Page 3
Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified using the procedures described in this manual, turn off the power, unplug the machine, then contact your authorized TOSHIBA TEC representative for assistance. This symbol indicates warning items (including cautions).
Page 4
Place the machine on a stable and level surface. Utilize our maintenance services. After purchasing the machine, contact your authorized TOSHIBA TEC representative for assistance once a year to have the inside of the machine cleaned. Otherwise, dust will build up inside the machines and may cause a fire or a malfunction.
1. TO OUR CUSTOMERS 1. TO OUR CUSTOMERS Thank you for choosing the TEC electronic cash register MA-1535 series. This instruction manual provides a description of the functions and handling of this register and should be read carefully to ensure optimum performance. Since every consideration has been given to safety and reliability, there is no danger of damaging the machine by incorrect operation.
3. APPEARANCE AND NOMENCLATURE EO1-11148 3. APPEARANCE AND NOMENCLATURE 3. APPEARANCE AND NOMENCLATURE Customer Display COM3 COM2 COM1 Printer Cover Operator Display Receipt Outlet Journal Window Interface Connectors Control Lock Keyboard Power Cord Printer Cover Display (Operator and Customer) The cover for the Receipt or Journal paper Used to confirm the entry contents and the holder and the printer.
, and Z. S Key: The S key is used by the service person from TOSHIBA TEC representative to access any position. To prevent programmed data and sales data from being changed or cleared by mistake, do not use this key without instructions of our TOSHIBA TEC representative.
5. DISPLAY EO1-11148 5.1 Upper Row (10-digit Alphanumeric Display) 5. DISPLAY The operator display is located at the top of the register just above the keyboard. The customer display can be fixed as a rear display. It can be moved horizontally, and thus is fully adjustable according to the position of the customer.
Page 12
5. DISPLAY EO1-11148 5.1 Upper Row (10-digit Alphanumeric Display) Error Messages When an error occurs, an error message (programmable) is displayed in the upper row, and an error code is in the lower row with an error buzzer sound (a long tone). For the error messages and error codes, see the table on the following page.
Low Battery This lamp turns on when the voltage of the ECR’s backup battery voltage is dropping. When this lamp lights, please contact your nearest TOSHIBA TEC representative as the programming data and sales data are backed up by this battery.
6. KEYBOARD EO1-11148 6.1 Keyboard Layout 6. KEYBOARD 6.1 Keyboard Layout The following is the standard keyboard layout for the MA-1535. Other keys not assigned to the keyboard above: [%+] [CHECK No.] [PLU ADD] [JP] [TAX DISPLAY] [000] [FUNCTION 1] to [FUNCTION 10] [PRICE 1] to [PRICE 3] [DP SHIFT] [FS/TL TEND]...
Page 15
6. KEYBOARD EO1-11148 6.2 Function of Each Key Reference Functions page Numeric Keys ---- 7 8 9 These keys are used to enter numeric values. Depressing the [00] 4 5 6 key once is the same as depressing the [0] key twice consecutively. 1 2 3 The [.] key is used to designate the decimal pint of a percentage rate 0 00 •...
Page 16
6. KEYBOARD EO1-11148 6.2 Function of Each Key Reference Functions page All Void Key 9-11 This key is used to cancel all the items entered in the current sale. VOID X/TIME Key This key is used to multiply a department, PLU, or Bottle Return item X/TIME entry by a quantity, and to auto-calculate and enter Triple Multiplication.
Page 17
6. KEYBOARD EO1-11148 6.2 Function of Each Key Reference Functions page PLU Add Key This key is used to add a PLU item that has not been programmed in the PLU table file, to the PLU Additional Table file. Journal Print Key 9-14 This key is used to print the store message, date, the register No.
7. CASHIER SIGNING OPERATIONS EO1-11148 7.1 Cashier Code Entry 7. CASHIER SIGNING OPERATIONS 7.1 Cashier Code Entry Cashier in operation is specified by entering a cashier number. One operation should be finished under the same cashier. Cashiers cannot be changed until the transaction is finished unless the cashier interrupt function is effective.
Page 19
7. CASHIER SIGNING OPERATIONS EO1-11148 7.2 Cashier Pass Code When a cashier pass code has been already programmed, enter the cashier number and press the [LOG/RECEIPT] key. The following cashier pass code prompt display will appear. When each digit is entered, the display will change as the example below. Example : When 2 digits are entered.
7. CASHIER SIGNING OPERATIONS EO1-11148 7.3 Cashier Interrupt Operation 7.3 Cashier Interrupt Operation By switching the Cashier during a sale, interruptions by other cashiers with sale items are allowed. Receipt-Off Mode (i.e. Receipt OFF Indicator is illuminated.) CONDITION Control Lock: REG Operation Example 1 (Single-cashier Interruption) Cashier 1 Cashier 2...
