Microtek ScanMaker i460 Start Here Manual
  1. Manuals
  2. Brands
  3. Microtek Manuals
  4. Scanner
  5. ScanMaker i460
  6. Start here manual

Microtek ScanMaker i460 Start Here Manual

Hide thumbs Also See for ScanMaker i460:
Table of Contents

Advertisement

Quick Links

Download this manual
Start Here
Installing your Microtek ScanMaker i460
Step 1:
Unpack your scanner package and check for
major components.
1. ScanMaker i460 scanner
2. Power adapter
3. Software CDs/DVDs
4. Hi-Speed USB cable
5. LightLid 35 IV*
* The LightLid 35 IV is either as a standard equipment or an
optional accessory depending on the scanner configuration that
you purchased.
Step 2:
Important: Do not remove the yellow stickers from your
scanner until you are told to do so. You must install software
before connecting your scanner.
Always close any open programs and turn off Anti-virus
utilities before installing software.
PC:
A. Place the Microtek Software CD/DVD
into a drive, and follow the on-screen
instructions to install the scanner
driver and software.
B. Restart your computer at the end of
all software installation.
NOTE: If the Microtek Software Installer screen does
not come up automatically, double-click the
following in succession: "My Computer"; the CD/
DVD-ROM icon; then cdsetup.exe to start the
installer program.
Copyright © 2013 Microtek International, Inc. http://www.microtek.com
I49-004750 B, September 2013
Unpack Contents
Install Software
1
5
MAC:
A. Place the Microtek Software CD/DVD
(ScanPotter) into a drive, and double-click
the ScanPotter installer icon to install
ScanPotter.
B. Install the remaining software
components, then restart your computer
at the end of all software installation.
NOTE: After rebooting your Macintosh, the Microtek
software will attempt to locate your scanner on the
system. Since this is your first install and you have not
yet connected the scanner, simply ignore the message
that appears and proceed to the next step.
1
2
3
4

Advertisement

Table of Contents
loading

Related Manuals for Microtek ScanMaker i460

Summary of Contents for Microtek ScanMaker i460

  • Page 1 NOTE: If the Microtek Software Installer screen does not come up automatically, double-click the NOTE: After rebooting your Macintosh, the Microtek following in succession: “My Computer”; the CD/ software will attempt to locate your scanner on the DVD-ROM icon;...

  • Page 2: Unlock Scanner

    Step 3: Unlock Scanner A. Remove the yellow “Step 3” sticker from your scanner. B. With the scanner power off, tilt the back left corner of the scanner to see the locking switch at the bottom. C. Push the locking switch to the position as indicated in the graphic, with the icon on the lock showing as “Unlocked”.

  • Page 3: To The Hi-Speed Usb Cable

    LED (orange) LED (green) Scanner Buttons The ScanMaker i460 is equipped with six scanner buttons, providing quick access to the most frequently used functions. These buttons are WEB, PDF, OCR, E-mail, Copy, and Scan. WEB: Scans the image and directly links to your assigned photo-sharing website.
  • Page 4 Using the LightLid 35 IV NOTE: If your scanner configuration does not contain the LightLid 35 IV and you do not have intention to use this device, please ignore this section. Connecting the LightLid 35 IV 1. Remove the scanner lid. 2.

  • Page 5: Scanning Photos

    Also, it allows you to specify an application to open the image. Theme – Changes the appearance of the control panel for the EZ mode. NOTE: For details about how to use the ScanWizard EZ‘s Advanced Mode and Professional Mode, refer to the ScanMaker i460 Supplement.

  • Page 6: Scanning Film

    Scanning Film 1. Place the film. To scan film, use the LightLid 35 IV. Refer to “Using the LightLid 35 IV” in this guide to load film. 2. Launch ScanWizard EZ. Follow the step 2 in “Scanning Photos” on previous page to launch ScanWizard EZ. 3.
  • Page 7 9. Click the Scan button to start scanning. NOTE: For details on scanning photos and film, see the ScanMaker i460 Supplement in the Microtek Software CD/DVD.
  • Page 8 Click the Scan Settings button Scan frame to switch back to the default (enclosed by dotted lines) control panel of ScanPotter Click the Image Settings button to switch to a window where contains a composite display of nine- image-effects (Filter column) and additional image correction tools (Additional Adjustment...
  • Page 9 Problems? The LEDs on the button panel indicate the status of the scanner. On - Scanner is on Both on - Ready to scan Flashing - Scanning or error happened LED (orange) Off - Scanner is off LED (green) If you encounter any problems, check the section below and follow the suggested solution if your problem is listed.
  • Page 10 Finally, select and click the title of the manual you wish to view. Missing Items If your package is missing items, please call the Microtek Customer Service Department. Drivers & Software Upgrades After you finish the installation of software, if you found that the installed drivers and software cannot run your product or your computer system properly later, please go to the Microtek Download Service site at ww7.microtek.com.tw/service.php to download...

Table of Contents