Page 2
An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written per-mission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”).
CONTENTS GENERAL VIEW ..................v COMPLIANCE..................... vi FCC Compliance...................vi Laser Safety....................vii WEEE Compliance ..................xi Power Supply....................xi PATENTS ....................xi SERVICES AND SUPPORT............... xii INTRODUCTION ..................1 Lynx™ D Description ..................1 Package Contents..................2 Configuration Methods .................. 2 USING LYNX™ D..................3 Aiming System ....................
Page 4
TEST CODE SYMBOLS................48 MAINTENANCE ..................49 TECHNICAL FEATURES ................50 CODE IDENTIFIER TABLE................ 54 HEX AND NUMERIC TABLE ..............56...
FCC COMPLIANCE Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference which may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Page 8
Aiming System The Lynx™ D aiming system meets the requirements for laser safety. CAUTION-CLASS 2 LASER LIGHT WHEN OPEN DO NOT STARE INTO BEAM LASER LIGHT - DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT MAX. OUTPUT RADIATION 0.25 mW - EMITTED WAVELENGTH 640~660 nm TO EN 60825-1:2001 LASERSTRAHLUNG –...
Page 9
The product utilizes a low-power laser diode. Although staring directly at the laser beam momentarily causes no known biological damage, avoid staring at the beam as one would with any very strong light source, such as the sun. Avoid that the laser beam hits the eye of an observer, even through reflective surfaces such as mirrors, etc.
Page 10
Laserstrahl zu schauen, genauso wenig wie in starke Lichtquellen (z.B. die Sonne). Vermeiden Sie es, den Laserstrahl weder gegen die Augen eines Beobachters, noch gegen reflektierende Oberflächen zu richten. FRANÇAIS Les informations suivantes sont fournies selon les règles fixées par les autorités internationales et se réfèrent à...
The LYNX™ D Hand-Held Reader is not user-serviceable. Opening the case of the unit can cause internal damage and will void the warranty. CAUTION WEEE COMPLIANCE POWER SUPPLY This device is intended to be supplied by a UL Listed or CSA Certified Power Unit marked "Class 2"...
SERVICES AND SUPPORT Datalogic provides several services as well as technical support through its website. Log on to www.scanning.datalogic.com and click on the links indicated for further information including: • PRODUCTS Search through the links to arrive at your product page where you can download specific Manuals and Software &...
INTRODUCTION INTRODUCTION LYNX™ D DESCRIPTION The Lynx™ D Hand-Held Reader packs a lot of performance into an attractive, rugged, hand-held device. It operates in commercial and industrial environments as well as the front office. To read a symbol or capture an image, you simply aim the Omni-directional reader and pull the trigger.
LYNX™ D PACKAGE CONTENTS The following parts are included in the Lynx™ D package contents: • Lynx™ D Hand-Held Reader • CD-ROM containing the Lynx™ D Configuration Tools software and Lynx™ D Reference Manual • Lynx™ D User’s Manual You may want to save your packing material in case you need to ship the reader at some later time.
USING LYNX™ D USING LYNX™ D AIMING SYSTEM The Lynx™ D reader uses an intelligent aiming system similar to those on cameras. By partially pulling the trigger, the aiming system indicates a field of view to be positioned over the code: Figure 1 - Aiming System When you pull the trigger completely a red beam illuminates the code.
LYNX™ D The field of view indicated by the aiming system will be smaller when the Lynx™ D is closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit. Symbologies with larger bars or elements (mil size) should be read farther from the unit.
INITIAL SETUP INITIAL SETUP This procedure allows setting up the reader to operate with the default settings: Whenever you need to change the default values refer to chapter 4. RS232 INTERFACE SELECTION The Lynx™ D reader requires the RS232 interface cable and the AC/DC power adapter to be connected.
LYNX™ D WEDGE INTERFACE SELECTION The Lynx™ D reader requires the Wedge interface cable and the AC/DC power adapter to be connected. To install and configure your reader with the Wedge interface, follow these instructions: Make all the Lynx™ D reader connections as shown in Figure 4: Figure 4 –...
INITIAL SETUP When not using the Lynx™ D reader remember to disconnect the Wedge interface from the PC before disconnecting the power cord. CAUTION While using the Lynx™ D it is always necessary to use cables adopting an external power supply. NOTE USB INTERFACE SELECTION The Lynx™...
Page 20
For USB COM the relevant files and drivers must be installed from the USB Device Installation software which can be downloaded from the web page http://www.scanning.datalogic.com. • For USB Keyboard and for USB Generic HID the correct USB driver is included in the Host Operating System and will either be loaded automatically or will be suggested by the O.S.