Page 21
7. CASHIER SIGNING OPERATIONS EO1-11148 7.3 Cashier Interrupt Operation (1) Sale item entries started by Cashier 1. (2) Switching Cashier 1 to Cashier 2 (interruption by Cashier 2) (3) Sale item entries by Cashier 2 (4) Switching Cashier 2 to Cashier 3 (interruption by Cashier 3) (5) Sale item entries and finalization by Cashier 3 (6) Switching Cashier 3 to Cashier 2 (7) Cashier 2 resumes his/her own entries and finalizes the sale.
7. CASHIER SIGNING OPERATIONS EO1-11148 7.4 Training Mode Start and End Depressing the [RECEIPT ISSUE] (Post-receipt) key after finalizing each cashier’s own entries with print and issue a receipt of his/her entries. The post-receipt of each cashier’s entries is available any time after finalizing his/her own entries until another sale is started by his/her Cashier.
8. INSTALLING AND REPLACING THE RECEIPT AND JOURNAL ROLLS EO1-11148 8.1 Installing/Replacing the Receipt Roll 8. INSTALLING AND REPLACING THE RECEIPT AND JOURNAL ROLLS WARNING! Care must be taken not to injure yourself with the paper cutter. Turn the control lock to the REG position using a Mode Selector Key to perform the paper roll installation described in this chapter.
8. INSTALLING AND REPLACING THE RECEIPT AND JOURNAL ROLLS EO1-11148 8.2 Installing/Replacing the Journal Roll Insert the paper end into the receipt inlet behind the printer. Then, manually feed the paper into #/NS X/TIME the printer while pressing the [RF] key until about 4 inches (about 10cm) of paper comes out of the printer.
Page 25
8. INSTALLING AND REPLACING THE RECEIPT AND JOURNAL ROLLS EO1-11148 8.2 Installing/Replacing the Journal Roll Insert the paper end into the slit of the Take-up Reel and wind it around the reel two or three times. Then, set the Support Plate. Set the Journal Take-up Reel Ass’y into the Reel Holder.
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9. REGISTERING PROCEDURE AND PRINT FORMAT 9. REGISTERING PROCEDURE AND PRINT FORMAT WARNING! When opening the cash drawer, be careful not to let the drawer hit any person. Before starting sale entries, read through the following instructions: TRAINING MODE is available: If you are a beginner in operating this register, ask the store manager for practicing in the TRAINING MODE.
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.1 Displaying the Date and Time Displaying the Date and Time Each time the [X/TIME] key is pressed in the REG mode, time and date are displayed by turns in the AMOUNT area of the display. When the Control Lock position is changed or any entry operation starts, the displayed date or time disappears.
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.3 Loan Loan This operation is used to record the cash amounts and food stamps (US model only) loaned from the store as the change reserve in the drawer. (Must be operated outside a sale) OPERATION ⏐Cash amount loaned ⏐...
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.5 PLU Entry (Manual PLU Code Entry) PLU Entry (Manual PLU Code Entry) Each PLU is pre-programmed as the “PRESET” type (with a price programmed) or “OPEN” type (with no price programmed). Perform operation depending on the type selected. OPERATION Tomato 1.00T...
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.8 Link PLU Link PLU This entry is useful, when the PLU item entry should always be followed by another PLU item sale. Linked PLU is automatically registered together with entered PLU. PLU0000000000101 1.00 PLU0000000000102 2.00...
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.10 Quantity Extension (Multiplication) for DEPTs/PLUs 9.10 Quantity Extension (Multiplication) for DEPTs/PLUs OPERATION (1) Department Multiplication Open Department type ⏐Quantity⏐ [X/TIME] ⏐Price⏐ [Open DEPT] ⏐Quantity⏐ [X/TIME] ⏐Price⏐ [DEPT SHIFT] [DEPT] DEPT01 3.00 @ Preset Department type 15.00 ⏐Quantity⏐...
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.12 Urgent PLU Maintenance 9.12 Urgent PLU Maintenance This operation is intended to enter a PLU item not existing in the PLU file. OPERATION Error Message Depress [C] to cancel PLU Entry Operation is displayed.
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.17 Percent Discount, Percent Charge 9.17 Percent Discount, Percent Charge OPERATION ⏐Rate⏐ [%−] (or [%+]) Dept or PLU item entry (for discount/charge from/on an When a discount/charge rate (0.01 to 99.99%) is individual item) not preset to the [%+]/[%−] key.
