Download Print this page
Jenn-Air JGR8750ADQ Installation Manual
Jenn-Air JGR8750ADQ Installation Manual

Jenn-Air JGR8750ADQ Installation Manual

Gas 30-inch free-standing and slide-in

Advertisement

Quick Links

INSTALLER:
LEAVE
THESE
INSTRUCTIONS
WITH THE APPLIANCE
INSTALLATION
MANUAL
Gas 30-inch
Free-standing
and Slide-in
PLEASE
KEEP THIS MANUAL
FOR FUTURE
REFERENCE
THE MANUAL IS INTENDED TO ASSIST IN THE INITIAL INSTALLATION
AND ADJUSTMENTS
OF THE RANGE.
Only qualified personnel should
install or service this range.
Read "Safety
Instructions"
in the
Use & Care book before using
range.
Improper
installation,
adjustment,
alteration,
service,
maintenance
or
use of range can result in serious
injury or property damage.
WARNING
• ALL RANGES CAN TIP AND
CAUSE INJURIES TO PERSONS.
• INSTALL
ANTI-TIP
DEVICES
PACKED WITH RANGE.
• FOLLOW ALL INSTALLATION
INSTRUCTIONS.
I Your
range may not be equipped
with
some of the features
referred
to in this manual'
CLEARANCE
DIMENSIONS
Range may be installed with zero inches clearance
adjacent to (against) combustible construction
at the rear
and on the sides below the cooktop. For complete
information in regard to the installation of wall cabinets
above the range and clearances to combustible wall
above the cooking top see the installation drawings. For
SAFETY CONSIDERATIONS
do not install a range in any
combustible cabinetry which is not in accord with the
installation drawings.
* NOTE: 30 inch dimension between cooking top and wall
cabinet shown on illustration does not apply to ranges
with an elevated oven. The 30 inch dimension may be
reduced to not less than 24 inches when the wall cabinets
in a domestic home are protected with fireproof materials
in accordance with American National Standards -
National Fuel Gas Code or in mobile homes when they
are protected with fireproof materials in accordance with
the Federal Standard for Mobile Home Construction and
Safety.
To eliminate the risk of burns or fire by reaching over
heated surface units, cabinet storage space located
above the surface units should be avoided. If cabinet
storage is to be provided, the risk can be reduced by
installing a range hood that projects horizontally a
minimum of 5 inches beyond the bottom of the cabinets.
CAUTION:
Some cabinets and building materials
are not designed to withstand the heat produced by the
normal safe operation of a listed appliance.
Discoloration or damage, such as delamination, may
occur.
8101 P375-60
(11-2000-00)

Advertisement

loading

Summary of Contents for Jenn-Air JGR8750ADQ

  • Page 1 INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE INSTALLATION MANUAL Gas 30-inch Free-standing and Slide-in PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE THE MANUAL IS INTENDED TO ASSIST IN THE INITIAL INSTALLATION AND ADJUSTMENTS OF THE RANGE. CLEARANCE DIMENSIONS Only qualified personnel should Range may be installed with zero inches clearance adjacent to (against) combustible construction at the rear...
  • Page 2: Installation Drawings

    INSTALLATION DRAWINGS ED GAS LINE LOCATION NON-SELF CLEANING MODELS. 1 • IDE FOR 120 VOLT GROUNDED ELECTRICAL OUTLET IN IHIS AREA. OUTLET MUST FLUSH. 13"W × g'H. AREA LOCATED g 3/_ ° ABOVE FLOOR, AND I I/2' FROIvl RIGHT WALL. 25"...
  • Page 3 ANY COMBUSTIBLE SURFACE /.-.------- 13" MAX. DEPTH ABOVE COOK TOP OF CABINETS O" CLEARANCE BETWEEN ADJACENT J-'_ COMBUSTIBLE CONSTRUCTION AND THE BACK AND SIDES OF THE RANGE BELOW THE COOKING SURFACE. 36" ART #9219-922 DIMENSION "A" SIDE CLEARANCE ABOVE COOKING SURFACE TOP BURNER RATE FOR...
  • Page 4 ANTI-TIP DEVICE INSTALLATION INSTRUCTIONS 1/8" pilot hole in the center of each hole as shown NOTE: A risk of range tip over exists if the appliance is in figure 2. (A nail or awl may be used if a drill is not installed in accordance with the installation not available).
  • Page 5 CONNECTING THE RANGE ELECTRIC SUPPLY NATURAL GAS SUPPLY LINE MUST HAVE A NATURAL The appliance, when installed, must be electrically GAS SERVtCE REGULATOR. INLET PRESSURE TO grounded in accordance with local codes or, in the THIS APPLIANCE SHOULD BE REDUCED TO A absence of local codes, with the National Electrical Code, ANSl/NFPA 70.
  • Page 6 Apply a non-corrosive leak detection fluid to all joints Gas SupplyConnectionsForRangesWith and fittings in the gas connection between the supply Appliance PressureRegulator line shut-off valve and the range. Include gas fittings LocatedIn The BottomOf Range and joints in the range if connections were disturbed during installation.
  • Page 7 RANGE ADJUSTMENTS Top Section - Gas Top Pilot Adjustment Top Burner Adjustment (See figure 6) All Top Burner Valves: The approximate height of the flame at the high or full-on position is shown below. Purge all air from supply system by turning on one top burner valve.
  • Page 8 Air Shutter - Oven Burner Removing Sealed Burner For Adjustment Or Service: The approximate length of the flame of oven burner is Mark ignitor location relative to main top with pencil. This a 1/2 inch distinct inner blue flame, figure 8. mark on the main top is used as a reference point when replacing the burner assembly to insure that the burner is tightened to its original position.
  • Page 9: Gas Conversion

    GAS CONVERSION General Appliance Pressure Regulator Conversion The unit appliance pressure regulator must be set to All ranges and cooktops are equipped with double coaxial match the type gas supply used. If converting from natural (universal) orifices and with a convertible appliance gas to LP gas, the appliance pressure regulator must be pressure regulator.
  • Page 10: Service/Parts Information

    ORIFICE CONVERSION From Natural Gas To LP/Propane Gas: FOR ALL TOP BURNER Change the appliance pressure regulator from OVEN SAFETY VALVE CONVERSION natural to LP setting. (See figure 12, 13 or 14). (EXCEPT EATON VALVE) Screw the burner orifice hoods down tight against the pins.

This manual is also suitable for:

Jgr8750adbJgr8750adwJgr8750ada