Parameter Summary - YOKOGAWA EJX Series User Manual

8. Parameter Summary
NOTE
For HART protocol revision 7, F
and PROFIBUS PA communication types, and
EJX910A/EJX930A, please refer to manuals in the
attached CD-ROM.
 Menu Tree for HART Protocol Revision 5 (Except EJX910A and EJX930A)
(Device setup)
1 Process variables
2 Diag/Service
3 Basic setup
Online Menu
1 Device setup
2 Pres
3 AO
4 LRV
5 URV
4 Detailed setup
5. Review
Hot Key
1 Keypad Input 1 LRV
2 URV
3 Unit
4 LSL
5 USL
6 Min Span
1 Write protect
2 Enable wrt 10min
2 Wrt protect menu
3 New password
4 Software seal
Fieldbus
OUNDATION
(Process variables)
1 Pres
2 Pres %
3 AO
4 SP
5 SP %
6 Snsr temp
7 Engr Disp
8 Engr exp
9 Engr Unit
(Basic setup)
1 Tag
2 Unit
1 Keypad input
2 Apply values
3 Re-range
1 Date
4 Device information
2 Descriptor
3 Message
4 Write Protect
1 Linear
2 Sq root
5 Xfer fnctn
6 Pres Damp
7 Low cut
Linear
Zero
8 Low cut mode
Normal
9 H/L Swap
Reverse
SP setup
(Detailed setup)
1 Pressure sensor
1 Sensors
2 SP sensor
3 Temp sensor
1 Snsr temp
2 Amp temp
3 Temp Unit
1 Process variables
2 Signal condition
2 Re-range
3 Unit
4 Xfer fnctn
5 Pres Damp
6 Low cut
7 Low cut mode
8 H/L Swap
9 Bi-dir mode
Quick resp
T.Z. Cmp menu
S.C. menu
1 S.C.
2 Num of points
3 Point setting
1 Process variables
3 Output condition
2 Analog output
3 HART output
4 Process Alerts
1 Disp select
4 Display condition
2 P disp condition
3 SP disp condition
4 Engr disp range
5 Bar Indicator
1 Field device info
5 Device information
2 Sensor information
3 Self test
6 Test Key
<8. Parameter Summary>
IMPORTANT
If the transmitter is turned off within 30 seconds after
parameters have been set, the set data will not be
stored and the terminal returns to previous settings.
(Diag/Service)
1 Test device 1 Status
2 Self test
2 Loop test
1 Re-range
3 Calibration
2 Analog output trim
3 Pres sensor trim
4 SP sensor trim
5 Trim info.
4 Diag Parameters See A
(next page).
1 Error log view
5 Error log
2 Error log Clear
1 Pres 1 Pres Zero trim
2 Pres % 2 Pres trim
3 P LTP
3 Unit
4 P UTP
4 Pres sensor trim
5 Pres trim info.
1 SP
2 SP %
3 SP Unit 1 Static Pres trim
2 SP LTP
4 A/G Select
3 SP UTP
5 SP H/L Select
4 SP trim info.
6 SP sensor trim
7 SP setup 1 SP range
2 SP Unit
1 Pres
3 SP Damp
2 Pres %
4 SP A/G Setup
3 SP
5 SP H/L Select
4 Snsr temp
1 Keypad input
2 Apply values
1 T.Z. Cmp mode
2 Temp Zero
1 Pres
2 Pres %
3 AO
4 SP
5 SP %
1 Loop test
6 Snsr temp
2 D/A trim
7 Engr Disp
3 Scaled D/A trim
8 Engr exp
4 Clear D/A trim
9 Engr Unit
5 AO alm typ
Digital Output
6 Auto recover
7 AO lower limit
8 AO upper limit
1 Poll addr
1 Pres Alert mode
2 Num req preams
2 Config Pres Alerts
3 Burst mode
3 SP Alart mode
4 Burst option
4 Config SP Alerts
5 Temp Alert mode
6 Config Temp Alerts
1 Disp Out 1 7 DO Config
2 Disp Out 2
3 Disp Out 3
4 Disp Out 4
1 Disp Pres % fnctn
1 Tag
2 Disp Pres % Reso
2 Date
3 Pres disp point
3 Descriptor
1 Engr LRV
4 Message
2 Engr URV
5 Model 1
3 Engr exp
6 Model 2
4 Engr Unit
7 Model 3
5 Engr point
8 Write Protect
6 Set Engr Unit
9 Ext SW
7 Modify Engr Unit
Revision #s
Additional Info
40
1 Status group 1
2 Status group 2
3 Status group 3
4 Status group 4
5 Status group 5
6 Status group 6
7 Status group 7
8 Status group 8
9 Status group 9
1 Keypad input
2 Apply values
1 D/A trim
2 Scaled D/A trim
3 Clear D/A trim
1 Pres Zero trim
2 Pres trim
3 P LTP
4 P UTP
5 Pres trim info.
1 Static Pres trim
2 SP LTP
3 SP UTP
4 SP trim info.
1 Trim Who
2 Trim Date
3 Trim Loc
4 Trim Desc
1 P LTD
2 P UTD
3 Clear P snsr trim
1 SP LTD
2 SP UTD
3 Clear SP snsr trim
1 Digital Output
2 DO Select
3 DO Signal type
4 DO Test
1 Universal rev
2 Fld dev rev
3 Software rev
F0801-1.ai
IM 01C25A01-01E