Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Built-In Liquid Propane Gas Grill Installation Guide
Vieluxe
®
(Model #: 360251)
LOCATING YOUR GRILL
When determining a suitable location for your Vieluxe
proximity to traffic paths, and keeping any gas supply lines as short as possible. Never locate the Vieluxe
breezeway, shed, under an unprotected overhang, or other enclosed area. Locate the grill and structure so there is enough room to
safely evacuate the area in case of a fire.
CLEARANCE FROM SURFACES OR STRUCTURES
WARNING: Clearance from any surface or structure is 26 inches from the back and sides
of the grill. Refer to "Typical Gas Supply Installation" before starting installation.
WARNING: The structure, "island", countertops, and adjacent work areas for the built-in
grill installation must be built from non-combustable materials only.
NOTE: If you have questions on what materials are considered non-combustable, contact you
local building materials supplier or fire department.
27" Built-In Grill
THIS GAS APPLIANCE IS DESIGNED FOR OUTDOOR USE ONLY.
®
gas grill installation, give attention to concerns such as exposure to wind,
24 inches min. for lid clearance
Vieluxe
26 inches Any Surface
Grill Frame
®
39" Built-In Grill
(Model #: 370251)
®
gas grill in a garage,
61265 021304
Advertisement
Table of Contents
Related Manuals for Weber Vieluxe 27 Built-In Grill
Summary of Contents for Weber Vieluxe 27 Built-In Grill
- Page 1 Built-In Liquid Propane Gas Grill Installation Guide Vieluxe ® 27" Built-In Grill Vieluxe ® 39" Built-In Grill (Model #: 360251) (Model #: 370251) THIS GAS APPLIANCE IS DESIGNED FOR OUTDOOR USE ONLY. LOCATING YOUR GRILL When determining a suitable location for your Vieluxe ®...
- Page 2 BUILT-IN STRUCTURE BUILT-IN GAS LINE CUTOUT DIMENSIONS LOCATIONS All dimensions are to finished surfaces. Plan View Front of Grill Structure Figure 3 BUILT-IN CUTOUT DIMENSIONS 27” grill 39” grill Tolerances ⁄ ⁄ ” ⁄ ” ⁄ ⁄ 36” 36” ⁄ Front View ⁄...
- Page 3 TYPICAL BULK PROPANE Gas line piping ■ Refer to the piping chart at the bottom of the page. GAS SUPPLY ■ The corrugated gas line from the manifold is INSTALLATION 48 inches long. Do not extend the gas line. ■ We have provided the means to make an SAE 45° WE RECOMMEND THAT THIS INSTALLATION BE flare connection.
- Page 4 TYPICAL BULK PROPANE TYPICAL 20LB PROPANE GAS SUPPLY GAS SUPPLY INSTALLATION (CONT.) INSTALLATION Gas line piping (continued) We strongly recommend that you use the Vieluxe Tank ® Cabinet (#36299) for installations using a 20 lb LP ■ Copper tubing must be tin-lined if the gas contains cylinder, mounted remotely in an “island”...
- Page 5 floor level. The ventilation openings should have a d. The remote LP cylinder enclosure should be total free area of not less than 10 square inches. constructed with non-combustible materials. The (This relates to 1/2 square of ventilation area, per remote LP cylinder enclosure should isolate the LP pound of stored fuel capacity).
-
Page 6: Connect Gas Supply
CONNECT GAS SUPPLY Test connections A 48" inch corrugated gas line is supplied with the grill. This line needs to pass through the gas inlet opening to All connections and joints must be thoroughly tested for the main gas supply. leaks in accordance with local codes and all listed procedures in the latest edition of ANSI Z223.1/NFPA 54. - Page 7 BUILT-IN GRILL INSTALLATION 5) Lower the grill down by adjusting the feet until the grill CAUTION: Use two people to lift and install the frame is resting on the "island" countertop. Vieluxe ® grill. Note: Make sure that the grill is level on the 1) Lift the grill out of the packaging.
-
Page 8: Floor Panel Installation
FLOOR PANEL VENTILATION INSTALLATION WARNING: Air holes must be provided in the structure at the top and bottom to provide Once your grill has been set into place and the adjustable ventilation in the event of a gas leak. feet have be set to level your grill to the "island" structure Air holes can be located in a low visibility area and should countertop, install the floor panel. -
Page 9: Assembly Supplies Needed
ASSEMBLY SUPPLIES NEEDED Note: Remove all packaging materials from the grill, the front, back, sides, inside the grill cart, and the bottom shipping platform. Once the packaging material is removed, carefully roll the grill off the shipping platform and lock the casters. REMOVE PACKAGED CONTENTS Assembly Warming Rack... -
Page 10: Install Flavorizer
INSTALL FLAVORIZER ® BARS Vieluxe ® 27" Built-In Parts required: (2) Flavorizer ® bar assemblies & (1) single Flavorizer ® bar. Set the Flavorizer ® bar assemblies and single Flavorizer ® bars front to back over the burners in the slots of the Flavorizer ®... -
Page 11: Install Smoker
INSTALL SMOKER Parts required: smoker box and smoker flues. Set the smoker box into the left side of the cooking box next to the Flavorizer ® bars. Then insert smoker flues with tabs into the cut-out of smoker box. The flues need to lay flat on top of the Flavorizer ®... -
Page 12: Install Warming Rack
INSTALL WARMING RACK Part required: warming rack. Install the warming rack into the slots at the right and left side of the cooking box. Vieluxe ® 27" Built-In Vieluxe 39" Built-In ® INSTALL BOTTOM TRAY Parts required: bottom tray and catch pan holder. Note: It will be easier to install the catch pan holder by removing the catch pan from the holder. -
Page 13: Install Catch Pan
WARNING: The storage space under the cooking module is intended for storage of nonflammable items only. © 2004 Weber-Stephen Product Co.. Vieluxe is a registered U.S. trademark of Weber-Stephen Products Co., ® 200 East Daniels Road, Palatine, IL 60067-6266. U.S.A. 1-866-VIELUXE.