Page 21
INITIAL SETUP The Lynx™ D reader is a USB self-powered device. NOTE If you need to change the USB device interface, after having reconfigured the reader, you have to disconnect and reconnect the cable to the PC. NOTE...
LYNX™ D CONFIGURATION USING CODE SYMBOLS This section describes the programming method of using configuration code symbols to program your reader. By using the Lynx™ D reader to read/decode these special configuration symbols, you can configure, and obtain information from its system software.
CONFIGURATION USING CODE SYMBOLS DEFAULT SETTINGS The following table lists the default values of all configurable parameters. The parameters preceded by the ( ) symbol may be configured in this manual. For a complete configuration of all parameters refer to the Lynx™ D Reference Manual available on the CD-ROM.
Page 24
LYNX™ D Configuration Field Default Setting Data Format-Symbology Indep. Pars. (continued) *Header No headers *Terminator CR and LF terminators for RS232, USB BULK, USB COM, USB Generic HID ENTER terminator for Wedge, USB Keyboard Data Format-Symbology Dependent Parameters Symbology Specific Format Select All Header Symbology No headers...
Page 25
CONFIGURATION USING CODE SYMBOLS Configuration Field Default Setting Code 39 (continued) Minimum Length Maximum Length Start/Stop Character Disabled Code 32 Selection Disabled Interleaved 2 of 5 Selection Enabled - check digit control and tx Code Length Check Disabled Minimum Length Maximum Length Codabar Selection...
Page 26
LYNX™ D Configuration Field Default Setting Data Matrix Selection Enabled - normal & inverted Rectangular Style Enabled Minimum Code Length 0001 Maximum Code Length 3600 Selection Enabled Postal Codes Selection Disabled Maxicode Maxicode Mode 1 Disabled Maxicode Mode 2 Disabled Maxicode Mode 3 Disabled Maxicode Mode 4...
Page 27
CONFIGURATION USING CODE SYMBOLS Configuration Field Default Setting Image Formatting Image Preset 1, 2, 3, 4 Image Format JPEG format Resolution Full (640x480) Set JPEG Quality Factor Window Origin (0,0) Window Dimensions (640x480) Brightness Contrast Zoom 100% Color Depth 256 gray levels...
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL NTERCODE ELAY Intercode Delay AOALBPFOHNGNENEIEPANHOGOCK = disabled AHPNIJAMDKEOFMHMLJALFEHEIK AKCBPJCJGIIJCMCEHOLJCCLLPK 01-99 = delay from 1 to 99 sec AEFBJLBGMHPKMKHHHMDHGNPHGK AAPHBAJIDAHFGABNDAIPBNELBK AELFANMJEEGKOPKMLLMCEOMLLK...
Page 33
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL EYBOARD ATIONALITY This parameter default value is restored through the Interface Selection code and not Restore Default. Belgian English AOAPCOGMHNGNENEIEPANHOGOCK...
Page 34
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL EYBOARD PEED This parameter default value is restored through the Interface Selection code and not Restore Default. Normal Fast AOAPBPGMFNGNENEIEPANHOGOCK...
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL WEDGE INTERFACE Caps Lock Off Caps Lock On AOCOCOFOHNGNENEIEPANHOGOCK AOCOCOFOHNGNENEIEPANHOGOCK AHHPMJAMDKEOFMHMLJAKEEHFIK AHHPMBIMDKEOFMHMLJAKECFGIK AKCBPJCJGIIJCMCFHPJMFONJPK AKCBPJCJGIIJCMCFGOKAPBGHJK AEFBJLBGMHPKMPEAEFKPFEBEGK AEFBJLBGMHPKMIDELANDPCKFGK AAPHBAJJDDHLCANDMPHCNCFDHK AAPHBAJJCADMHJHMCCDOLKDBBK AFLFALKFFFDCEGMMLKJKOLEKJK AELFAOLMJDAEOMIJBPOGGCDLLK...
Page 36
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL EYBOARD ATIONALITY This parameter default value is restored through the Interface Selection code and not Restore Default. Belgian English AOCOCOGMHNGNENEIEPANHOGOCK...
Page 37
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL EYBOARD ETTING The values set by this procedure are not effected by the Restore Default code but will be lost if the Interface Selection code is read.
Page 38
CONFIGURATION Some ASCII characters may be missing as this depends on the type of keyboard: these are generally particular characters relative to the various national symbologies. In this case: • The first 4 characters (Shift, Alt, Ctrl, and Backspace) can only be substituted with keys not used, or substituted with each other.
Page 39
CONFIGURATION Acoustic Signals Four types of acoustic signals are associated with the following steps: Enter keyboard setup Exit keyboard setup SHIFT, ALT, CTRL, BACKSPACE keys Keyboard keys (SHIFT, ALT, CTRL, BACKSPACE excluded) These signals facilitate the selection of those characters requiring more than one key pressed simultaneously.
