Table of Contents
Advertisement
MAN-DEH-P7900UB-GB.fm Page 28 Wednesday, February 21, 2007 11:20 AM
Operating this unit
Switching the dimmer setting
To prevent the display from being too bright at night, the display is automatically
dimmed when the car's headlights are turned on. You can turn the dimmer on or off.
1. Use MULTI-CONTROL to select Dimmer.
2. Press MULTI-CONTROL to turn dimmer on.
• To turn dimmer off, press MULTI-CONTROL again.
Adjusting the brightness
You can adjust the display brightness. Initially this mode is set to 12.
1. Use MULTI-CONTROL to select Brightness.
2. Push MULTI-CONTROL left or right to adjust the brightness level.
0 to 15 is displayed as the level is increased or decreased.
• When dimmer is functioning, the brightness level can be adjusted 0 to 10.
Setting the rear output and subwoofer controller
This unit's rear output (rear speaker leads output and RCA rear output) can be used
for full-range speaker (Rear SP :F.Range) or subwoofer (Rear SP :S/W) connection.
If you switch the rear output setting to Rear SP :S/W, you can connect a rear speaker
lead directly to a subwoofer without using an auxiliary amp.
Initially, the unit is set for rear full-range speaker connection (Rear SP :F.Range).
1. Use MULTI-CONTROL to select S/W control.
2. Press MULTI-CONTROL to switch the rear output setting.
Pressing MULTI-CONTROL will switch between Rear SP :F.Range (full-range
speaker) and Rear SP :S/W (subwoofer) and that status will be displayed.
• When no subwoofer is connected to the rear output, select Rear SP :F.Range.
• When a subwoofer is connected to the rear output, set for subwoofer Rear SP :S/W.
Notes
• Even if you change this setting, there is no output unless you turn the subwoofer output on
(refer to "Using subwoofer output" on page 25).
• If you change this setting, subwoofer output in the audio menu return to the factory settings.
• Both rear speaker leads outputs and RCA rear output are switched simultaneously in this
setting.
Switching the sound muting/attenuation
Sound from this system is muted or attenuated automatically when the signal from the
equipment with mute function is received.
• The sound is muted or attenuated, MUTE or ATT are displayed and no audio
adjustment is possible.
• Sound from this system returns to normal when the muting or attenuation is
canceled.
1. Use MULTI-CONTROL to select Mute.
2. Press MULTI-CONTROL to switch the telephone muting/attenuation.
Pressing MULTI-CONTROL will switch between TEL ATT (attenuation) and TEL
mute (muting) and that status will be displayed.
Switching the feature demo
The feature demo automatically starts when power to this unit is turned off while the
ignition switch is set to ACC or ON.
1. Use MULTI-CONTROL to select Demonstration.
2. Press MULTI-CONTROL to turn the feature demo on.
• To turn the feature demo off, press MULTI-CONTROL again.
Notes
• Remember that if the feature demo continues operating when the car engine is turned off, it
may drain battery power.
• You can also turn on or off feature demo by pressing DISPLAY while this unit is turned off.
For more details, see "Feature demo mode" on page 9.
Switching the reverse mode
If you do not perform an operation within about 30 seconds, screen indications start to
reverse, and then continue reversing every 10 seconds.
1. Use MULTI-CONTROL to select Reverse mode.
2. Press MULTI-CONTROL to turn the reverse mode on.
• To turn the reverse mode off, press MULTI-CONTROL again.
Note
• You can also turn on or off reverse mode by pressing BAND while this unit is turned off. For
more details, see "Reverse mode" on page 9.
28
Advertisement
Table of Contents
