1. Manuals
  2. Brands
  3. Ultra Start Manuals
  4. Car Alarm
  5. 600 SERIES
  6. Install manual

Ultra Start 600 Series Install Manual

Remote vehicle security system
Hide thumbs Also See for 600 Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual, Installation Manual
INSTALL GUIDE
600 Series Remote Vehicle Security System
WWW.ULTRASTARTERS.COM
Technical Support- 866.698.5872
FCC/ID Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance
void the user's authority to operate this devise.

Advertisement

Table of Contents
loading

Related Manuals for Ultra Start 600 Series

Summary of Contents for Ultra Start 600 Series

  • Page 1 INSTALL GUIDE 600 Series Remote Vehicle Security System WWW.ULTRASTARTERS.COM Technical Support- 866.698.5872 FCC/ID Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

  • Page 2: Table Of Contents

    INSTALL GUIDE PAGE 2 Table of Contents Table of Contents Components 600 Wiring Diagram Installation Tips Pre-Installation Suggestions Installation Suggestions Mounting The Module Installing The LED Installing The Program Button Connecting The Starter Disable Connecting The Dome Light Supervision Under Hood Connections Mounting The Siren Wire Connectors 14 Pin Main Harness Connector...

  • Page 3: Wiring Diagram

    SECURITY SYSTEM Wiring Diagram Built-in Starter Disable relay (Normally Connected 87a & 30). See page. 5 500ma Output Programmable - Menu 2 Connect to (-) door pin (-) Input Connect to hood pin (-) Input Connect to (+) door pin (+) Input Connect to Siren 3amp Output...

  • Page 4: Installation

    INSTALL GUIDE PAGE 4 Recommended Pre-Installation Procedures BEFORE STARTING INSTALLATION: - Discuss the optional system features with the customer. - Take a few minutes to review the installation and owners manuals. - Do a walk around the vehicle and check for any damage. - If installing a LED discuss the placement with customer before installing.

  • Page 5: Pin Connector

    SECURITY SYSTEM 14 Pin Connector Pink Channel 4 Output Green (-) Door Input Blue (-) Hood Input Purple (+) Door Input Brown (+) Siren Output White (+) Park lights Blk/White (+/-) Dome Light Blk/White (+/-) Dome Light Orange (-) When Armed Grey (-) Trunk Release Yellow...

  • Page 6: Test The System

    INSTALL GUIDE PAGE 6 Quick Start Install Step 1 - Connect All Of the Following Wires 14 Pin Power Connector Black Yellow White Green* Purple* *Test for door pin type (Positive or Negative) then connect the appropriate wire (Green or Purple) Step 2- Plug-In The Module When all the connections are done, the control module can be plugged in.

  • Page 7: Programming

    SECURITY SYSTEM Programming Overview Program mode allows you to adjust the settings and options of your system. Your system has been intelligently designed by installers with years of experience. The system’s default settings do not require any program changes in most cases. However, this system does incorporate a highly advanced programming system that includes 2 menus with numerous options and settings that can be easily adjusted for custom installations and applications.
  • Page 8 INSTALL GUIDE PAGE 8 Menu 1 - User Settings Setting 1- Ignition Auto Lock 1 Ignition Lock & Unlock Enabled 2 Ignition Lock Only *3 Ignition Auto Lock Disabled Press the Valet Switch 1 time to select setting 1 (This will be confirmed by 1 LED flashes) Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
  • Page 9 SECURITY SYSTEM Menu 2- Alarm Settings Setting 1 - Car Finder/ 5th Channel 1 Car Finder OFF *2 Car Finder ON **To operate the 5th channel on button #4, setting 7 must be programmed for 5th channel output. Press the Valet Switch 1 time to select setting 1 (This will be confirmed by 1 LED flashes) Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.

  • Page 10: Operations

    INSTALL GUIDE PAGE 10 First Car Operation Press Once to Lock the doors and arm the alarm. Hold for Panic Mode. Press a second time and hold for Constant Lock Output. Press once to unlock the doors and disarm the alarm Press and hold for the Trunk / Aux Output Press this button to activate the 4th channel output.
  • Page 11 SECURITY SYSTEM System Service Mode ACTIVATING SERVICE MODE 1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp five times to confirm that the system is in Service Mode. 2.

  • Page 12: Diagnostics

    INSTALL GUIDE PAGE 12 Diagnostics Alarm Diagnostics If the alarm system is triggered while armed, the system will retain in memory the cause of the trigger. The diagnostics can then be used to determine what the cause of the trigger was. When disarming the alarm, the siren/horn will chirp 3 times instead of the usual 2 times to indicate the alarm had been triggered.

Table of Contents