Page 40
CONFIGURATION XTENDED EADER ERMINATOR For the WEDGE interface, the following extended keyboard values can also be configured: These values are restored through the Interface Selection code and not Restore Default. EXTENDED KEYBOARD TO HEX CONVERSION IBM AT ENTER HOME PG UP PG DOWN ↑...
Page 41
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL USTOM XTENDED EADER ERMINATOR Set Extended Keys AOCOBLHMFNGNENEIEPANHOGOCK AHPNIJAMDKEOFMHMLJAKFAHEIK AKCBPJCJGIIJCMCEGJMDPHOPJK AEFBJLBGMHPKNMHNBGHNEDDEGK AAPHBAJJCBCBJNFHFHFBFPJNHK AFLFAOPHBFNMIOAIIIOEMAEJLK DLLLLLLDDDLLLLLDLDDDDLDLLL The extended Header/Terminator keys for Wedge Interface users can be customized by defining them through a simple keyboard setting procedure.
Page 42
CONFIGURATION If the first 4 KEYS (Shift, Alt, Ctrl, and Backspace) are not available on your keyboard, you can only substitute them with keys not used, or substitute them with each other. The reader signals the end of the procedure with 3 beeps indicating the keys have been registered.
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL Acoustic Signals Four types of acoustic signals are associated with the following steps: Enter keyboard setup Exit keyboard setup SHIFT, ALT, CTRL, BACKSPACE keys Keyboard keys (SHIFT, ALT, CTRL, BACKSPACE excluded) These signals facilitate the selection of those characters requiring more than one key...
AOCPCOHMHNGNENEIEPANHOGOCK AHHPMBAMDKEOFMHMLJALEGCEIK AKCBPJCJGIIJCMCEGKJIDLDDLK AEFBJLBGMHPLMPGPPHKFDNJHGK AAPHBAJJCBHPJOJIKGAGPFMNBK AFLFAINIOIDAKBHBLJNIIBHJJK DLDLLLLDDLLLLLLDDLDDDLDLLL USTOM DENTIFIER Custom Code Identifier AOCPBLHMHNGNENEIEPANHOGOCK Select a Datalogic Standard Code AHPNIJAMDKEOFMHMLJALEHFHIK AKCBPJCJGIIJCMCFGJLLDNBJNK Identifier from the Code Identifier Table AEFBJLBGMHPKNOGANCECFEMGGK AAPHBAJIDDGNCMJCAFDEFOFNHK in Appendix AEKFALLKNIIMEADJNKJEAODLJK DLDLLLLDDDLLLLLDLLLDDLDLLL Set the number of characters in the range 0-3, where 0 = Code ID disabled.
Page 45
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL EADERS Set Headers AOCLFLHMHNGNENEIEPANHOGOCK Set the number of characters in the AHPNIJAMDKEOFMHMLJALFEHEIK AKCBPJCJGIIJCMCFGINPLIOJPK range 00-10. AEFBJLBGMHPLMJBFJPEIPAKHGK AAPHBAJJDGFDNOEIJJLNEAOHDK Read the corresponding characters AHLFAJLDBHAAMIOOFKGGIFMIKK DLLLLLLDLDLLLLLDDDLDDLDLLL...
Page 48
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL Maximum Code Length APCPBLFMHNGNENEIEPANHOGOCK Read the number in the range AHPNIJAMDKEOFMHMLJAKEAEFIK AKCBPJCJGIIJCMCEGKPOPBMLNK 001-255. AEFBJLBGMHPLMLGGICCOGBFFGK AAPHBAJJDEGOIMFEFDHLBJMDDK AFLFAJOLIGEMENAFDGFAALAIIK DDDLLLLDDDLLLLLDLLDDDLDLDL Start-Stop Character Start-Stop Character Transmission - Disabled...
Page 49
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL Minimum Code Length APCLFPFOHNGNENEIEPANHOGOCK Read the number in the range AHPNIJAMDKEOFMHMLJAKFCAFIK AKCBPJCJGIIJCMCEHIJDPBJFLK 001-255. AEFBJLBGMHPKNPCINDMAAKPHGK AAPHBAJICACGOBDLDIAILGNFFK AHLFANONKLLMECDIFFMKMHALJK DDDLLLLDDDLLLLLDDDLDDLDLDL Maximum Code Length APCLFPFOFNGNENEIEPANHOGOCK Read the number in the range...