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.20 Item Correct 9.20 Item Correct An Item Correct operation is used to delete the last item entered in a transaction. OPERATION DEPT01 3.00 DEPT02 2.00 CORR DEPT02 -2.00 Sales Item Entries [ITEM CORR] DEPT03 1.00 SUBTL...
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.23 Non-Add Number Print 9.23 Non-Add Number Print Non-add numbers can be entered and printed for future references, to indicate codes or numbers of customers, media checks, credit cards, etc. The entered numbers do not affect any sale total data. OPERATION 24-01-2002 #1234...
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.26 Tax Exemption 9.26 Tax Exemption (US Balance Only) OPERATION Selective Tax Exemption Examples) [TX1/M] [DEPT] Exemption from Tax 1 only [GST/M] [DEPT] Exemption from GST only All Tax Exemption [TX/EX] Exemption from All Taxes All Tax Exemption from Sale [TX/EX][AT/TL] 9.27...
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.29 Journal Print (Thailand Specification) 9.29 Journal Print (Thailand Specification) This operation prints the Store Message, Date, and Register No. on the journal. Journal-print Format STORE 1343 PEACH DRIVE Print contents by depressing the [JP] PHONE: 87-6437 key (Store Message, Date, Register Open...
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.32 Split Tendering 9.32 Split Tendering A Split Tendering operation is used to repeat short-tendering multiple times by the different media (allowed only when the media key is programmed to allow short-tendering). OPERATION Example 1) ⏐Check Amount Tendered⏐...
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.34 Sale Paid in Foreign Currencies 9.34 Sale Paid in Foreign Currencies OPERATION Amount Tendered [ST] |Foreign currency code| [CUR] [AT/TL] in Foreign Currency Display the entered Other media keys may be Mandatory for a Enter the foreign Displays the foreign currency...
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.36 Paid-out 9.36 Paid-out A paid-out transaction is used when money is removed from the drawer without totaling to a sale. (Must be operated outside a sale) OPERATION (1) Paid-Out with Domestic Currency 24-01-2002 #1234 ⏐Amount to be paid out⏐...
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.38 Function Key Entry 9.38 Function Key Entry A string of key operations is executed by pressing the [FUNCTION] key on which the operations have been preprogrammed. STORE OPERATION 1343 PEACH DRIVE PHONE: 87-6437 Open 8:00am to 7:00pm [FUNCTION] (...
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.40 Food Stamp Tendering (US Model Only) 9.40 Food Stamp Tendering (US Model Only) OPERATION ⏐Tendered Amount by Food Stamp⏐ [FS TL/TEND] [FS TL/TEND] Sale Finalization Displays the FOOD Stampable Total When the tendered amount by Food Stamp is less that the sale total, the sale is not finalized with the balance still due displayed.
9. REGISTERING PROCEDURE AND PRINT FORMAT EO1-11148 9.42 Endorsement (or France Check) Print 9.42 Endorsement (or France Check) Print OPERATION After operating the Insert the check or the Enter the Check No. (if required non-cash required slip into an so programmed), and media key (usually the optional Remote Slip then depress the...
9.43 Remote Slip Printer (Hardware Option) Operation The Remote Slip Printer may be connected to the MA-1535 series ECR as an optional device. The Remote Slip Printer will operate printing if a slip is properly inserted. 1. The remote slip printer will automatically activate printing when the slip has properly been set to the printer table.
10. ECR PRINTER MOTOR LOCK DETECTOR EO1-11148 10. ECR PRINTER MOTOR LOCK DETECTOR 10. ECR PRINTER MOTOR LOCK DETECTOR (1) This detects the printer motor lock condition caused by some trouble. (2) When such a condition is detected, the front display indicates “PRINTER” (Programmable). (3) To regain the normal condition, turn the power of the ECR to OFF, remove the cause of the motor lock, and then turn the power to ON again.
12. GENERAL MAINTENANCE EO1-11148 12.1 Removing Jammed Paper 12. GENERAL MAINTENANCE WARNING! Care must be taken not to injure yourself with the paper cutter. 12.1 Removing Jammed Paper 1. Turn the Control Lock to the OFF position using the Mode Selector Key.
12. GENERAL MAINTENANCE EO1-11148 12.2 Removing the Drawer 12.2 Removing the Drawer 1. Open the drawer, then take the Money Case out. 2. Pull the drawer out, and when it stops by the stopper, lift the drawer up and pull it again. 12.3 Media Slot The Media Slot provided at the front of the drawer is used to put non-cash media such as check in the...
12. GENERAL MAINTENANCE EO1-11148 12.5 Drawer Key 3. To remove the Partition from the Coin Case, pull the Partition upward. Set the Partition in the groove where you like, then push down the Partition. 4. To change the layout of the Bill Case, it is necessary to remove the Bill Holder.
