Hardware Setup; Remote Id - Integra DTR-70.3 Instruction Manual

■
BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX,
TUNER, TV/CD, PHONO, PORT, NET, USB
Off:
No trigger signal is output.
A 12-volt trigger signal is output when the connected
component is selected as the source for:
Main, Zone 2, Main/Zone 2, Zone 3, Main/Zone 3,
Zone 2/Zone 3, Main/Zone 2/Zone 3, Zone 4,
Main/Zone 4, Zone 2/Zone 4, Main/Zone 2/Zone 4,
Zone 3/Zone 4, Main/Zone 3/Zone 4,
Zone 2/Zone 3/Zone 4, Main/Zone 2/Zone 3/Zone 4
Note
• By default, all input sources on the "12V Trigger A Setup"
menu are set to "Main", those on "12V Trigger B Setup" are set
to "Main/Zone 2/Zone 3/Zone 4", and those on "12V Trigger
C Setup" are set to "Zone 2".

Hardware Setup

Main menu Hardware Setup

Remote ID

■
Remote ID
1, 2, or 3
When several Integra/Onkyo components are used in the
same room, their remote ID codes may overlap. To
differentiate the AV receiver from the other components,
you can change its remote ID from "1", to "2" or "3".
Note
• If you do change the AV receiver's remote ID, be sure to change
the remote controller to the same ID (see below), otherwise, you
won't be able to control it with the remote controller.
Changing the remote controller's ID
1 While holding down Receiver, press and hold
down Setup until Receiver lights (about 3
seconds) (➔ page 45).
2
Use the number buttons to enter ID 1, 2, or 3.
Receiver flashes twice.
Multi Zone
■
Zone 2 Out, Zone 3 Out
Fixed:
The Zone 2/3 volume must be set on the amp in that
zone.
Variable:
The Zone 2/3 volume can be set on the AV receiver.
If you've connected your Zone 2/3 speakers to an amp
with no volume control, set the "Zone 2 Out" and
"Zone 3 Out" setting, respectively, to "Variable" so that
you can set the volume, balance, and tone of zone 2 and
volume of zone 3 on the AV receiver.
■
Zone 2 Maximum Volume,
Zone 3 Maximum Volume,
Zone 4 Maximum Volume
Off, 50 to 99 (Absolute display)
Off, –32dB to +17dB (Relative display)
With this setting, you can limit the maximum volume for
Zone 2/3/4.
■
Zone 2 Power On Volume,
Zone 3 Power On Volume,
Zone 4 Power On Volume
Last, Min, 1 to 99 or Max (Absolute display)
Last, – dB, –81dB to +18dB (Relative display)
This setting determines what the volume will be for
Zone 2/3/4 each time the AV receiver is turned on.
To use the same volume level as when the AV receiver
was last turned off, select "Last".
The "Zone 2 Power On Volume", "Zone 3 Power On
Volume", and "Zone 4 Power On Volume" cannot be set
higher than the "Zone 2 Maximum Volume", "Zone 3
Maximum Volume", and "Zone 4 Maximum Volume"
setting.
■
Zone 2 Component Video Out
Yes:
Select if a TV in Zone 2 is connected to the
COMPONENT VIDEO ZONE 2 OUT.
No:
Select if no TV in Zone 2 is connected to the
COMPONENT VIDEO ZONE 2 OUT.
If you've connected the COMPONENT VIDEO ZONE 2
OUT to a TV in Zone 2, set this setting to "Yes".
Note
• If the "Zone 2 Component Video Out" setting is set to "No",
the same video signal as COMPONENT VIDEO MONITOR
OUT is output from ZONE 2 OUT (component).
En
63