Page 50
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL Maximum Code Length APCLFLFOFNGNENEIEPANHOGOCK Read the number in the range AHPNIJAMDKEOFMHMLJALEFGHIK AKCBPJCJGIIJCMCEGMLCFAKFNK 001-255. AEFBJLBGMHPKNNGHFIFGDHMEGK AAPHBAJJDFBMCHEFKJCIDKMJDK AHKFAJOMLAJOIMBFEPFKKBCIKK DLLLLLLDDLDLLLLDDLDDDLDLLL 128 F AMILY Code 128 - Disabled...
Page 52
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL Maximum Code Length APCLBLFOFNGNENEIEPANHOGOCK Read the number in the range AHPNIJAMDKEOFMHMLJALEDAHIK AKCBPJCJGIIJCMCEGJMLKGPPPK 001-255. AEFBJLBGMHPKMKFDFMMJOOBHGK AAPHBAJJCBDNNGHKHKNHKCAJBK AEKFAINHJPFMGGDCLJBACEPKKK DDDLLLLDLDLLLLLDDLLDDLDLDL RSS F AMILY Disable RSS Expanded...
Enter Gun Configuration Exit and Save Gun Configuration AMHKGMHOFNGNENEIEPANHOGOCK AMHKCMHOFNGNENEIEPANHOGOCK AHPNIBAMDKEOFMHMLJALFCAFIK AHPNIBAMDKEOFMHMLJALFEGFIK AKCBPJCJGIIJCMCEGOODCCEDJK AKCBPJCJGIIJCMCEGLJKNEBJLK CONFIGURATION AEFBJLBGMHPLNPGLABJHFIAEGK AEFBJLBGMHPLMIFPAFAIIBNHGK AAPHBAJICCBGBIAFNLNLLAINDK AAPHBAJIDGDHOJDKAICECIENBK AFLFBPPCOIHKILNFFOCKOLJILK AGLFBOMJMHLIGBPCKIGAGOEKLK DLDDLDDLDDLLLLLDDDLDDLDLLL DDLDLDDLLLDLLLLDDDDDDLDLDL AFETY URATION Set Duration APCOFPHMFNGNENEIEPANHOGOCK Read a number in the range AHPNIJAMDKEOFMHMLJALFEAHIK AKCBPJCJGIIJCMCFHPKMDPJLLK 01-99, where 01 corresponds to AEFBJLBGMHPLNOGKLEGCNHNGGK AAPHBAJJDFEMPNPJOPBNJHLFFK 100 ms and 99 to 9.9 seconds.
LYNX™ D TEST CODE SYMBOLS Use these 1D and 2D test symbols to check that the reader is imaging and decoding properly, according to your configuration. UPC-A EAN-13 52637 48509 1 234567 000992 Code 39 (Standard) Code 128 PDF417 DataMatrix (Normal) DataMatrix (Inverse)
MAINTENANCE MAINTENANCE You do not need to perform regular preventative maintenance on the Lynx™ D reader. Do not try to open the case, because you might damage the interior electronic components and such action voids the warranty. You can keep your reader in good operating condition by: •...
LYNX™ D TECHNICAL FEATURES LYNX™ D432 / D432E Common Features Electrical Features Operating Voltage 10 to 30 V Power Consumption @ 12V (Stand-by) 110 mA @ 12V (Typical) 245 mA @ 10V (Peak current) 305 mA Communications Features Standard Interfaces RS232, Keyboard emulation AT IBM, , USB COM emulation, USB Keyboard emulation Proprietary Interfaces...
Page 63
TECHNICAL FEATURES LYNX™ D432 / D432E Common Features Optical Features 640 x 480 pixel element, 2D CMOS Array Sensor LED array Illuminator Wavelength In the range 630 ~ 670 nm Max. LED Output Power 0.896 mW LED Safety Class Class 1 to EN 60825-1 Visible Laser Diode Aiming System Wavelength...
Page 64
LYNX™ D LYNX™ D432 Optical Features Focus distance 115 mm Field of view 21.8° (H) x 16.7° (V) Horizontal field of view at 0.4d + 12 distance (d) in mm Vertical field of view at 0.3d + 9 distance (d) in mm Max Resolution Linear codes - mm (mils) DataMatrix –...
Page 65
TECHNICAL FEATURES LYNX™ D432E Optical Features Focus distance 65 mm Field of view 20° (H) x 15° (V) Horizontal field of view at 0.32d + 8.67 distance (d) in mm Vertical field of view at 0.24d + 6.50 distance (d) in mm Max Resolution Linear codes - mm (mils) DataMatrix –...
Page 71
Datalogic Scanning, Inc. 959 Terry Street Eugene, OR 97402 dichiara che declares that the déclare que le bescheinigt, daß das Gerät declare que el LYNX D432, 2D Reader LYNX D432 E, 2D Reader e tutti i suoi modelli and all its models et tous ses modèles...