• Rubbing the paper hard with nail or hard object may discolour the paper. • The paper end should not be pasted to the core. For further information please contact your authorised TOSHIBA TEC representative or authorised paper manufacturer. 13- 1...
Page 53
EO1-11148 MA-1535 SERIES TABLE OF CONTENTS Page 1. DAILY OPERATION FLOW -------------------------------------------------------------------------1- 1 2. OPERATIONS IN “[-]” MODE ----------------------------------------------------------------------2- 1 3. READ (X) AND RESET (Z) REPORTS -----------------------------------------------------------3- 1 Money Declaration ----------------------------------------------------------------------------------------- 3- 3 General Notes on Report Takings --------------------------------------------------------------------- 3- 3 Report Samples -------------------------------------------------------------------------------------------- 3- 4 3.3.1...
Page 54
EO1-11148 MA-1535 SERIES PLU Table Programming (Submode 4)-------------------------------------------------------------- 4-14 Time Setting or Adjustment (Submode 5)----------------------------------------------------------- 4-17 Date Setting or Adjustment (Submode 6) ----------------------------------------------------------- 4-18 4.10 Department Group Name Programming (Submode 13)----------------------------------------- 4-18 4.11 Link-PLU Table Programming (Submode 25)------------------------------------------------------ 4-19 4.12 PLU Preset-Code Key Setting (Submode 27) ----------------------------------------------------- 4-20 4.13 PLU Group Programming (Submode 29) ----------------------------------------------------------- 4-20...
1. DAILLY OPERATION FLOW EO1-11148 1. DAILY OPERATION FLOW 1. DAILY OPERATION FLOW The following shows the typical flow of daily operations on the ECR. CASHIER’S OPERATIONS MANAGER’S OPERATIONS OR ASSISTANCE (described in OPERATOR’S GUIDE) (described in MANAGER’S GUIDE) Sign-ON No-sale Receipt (to check the print condition (Adjust the date and time, if necessary.
2. OPERATIONS IN [−] MODE EO1-11148 2. OPERATIONS IN [−] MODE 2. OPERATIONS IN [−] MODE This chapter describes operations to be performed in the “[-]” position of the Control Lock, which the Store Owner or a person so authorized can access using the MA key. Instead of using the [RTN MDSE] or [VOID] key in the “REG”...
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3. READ (X) AND RESET (Z) REPORTS 3. READ (X) AND RESET (Z) REPORTS WARNING! When opening the cash drawer, be careful not to let the drawer hit any person. The following table shows the key operation to take each report. The X and Z reports have basically the same print content if both are available, except that: The Read (X) report allows reading the totals without clearing the memory.
Page 58
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3. READ (X) AND RESET (Z) REPORTS Sample Control Report Name Key Operation Page Lock PLU READ AND RESET All PLU Read 13 [AT/TL] 3-19 All PLU Reset PLU Group Sales Read |PLU Group No.| [#/NS] 13 [AT/TL] 3-20 Zone PLU Read...
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.1 Money Declaration 3.1 Money Declaration When the Money Declaration feature is selected, each cashier who has operated the register on the day must end with his/her Money Declaration operation. Without performing this, the Daily Financial Report cannot be taken.
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3 Report Samples 3.3.1 Financial Read or Reset (Daily) OPERATION Control Lock: X for read, Z for reset 03 [AT/TL] NOTES: 1. Printing will be cancelled by depressing the [C] key during report print. 2.
Page 63
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples Daily Report EU Balance Date, Register No. 15-11-2001 #1234 Report Type Symbol ************************ Report Title FINANCIAL REPORT ************************ Reset Count of this Reset Report (printed on Reset Report only) Z1:0004 Grand Total (non-resettable) 10039.26...
Page 64
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples Daily Report EU Balance (Cont.) LOAN 0000 Loan: Count 0.00 Amount PICK UP 0000 Pick Up: Count 0.00 Amount CASH ID 50172.10 Cash-in-drawer Amount CHECK ID 135.00 Check-in-drawer Amount CHARGE ID 120.00 Charge-in-drawer Amount...
Page 65
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples Daily Report EU Balance (Cont.) Memory Balance GS (Gross Sale) = (Sum of Positive Depts) + (Sum of Taxes) Net Sale with Tax = All Media Sales = (Gross Sale)-(Negative Depts) – (Negative HASH Depts)+ (Positive HASH Depts)+(%+) - (%- on Line Items) –...
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.2 Financial Read or Reset (GT) OPERATION Control Lock: X for read, Z for reset 203 [AT/TL] NOTE: Printing will be cancelled by depressing the [C] key during report print. GT Report US Balance Date, Register No.
