Table of Contents
Advertisement
Quick Links
REV.2006.04
INSTALL GUIDE
www.ultrastarters.com
Technical Support: 866-698-5872 ext 0
support@ultrastarters.com
Warning
CARBON MONOXIDE MAY CAUSE SERIOUS INJURY, EVEN DEATH!
It is the sole responsibility of the user to place the system in Service Mode
when parking in an enclosed area ex: garage, partially enclosed area
ex: carport, or when the vehicle is being serviced.
Advertisement
Table of Contents
Related Manuals for Ultra Start G-Series
Summary of Contents for Ultra Start G-Series
- Page 1 REV.2006.04 INSTALL GUIDE www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com Warning CARBON MONOXIDE MAY CAUSE SERIOUS INJURY, EVEN DEATH! It is the sole responsibility of the user to place the system in Service Mode when parking in an enclosed area ex: garage, partially enclosed area ex: carport, or when the vehicle is being serviced.
-
Page 2: Table Of Contents
INSTALL GUIDE PAGE 2 Table of Contents Table of Contents Page 2 Feature List Page 3 Installer Notes Wiring Diagrams Pages 4-5 Auto/Optional Tach Learn Page 6 System Reset Page 7 Transmitter Programming Entering Program Mode Page 8 Quick View Programming Pages 9 Program Menu 1 Pages 10-11... -
Page 3: Feature List
INSTALL GUIDE PAGE 3 Feature List - Auto Tach learning. - Run Time: 4/15/45 minutes - Door locks: .125s/.75s/3s / Double unlock / Ignition lock/unlock - Horn output 5ms/10ms/50ms - Timer or Cold Start (LT series) with 4 different start intervals - Programmable Wait to Start or (+/-) diesel Glow plug input - Ground While Running/Anti-grind protection/Starter kill - System Override Protection/Service Mode (Valet) -
Page 4: Wiring Diagrams
INSTALL GUIDE PAGE 4 Wiring Diagram Starter Output (+) YELLOW Heater/Accessory Output (+) GREEN 12volt Input (+)30amp 12volt Input (+)30amp Selectable Output (+)* WHITE* Ignition Output (+) BLUE Diesel Wait To Start Input (+or-) BLUE Brake Switch Input (+) PINK Horn Output (-) WHITE/BLUE System Ground Input (-) -
Page 5: Wiring Diagrams
INSTALL GUIDE PAGE 5 Wiring Diagram Door Lock Output (-)250ma GREEN 12volt Output (+)250ma RED* (see notes above) Door Unlock Output (-)250ma BLUE ACTIVE RF ANTENNA** Status Led’s Program Button **The antenna MUST be connected for the system to operate Bypass module** Expansion module** *The centre pin of the keyless entry harness is ONLY available with plug-in... -
Page 6: Auto/Optional Tach Learn
INSTALL GUIDE PAGE 6 Auto/Optional Tach Learn IMPORTANT! The system must be Tach Learned before remote starting. Auto Tach Learn: Start the vehicle with the key. To confirm that a proper tach signal is detected the system will flash the park lights and the horn (optional) will honk three times. -
Page 7: System Reset
INSTALL GUIDE PAGE 7 System Reset A system reset will clear any changes made to the Program Menu’s as well as the Tach setting. When the system reset is complete the system must be Auto Tach learned before the remote starter will operate. -
Page 8: Entering Program Mode
INSTALL GUIDE PAGE 8 Entering Program Mode For Menu 1, For Menu 2, Ignition 3x Press and For Menu 3, For Menu 4, press the press the On/Off Release the press the press the button On/Off On Program Button button button button STEP 1: With the ignition key in the “Off”... -
Page 9: Quick View Programming
INSTALL GUIDE PAGE 9 Quick View Programming 1 Flash 2 Flashes 3 Flashes 4 Flashes Menu 1 - Lock Button 1. Ignition Lock Disabled Enabled Lock Only 2. Door Lock/Unlock Pulses 0.750 sec. Pulse 0.125 sec. Pulse 3 sec. Pulse Double Unlock 3. - Page 10 INSTALL GUIDE PAGE 10 Menu 1 Press and Press and Press and Release Ignition 3x Press and Hold Release the Release the the Program Button On/Off the Program Button Program button for # of Times for On/Off On to Change Option Button Menu 1 Setting Chosen...
- Page 11 INSTALL GUIDE PAGE 11 Menu 1 - continued... Setting 5 Horn Honk Output (12 pin auxiliary connector pin 3) 1) All confirmation 1 Flash/Honk Horn honk confirmation on all functions. 2) Lock/ Unlock enabled 2 Flashes/Honks Horn honk confirmation on Lock/Unlock only 3) 2nd Lock press 3 Flashes/Honks Horn honk confirmation on 2nd Lock press..
- Page 12 INSTALL GUIDE PAGE 12 Menu 2 Press and Press and Release Press and Hold Press and Ignition 3x Release the the Program Button the Program Button Release the On/Off Program # of Times for to Change Option button for On/Off On Button Setting Chosen Menu 2...
- Page 13 INSTALL GUIDE PAGE 13 Menu 2 - continued... Setting 6 Negative Park Light/ GWR (12 pin auxiliary connector pin 11) 1) Negative Park Light Output 1 Flash/Honk (-) 250ma output with lock. 2) GWR/ Anti-Grind Output 2 Flashes/Honks (-) 250ma output while remote starter active. Press &...
- Page 14 INSTALL GUIDE PAGE 14 Menu 3 Press and Press and Release Press and Hold Press and Ignition 3x Release the the Program Button the Program Button Release the On/Off Program Number of Times for to Change Option button for On/Off On Button Setting Chosen Menu 3...
- Page 15 INSTALL GUIDE PAGE 15 Menu 4 Press and Press and Press and Release Press and Hold Ignition 3x Release the Release the the Program Button the Program Button On/Off Program # of Times for to Change Option button for On/Off On Button Setting Chosen Menu 4...
-
Page 16: Diagnostics
INSTALL GUIDE PAGE 16 DIAGNOSTICS If the remote starter does not activate when the start button is pressed the park lights will flash a diagnostic to indicate what shutdown input has been triggered. For example: If the button is pressed the park lights flash 3 times slowly. Looking at the chart below this would indicate that the system is in Service Mode, simply follow the instructions listed in the owners manual on exiting Service Mode and the remote starter will begin to function as normal.