Page 1
Quick Start for Hardware Installation: Avaya G700 Media Gateway Avaya S8300 Media Server 555-233-150 Issue 8 February 2007...
Page 2
Avaya support Avaya provides a telephone number for you to use to report problems or to ask questions about your product. The support telephone number is 1-800-242-2121 in the United States. For additional support telephone...
2. If you are using the Avaya Installation Wizard to generate basic translations on an S8300 primary controller in a G700, get the customer’s Name and Number list file and the Custom Templates. Copy these files to your laptop. The Electronic Preinstallation Worksheet contains instructions for the Name/Number and Custom Templates files.
Information on the Avaya Installation Wizard options for ProVision is in the Electronic Preinstallation Worksheet. Laptop requirements The laptop PC that you use to access the S8300 and/or G700 and to launch the Avaya Installation Wizard must meet the following requirements: A minimum display resolution of 800 by 600 ●...
The following list of equipment contains items that may not be needed for your configuration — those items are specified as "optional" and may not be included in your inventory. Avaya G700 Media Gateway Chassis EXT1 EXT2 ALM PWR CPU MSTR...
Page 8
Optional Avaya MM722 2-port BRI Media Module Optional Avaya MM760 VoIP Media Module AVAYA Optional Expansion Module. X330T16 Optional C360 Converged Stackable Switch: C363T/C363-PWR C364T/C364-PWR Optional X330STK Octaplane Stacking Module. 8 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server...
DVD/CD-RW drive for S8300/S8400. ● Material ID: 700406267 Optional industrial-strength Compact Flash card and Compact Flash drive available through your Avaya sales representative. h1dccfla LAO 110306 Optional Uninterruptable Power Supply (UPS) for AC-Powered Gateways Only. Note: A stand-alone version of the Note: UPS is shown.
Page 10
Optional X330SC Short Cable. Note: The X3300SC Short Cable Note: is sometimes shipped attached to the X3300STK Octaplane Stacking Module. Optional X3300RC Redundancy Cable. Optional X3300 LC Long Cable. 10 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server...
Page 11
Optional USB Cable and Adapter for use with the USB modem. Crossover Ethernet Cable (CAT5) Serial or "Console" Cable and Adapter Ground wire. Issue 8 February 2007...
Page 12
Conduct Equipment Inventory Optional AC Power Cord Optional DC Power Cord. Feet used for table mounting. 12 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server...
Chapter 3: Mount Media Gateway 1. Wear an anti-static ground wrist strap and attach to an approved ground. 2. For rack mount, install the mounting brackets on the left and right sides of the gateway chassis using the flathead screws from the bracket packet.
Page 14
5. Connect the ground wire to the ground conductor on the back of the media gateway. 6. Attach the other end of the ground wire to an approved ground. 14 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server...
Chapter 4: Install Octaplane Stacking Module Note: Complete these steps only if you are connecting more than one G700 Media Note: Gateway in a stack configuration. 1. Remove the blank faceplate from the Octaplane slot on the back of the media gateway.
Page 16
Install Octaplane Stacking Module 16 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server...
Chapter 5: Connect Media Gateways Note: Complete these steps only if you are connecting more than one G700 Media Note: Gateway in a stack configuration. 1. Using the gray X330SC short cables, connect the media gateways from the bottom up: Connect the light gray connector to the ●...
Page 18
Connect the dark gray connector of the ● gray X330LC long cable to the port labeled “Cable to lower unit” on the bottom unit of the stack 2. Multiple-stack redundancy 18 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server...
Complete these steps if you are installing an S8300 Media Server (configured as Note: the primary controller or as a Local Survivable Processor). 1. From the front of the G700 Media Gateway, remove the blank faceplate from slot V1. 2. For an S8300B, remove the LED module (located above slot V1) and place in an anti-static bag.
Page 20
6. Tighten the captive screws on the S8300. EXT1 EXT2 ALM PWR CPU MSTR LNK COL Tx FDX FC Hspd LAG SHUT DOWN OK TO REMOVE SERVICES USB1 USB2 EXT1 EXT2 20 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server...
Chapter 7: Install Media and Expansion Modules Note: In each gateway, a single expansion module can be installed in the lower left slot Note: only. If the S8300 is installed (in slot V1), up to 3 media modules can be installed in slots V2–V4.
Page 22
Install Media and Expansion Modules 22 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server...
Chapter 8: Install USB Modem and CD-ROM Drive USB Modem 1. Connect the USB cable to one of the USB ports on the faceplate of the S8300. 2. Following the instructions packaged with the modem, connect the other end of the USB cable to the modem.
Page 24
Install USB Modem and CD-ROM Drive 24 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server...
Chapter 9: Install UPS and Apply Power UPS (AC only) 1. The UPS is an option for AC-powered gateways only. From the back of the G700 Media Gateway, connect the Uninterruptable Power Supply (UPS) using the manufacturer’s instructions. Note: A stand-alone version of the Note: UPS is shown.
Page 26
1. Apply power to each media gateway by connecting the DC power cord. Note: There is no on/off switch. Note: The units will power up when connected. 26 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server...
Chapter 10: Connect the Laptop — G700 without an S8300 This section assumes the G700 does not contain an S8300 Media Server. Use the Gateway Installation Wizard from the laptop to enter the initial gateway configuration parameters. 1. Connect the RJ45 end of a serial...
Page 28
Ethernet ports (labeled Ext 1 and Ext 2) on the front of the G700. 2. Connect the other end of the cable to a LAN connector. 28 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server...
Chapter 11: Connect the Laptop — G700 with S8300 This section assumes the G700 has an S8300 Media Server installed. 1. Connect a crossover Ethernet cable to the Services port on the faceplate of the S8300 Media Server. 2. Connect the other end of the cable to the Ethernet port on the laptop.
Page 30
Logon page. 13. Log in to the S8300 Media Server with the craft login and password for initial installation. 30 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server...
Page 31
1. Connect a straight Ethernet cable to one of the Ethernet ports (labeled Ext 1 EXT1 EXT2 and Ext 2) on the front of the G700. 2. Connect the other end of the cable to a LAN connector. Issue 8 February 2007...
Page 32
4. Go to the Maintenance Web Interface and select Modem in the Security Category. 5. Select the box labeled "Enable modem for unlimited incoming calls" an click Submit. 32 Quick Start for Hardware Installation: G700 Media Gateway & S8300 Media Server...