Page 68
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples GT Report US Balance (Cont.) NS w/o TAX 0.00 NET Sale without TAX: EX CUS 0000 Tax Exempt Count TAX EX 1 0.00 Tax 1 Exempt Amount TAX EX 2 0.00 Tax 2 Exempt Amount TAX EX 3...
Page 69
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples GT Report EU Balance 15-11-2001 #1234 Date, Register No. Report Type Symbol ************************ FINANCIAL REPORT Report Title ************************ Z2:0004 Reset Count of this Reset Report (printed on Reset Report only) 10039.26 Grand Total (non-resettable) NET GT...
Page 70
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples GT Report EU Balance (Cont.) LOAN 0000 Loan: Count 0.00 Amount PICK UP 0000 Pick Up: Count Amount 0.00 CASH ID 50172.10 Cash-in-drawer Amount CHECK ID 135.00 Check-in-drawer Amount Charge-in-drawer Amount CHARGE ID 120.00...
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.3 Department Report OPERATION Control Lock: X for read, Z for reset 11 [AT/TL] NOTES: 1. Printing will be cancelled by depressing the [C] key during report print. 2. Department data without department group setting will be printed first, followed by the Departments with Department Group Number.
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.4 Zone Department Report OPERATION Control Lock: X ⏐Zone start department No.⏐ [#/NS] ⏐Zone end department No.⏐ [#/NS] 11 [AT/TL] NOTES: 1. Department No.: 01 - 99 2. Printing will be cancelled by depressing the [C] key during report print. 3.
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.5 Accumulated Department Report OPERATION Control Lock: X for read, Z for reset 211 [AT/TL] NOTES: 1. Printing will be cancelled by depressing the [C] key during report print. 2.
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.6 Zone Accumulated Department Report OPERATION Control Lock: X ⏐Zone start department No.⏐ [#/NS] ⏐Zone end department No.⏐ [#/NS] 211 [AT/TL] NOTES: 1. Department No.: 01 – 99 2. Printing will be cancelled by depressing the [C] key during report print. 3.
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.7 PLU Report OPERATION Control Lock: X for read, Z for reset 13 [AT/TL] NOTE: Printing will be cancelled by depressing the [C] key during report print. When Department and PLU Sales Ratio on When Department and PLU Sales Ratio on Reports is NOT programmed in Print Item on Reports is programmed in Print Item on...
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.8 PLU Group Report OPERATION Control Lock: X ⏐Group code⏐ [#/NS] 13 [AT/TL] NOTES: 1. Group Code: 01-99 2. Printing will be cancelled by depressing the [C] key during report print. When Department and PLU Sales Ratio on When Department and PLU Sales Ratio on Reports is NOT programmed in Print Item on...
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.9 Zone PLU Report OPERATION Control Lock: X ⏐Zone start PLU No.⏐ [#/NS] ⏐Zone end PLU No.⏐ [#/NS] 13 [AT/TL] NOTES: 1. When the entered zone start/end PLU No. does not exist, the ECR will find the next PLU 2.
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.10 Accumulated PLU Report OPERATION Control Lock: X for read, Z for reset 213 [AT/TL] NOTES: 1. Printing will be cancelled by depressing the [C] key during report print. 2.
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.11 Accumulated PLU Group Report OPERATION Control Lock: X ⏐Group code⏐ [#/NS] 213 [AT/TL] NOTES: 1. Group Code: 01 to 99 2. Printing will be cancelled by depressing the [C] key during report print. 3.
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.12 Zone Accumulated PLU Report OPERATION Control Lock: X ⏐Zone start PLU No.⏐ [#/NS] ⏐Zone end PLU No.⏐ [#/NS] 213 [AT/TL] NOTES: 1. When entered Zone start/end PLU No. does not exist, the ECR will find the next PLU No. 2.
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.13 PLU Cashier Sales Report OPERATION Control Lock: X for read, Z for reset 07 [AT/TL] NOTE: Printing will be cancelled by depressing the [C] key during report print. CL21 15-11-2001 #1234...
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.14 Cashier Report OPERATION Control Lock: X for read, Z for reset 04 [AT/TL] NOTE: Printing will be cancelled by depressing the [C] key during report print . US Balance CREDIT-2 0001 2.00...
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.18 Hourly Report OPERATION Control Lock: X for read, Z for reset 10 [AT/TL] NOTE: Printing will be cancelled by depressing the [C] key during report print . 15-11-2001 #1234 ************************ HOURLY REPORT...
