Dv Automatic Recording (Dv Auto Rec) - Panasonic DMR-HS2 Operating Instructions Manual

[HDD] [RAM]
Preparation
≥Before connecting any cables, first make sure that the power for
both units is off.
Then after connecting any cable, turn on the both units.
≥Connect the DV equipment to the DV input terminal on the front
panel.
≥Pause play of the DV equipment at the point you want recording
to start.
≥Switch [DVD, TV] (15) to "DVD".
≥Recording to the HDD:
Confirm there is sufficient empty space for recording on the
HDD. (page 26)
Recording to the disc:
Insert a disc that can be written to.
- Check that disc can be recorded on (page 10).
- Ensure the write protect tab is not set to "PROTECT"
(page 87).
- Ensure the disc is not write-protected with DISC
INFORMATION (page 39).
Press [HDD] or [DVD] (6) to select the recording
1
drive.
(page 18)
2 Press [REC MODE] (26) to select the recording
mode.
≥Select "XP", "SP", "LP", or "EP".
3
While stopped
Press [FUNCTIONS] (11)
4 Use [3, 4, 2, 1]
(10)
and press [ENTER] (10)
≥The DV equipment pauses automatically if it was playing.
DV AUTO REC
Use [2, 1]
5 (10)
to select "Rec" and press [ENTER]
(10)
.
≥Recording starts.
DV AUTO REC
Model of DV Panasonic
NV-
Remain 01:04(SP)
Rec Cancel
RETURN
ENTER
To stop recording manually
Press [∫] (7).

DV Automatic Recording (DV AUTO REC)

(1)
(2)
.
to select "DV AUTO REC"
.
ªWhen recording stops
The following screen appears.
DV AUTO REC
Recording finished.
ENTER RETURN
Press [ENTER] (10) to finish DV auto recording.
≥A programme and play list is added when DV auto recording
finishes.
For your reference
≥Do not operate the DV equipment during recording, as this will
cause recording to stop.
One recording session (from where recording is started to where
it is stopped) is counted as one programme and a play list is
automatically created. You can divide the recording into scenes
by detecting the parts that the recording button of the DV
equipment is pressed during recording of the DV equipment. The
date of the first recording is used as the programme's title.
≥The marker is automatically registered by detecting the parts that
the recording button of the DV equipment is pressed during
recording of the DV equipment.
≥Make sure the DV equipment is paused before starting recording.
If recording cannot start (the DV equipment is not connected
correctly or a tape isn't loaded) or cannot continue, the screen
shows a warning message and cancels recording. Check the
equipment carefully before trying to record from it.
≥The DV equipment name may not be shown correctly.
≥You cannot record and play simultaneously.
≥You cannot start recording until the images from the DV
equipment appear on the television.
≥The audio recorded is the audio selected at "Audio Mode for DV
Input" (page 74).
≥We recommend using Panasonic digital video camera.
≥Recording may not be performed as desired if the time codes on
the tape in the DV equipment are not successive.
≥We recommend connecting one piece of DV equipment at a time.
≥Even if you use device equipped with DV Terminals, you may not
be able to perform DV auto recording in some cases.
Note
≥You cannot control this unit from the digital video equipment even
if using the DV cable.
≥This unit does not support recording the signal from a personal
computer.
≥The DV input on this unit is for use with DV cameras only.
≥Select the TV system (PAL/NTSC) of the programme you wish to
record (page 75).
67