F" depends on the status of the
unit. Check the items below and in the Troubleshooting Guide. If the service number still
does not disappear after the check, reset the unit (
≥ If the service numbers fail to clear, note the service numbers and contact a qualified
service person.
≥ The remote control and the main unit are using different codes. Change the code on the
remote control. ( 94)
≥ GUIDE Plus+ data is being downloaded. (
≥ If there is no change after turning the unit on and off, consult the dealer where the unit
was purchased.
≥ You have not inserted a video cassette for the recording. (
≥ You cannot delete items on this disc.
≥ The disc may be damaged. Use a new disc.
≥ The disc is dirty or badly scratched. The unit cannot record, play, or edit. (
≥ The disc may be incompatible or of poor quality. (
≥ You have used a lens cleaner and it has finished operation. Press [< OPEN/CLOSE] on
the main unit to eject the disc. (
≥ You cannot write to this disc.
The disc may be damaged. Use a new disc.
≥ When the screen asking if you want to finalise the disc appears, the message is displayed. ( 28)
≥ Displayed when the unit is started. This is not a malfunction.
≥ The unit is carrying out its recovery process. You cannot operate the unit while the
message is displayed.
≥ There are already 32 timer recording programmes. Delete unnecessary timer recording
programmes. ( 33)
≥ You have inserted a video cassette without the accidental erasure prevention tab. Use a
video cassette with an accidental erasure prevention tab. (
≥ The USB device is drawing too much power. Remove the USB device and turn the unit off.
≥ The unit is performing a software update. (
≥ Available space on the HDD or disc.
The example "SP 35:50" is displayed when less than 100 hours are available and the
example "LP 151h" is displayed when over 100 hours are available.
"SP" and "LP" are recording modes, "35:50" means "35 hours 50 minutes" and "151h"
means "151 hours".
≥ You have inserted a disc the unit cannot play or record onto. (
≥ You tried to operate with a non-compatible USB memory. (
≥ You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or DVD-
RW (DVD-Video format) that has been recorded on other equipment.
Format the disc to use it.
However all the recorded contents on the disc are deleted. (
≥ This unit is in EXT LINK standby. EXT LINK has been turned on and will stop operation
on the unit until the recording has completed.
Press [EXT LINK] to stop recording or cancel linked timer. (
≥ The HDMI connection could not be authenticated due to a transfer malfunction. If you
have another HDMI cable, try to use it. If it remains displayed, consult the dealer where
the unit was purchased.
≥ The HDMI connection could not be authenticated due to an internal data malfunction. If
you have another HDMI cable, try to use it. If it remains displayed, consult the dealer
where the unit was purchased.
≥ The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling
fan on the rear of the unit.
≥ (When a disc is not inserted) Displays when a malfunction has occurred. This is
displayed when the unit is in the recovery process to return to normal operation. Once
the display disappears you can use the unit again.
If it remains displayed, consult the dealer where the unit was purchased.
≥ HDMI cannot be output because this unit is connected to a model that does not support
copyright protection.
≥ The unit fails to operate properly. Press [Í/I] on the main unit to switch the unit to
standby mode. Press [Í/I] on the main unit again to turn the unit on.
94, To restore the unit if it freezes).
84)
89)
15, 16)
7)
89)
84)
15, 16)
17)
28)
30)
89)