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.19 Media in Drawer OPERATION Control Lock: X 12 [AT/TL] NOTE: Printing will be cancelled by depressing the [C] key during report print . 15-11-2001 #1234 ************************ MEDIA IN DRAWER ************************ MEDIA TL 0000...
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.21 DP and Financial Read or Reset OPERATION Control Lock: X for read, Z for reset [AT/TL] NOTES: 1. Printing will be cancelled by depressing the [C] key during report print. 2.
Page 90
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples EU Balance When Department and PLU Sales Ratio on When Department and PLU Sales Ratio on Reports is NOT programmed in Print Item on Reports is programmed in Print Item on Reports Setting Reports Setting 15-11-2001...
Page 91
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples EU Balance (Cont.) 10039.26 CREDIT-1 ID 1.00 NET GT 988.94 CREDIT-2 ID 2.00 NEG-GT 0.00 CREDIT-3 ID 3.00 Financial Report 1035.00 CASH DIF 50172.10 NS w/o Tax 1000.00 CHECK DIF 135.00 TAX 1 2.00...
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples 3.3.22 DP and Financial GT Read and GT Reset OPERATION Control Lock: X for read, Z for reset 200 [AT/TL] NOTES: 1. Printing will be cancelled by depressing the [C] key during report print. 2.
Page 94
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples EU Balance When Department and PLU Sales Ratio on When Department and PLU Sales Ratio on Reports is NOT programmed in Print Item on Reports is programmed in Print Item on Reports Setting Reports Setting 15-11-2001...
Page 95
3. READ (X) AND RESET (Z) REPORTS EO1-11148 3.3 Report Samples EU Balance (Cont.) 10039.26 CREDIT-1 ID 1.00 NET GT 988.94 CREDIT-2 ID 2.00 NEG-GT 0.00 CREDIT-3 ID 3.00 Financial Report 1035.00 CASH DIF 50172.10 NS w/o Tax 1000.00 CHECK DIF 135.00 TAX 1 2.00...
This chapter is provided for the store programmer or the store manager who may have to change the programmed data of the MA-1535 series ECR on the daily, weekly, or monthly basis. Usually, all the basic program data required for your store should be set before delivering the product by your local TOSHIBA TEC representative.
4. PROGRAMMING OPERATIONS EO1-11148 4.1 Basic Key Functions 4.1 Basic Key Functions 1) Main keys [#/NS] ----------------- Used to enter the Program Submode No., Address data, Item data. Used to end the entire Program Submode Sequence. [ST], [AT/TL]-------- Used to enter the Address No., Item Code. Used to end the Item data entries.
4. PROGRAMMING OPERATIONS EO1-11148 4.2 Character Entry Method 4.2 Character Entry Method Character Entry Method is to set characters by entering Character Code. This method is allowed on the ECR keyboard. 4- 3...
Page 99
4. PROGRAMMING OPERATIONS EO1-11148 4.2 Character Entry Method Character Setting Operation Key layout required at character setting is shown below. (Keys of bold characters are used at programming operation.) #/NS SPACE C (Clear) AT/TL As character entry method, the Character Codes shown on the previous page are used basically. The above shadowed keys are used for character code entry.
4. PROGRAMMING OPERATIONS EO1-11148 4.3 Condition Required for Programming Operations 4.3 Condition Required for Programming Operations “CONDITION” is given at the top of each programming operation. The ECR must satisfy this condition to perform programming operations. There are two types of conditions: “Any time outside a sale”...
4. PROGRAMMING OPERATIONS EO1-11148 4.4 Store Message and Commercial Message Programming (Submode 1) 4.4 Store Message and Commercial Message Programming (Submode 1) Store Message and Commercial Message to be printed as receipt header can be programmed here. Anytime outside a sale CONDITION OPERATION Control Lock: SET...
Page 102
4. PROGRAMMING OPERATIONS EO1-11148 4.4 Store Message and Commercial Message Programming (Submode 1) Key Operation: Control Lock: SET, Enter 01 and depress the [#/NS] key. 01 [#/NS] (Line No. 1) [2] [0] (Space) [2] [0] (Space) [3] [7] [2] [0] (Space) [3] [a] [2] [0]...
4. PROGRAMMING OPERATIONS EO1-11148 4.5 Cashier Code and Name Programming (Submode 2) 4.5 Cashier Code and Name Programming (Submode 2) CONDITION Anytime outside a sale OPERATION Control Lock: SET Repeat for other cashiers. 02 [#/NS] |Cashier Code| [#/NS] 2 digits (01 to 99) 01: Cashier Name Character entry [AT/TL]...
Page 104
4. PROGRAMMING OPERATIONS EO1-11148 4.5 Cashier Code and Name Programming (Submode 2) *HALO/LALO (This setting will be effective as amount limit at the payment.) HALO (High Amount to be Locked Out) LALO (Low Amount to be Locked Out) 0: No limit 0: No limit 1: 1 digit (0 to 9) 1: 1 digit (1 to 9999999)
Page 105
4. PROGRAMMING OPERATIONS EO1-11148 4.5 Cashier Code and Name Programming (Submode 2) Example) To program the following cashier data Cashier Code: Cashier Name: Jones Pass Code: HALO/LALO: No limit/No limit Commission Rate: 0.5% Commission Amount: (Net sale without Tax) x (Commission Rate) Cashier prohibited item: Returned Merchandise operation Cashier Status:...
4. PROGRAMMING OPERATIONS EO1-11148 4.6 Department Table Programming (Submode 3) 4.6 Department Table Programming (Submode 3) CONDITION To change the positive/negative status: After all Department reset To change any other programmed data or to newly program departments: Anytime outside a sale Control Lock: SET OPERATION Repeat for other departments.
Page 107
4. PROGRAMMING OPERATIONS EO1-11148 4.6 Department Table Programming (Submode 3) NOTES: 1. In each item setting, depressing the [AT/TL] key without data entry skips to the next item setting. 2. Entering 2 digits of numeric code provides an alphanumeric character of Department Name.
Page 108
4. PROGRAMMING OPERATIONS EO1-11148 4.6 Department Table Programming (Submode 3) Example) To program the following department data Department Code: Department Name: VEGETABLE Preset Price: Open Tax Status: Tax 1 taxable (QP balance) Tax 1 taxable and Foot Stamp (US balance) Department Group No.: HALO/LALO: No limit/No limit...
4. PROGRAMMING OPERATIONS EO1-11148 4.7 PLU Table Programming (Submode 4) 4.7 PLU Table Programming (Submode 4) To program new PLUs or to change any programmed contents of PLUs except the CONDITION following case: Anytime outside a sale To change the linked Department of a PLU with sales data not zero: After PLU Reset OPERATION Control Lock: SET Repeat for other PLUs.
Page 110
4. PROGRAMMING OPERATIONS EO1-11148 4.7 PLU Table Programming (Submode 4) NOTES: 1. In each item setting, depressing the [AT/TL] key without data entry skips to the next item setting. 2. Up to 24,000 PLUs are programmable. (The Number of PLU varies depending on the capacity and allocation of the RAM.) 3.
Page 111
4. PROGRAMMING OPERATIONS EO1-11148 4.7 PLU Table Programming (Submode 4) Example) QP balance To program the following PLU data PLU Code: 1000000010101 PLU Name: Tomato STORE Preset Price: 1.00 1343 PEACH DRIVE PHONE: 87-6437 2nd Preset Price: 1.20 Open 8:00am to 7:00pm 3rd Preset Price: 1.40 Closed: every Wednesday...
4. PROGRAMMING OPERATIONS EO1-11148 4.8 Time Setting or Adjustment (Submode 5) Deletion After PLU reset CONDITION OPERATION Control Lock: SET 04 [#/NS] [VOID] |PLU Code| [#/NS] [#/NS] Max. 13digits |Source Code or In-Store Code| [X/TIME] Barcode Scanning Example) To delete PLU No. 1000000090101 (Coke Small-A) that was programmed. Key Operation: Control Lock: SET, Enter 04 and depress the [#/NS] key.
(01 to 31) (01 to 12) (00 to 99) NOTE: The date entry order may be Month-Day-Year or Year-Month-Day instead of Day-Month-Year by programmable option. For details, please contact your TOSHIBA TEC representative. Example) To set date “January 24, 2002”. STORE 1343 PEACH DRIVE Key Operation: Control Lock: SET, Enter 06 and depress the [#/NS] key.
1. If “0” is entered as PLU code in the above sequence, the KEY is reset. 2. The [KEY] in the above sequence should be set beforehand. For details, please contact your TOSHIBA TEC representative. Example) To program the following PLU Codes to required KEYs on the ECR Keyboard. Key Operation: Control Lock: SET Enter 27, depress the [#/NS] key.
Page 116
4. PROGRAMMING OPERATIONS EO1-11148 4.13 PLU Group Programming (Submode 29) Example) To program the following names to respective Groups. G R O C E R Y P L U PLU Group 1 PLU Group 2 G R O C E R Y P L U Key Operation: Control Lock: SET, Enter 29 and depress the [#/NS] key.
4. PROGRAMMING OPERATIONS EO1-11148 4.14 Footer Message Programming (Submode 31) 4.14 Footer Message Programming (Submode 31) A Footer message (max. 120 characters; 24 characters x 5 lines) to be printed on the footer portion of receipt can be programmed here. Anytime outside a sale CONDITION Control Lock: SET...
3. None of [FUNCTION] keys themselves can be contained in a string of keys for any [FUNCTION] key. 4. The [FUNCTION] key should be set beforehand. For details, please contact your TOSHIBA TEC representative. Example) To set the following key operation as [FUNCTION 1] key: STORE 1343 PEACH DRIVE...
4. PROGRAMMING OPERATIONS EO1-11148 4.17 %+ and %- Preset Rate Setting (Submode 36) 4.17 %+ and %- Preset Rate Setting (Submode 36) A Preset Rate can be set on each of the [%+] and [%-] keys, one independent rate for each key. Once a rate is preset, the % key will simply be depressed without a prior rate entry to activate the preset rate.
4. PROGRAMMING OPERATIONS EO1-11148 4.18 Foreign Currency Exchange Rate Setting (Submode 37) 4.18 Foreign Currency Exchange Rate Setting (Submode 37) The rate of each Foreign Currency (corresponding to the [CUR1] to [CUR3] keys; QP balance, [CUR1] to [CUR4] keys; US balance) can be set here. By setting a rate on each Foreign Currency Key, reading the sale total and tendering in the foreign currency value will be possible for sale finalization.
4. PROGRAMMING OPERATIONS EO1-11148 4.19 + (Amount Charge) and – (Amount Discount) Preset Setting (Submode 38) 4.19 + (Amount Charge) and – (Amount Discount) Preset Setting (Submode 38) A Preset Amount can be set on each of the [+] and [-] keys, one independent amount for each key. Once an amount is preset, these keys will simply be depressed without a prior amount entry to activate the preset amount.
4. PROGRAMMING OPERATIONS EO1-11148 4.21 Register No. Setting (Submode 43) 4.21 Register No. Setting (Submode 43) 4-digit numbers can be set as Register ID No. Once set, it will be printed on journal and every receipt. Anytime outside a sale CONDITION Control Lock: SET OPERATION...
5. PROGRAMMED DATA VERIFICATION EO1-11148 5. PROGRAMMED DATA VERIFICATION 5. PROGRAMMED DATA VERIFICATION Whenever programming operations are performed, it is recommended to issue Program Verification receipts to check the programmed data before entering any other operation. The print format of each program reading is almost the same as that of the program receipt.
Page 125
5. PROGRAMMED DATA VERIFICATION EO1-11148 5. PROGRAMMED DATA VERIFICATION 3) Individual PLU Group Read • X mode 90 [AT/TL] 03 [#/NS] |PLU Group Code| [AT/TL] [#/NS] 2 digits (01 to 99) • SET mode 90 [#/NS] 03 [#/NS] |PLU Group Code| [AT/TL] [#/NS] 2 digits (01 to 99) NOTE: Printing will be cancelled by depressing the [C] key during report print.
Page 126
5. PROGRAMMED DATA VERIFICATION EO1-11148 5. PROGRAMMED DATA VERIFICATION 4) Zone Department Read • X mode 90 [AT/TL] 04 [#/NS] |Zone-start Department Code| [X/TIME] |Zone-end Department Code| [AT/TL] [#/NS] • SET mode 90 [#/NS] 04 [#/NS] |Zone-start Department Code| [X/TIME] |Zone-end Department Code| [AT/TL] [#/NS] NOTE: Printing will be cancelled by depressing the [C] key during report print.
Page 127
5. PROGRAMMED DATA VERIFICATION EO1-11148 5. PROGRAMMED DATA VERIFICATION 5) Simple PLU Read In this operation, the following 5 items (PLU Code, PLU Name, Unit Price 1, Unit Price 2, and Unit Price 3) extracted from the PLU read report will be printed out. •...
Page 128
5. PROGRAMMED DATA VERIFICATION EO1-11148 5. PROGRAMMED DATA VERIFICATION 6) Simple Zone PLU Read • X mode 90 [AT/TL] 06 [#/NS] |Zone-start PLU Code| [X/TIME] |Zone-end PLU Code| [AT/TL] [#/NS] 13 digits 13 digits • SET mode 90 [#/NS] 06 [#/NS] |Zone-start PLU Code| [X/TIME] |Zone-end PLU Code| [AT/TL] [#/NS] 13 digits...
Page 129
English Waste Recycling information for users: Following information is only for EU-member states: The crossed out wheeled bin symbol is used to indicate that the product must not be treated as general household waste. By ensuring that this product is disposed of correctly you will be helping to prevent potentially negative consequences for the environment and human health, which could otherwise be caused by incorrect waste handling of this product.