Page 1
ORDER NO.DSD0405014C8 DVD Video Recorder DMR-E85HEP Colour (S).......Silver Type SPECIFICATIONS...
Page 2
2004 Matsushita Electric Industrial CO., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. Safety precautions 1.1. General guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit.
Page 3
2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed. 3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards. 1.1.1.
Page 4
6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 milliampere. In case a measurement isoutside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.
Page 5
comparableconductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Caution Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
Page 6
4.1. About lead free solder (PbF) Distinction of PbF P.C.B.: P.C.B.s (manufactured) using lead free solder will have a PbF stamp on the P.C.B. Caution: - Pb free solder has a higher melting point than standard solder; Typically the melting point is 50 - 70°F (30 - 40°C) higher. Please use a high temperature soldering iron.
Page 7
5. Take out the disc and put the Opener Roller on fully position for direction of Arrow. 6. Put the Upper Base Unit so that the Opener Roller is inserted into the groove. 7. Check center of Opener Roller is seen through the Opener position Checking Hole, and tighten 4 screws.
Page 8
*After finishing display “(7). Factor of Drive Error occurring”, press [0] [2] ~[9] [9] keys of the Remote Controller so that 99 memories can be displayed as maximum. 2. Press [4] [2] keys of remote controller. Example of FL Display: (1) Error Number is displayed for 5 seconds.
Page 9
FL Display (Disc Disc Maker Country Maker's ID) Panasonic Japan Pioneer Japan Mitsubishi Chemical Japan Corporation Japan Maxell Japan MITUI CHEMICALS Japan Victor JVC Japan TAIYOYUDEN Taiyo yuden Japan Giga Storage Taiwan PRODISC Prodisc Taiwan PRINCO PRINCO Taiwan RITEK RITEK...
Page 10
FL Display Disc Type DVD-ROM/Video Audio-CD 2.6GB DVD-RAM 4.7GB DVD-RAM DVD-R Error Occurring Disc State 8. Self-Diagnosis and Special Mode Setting 8.1. Self-Diagnosis Functions Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred. U14, H** and F** are stored in memory and held.
Page 11
Error Diagnosis contents Description Monitor FL display Display Code Remote control code Display appears when main unit No display error and remote controller codes are not matched. “*” is remote controller code of the main Display for 5 seconds. Abnormal inner Display appears when the drive No display temperature detected...
Page 12
Error Diagnosis contents Description Monitor FL display Display Code Unsupported disc *An unsupported format disc “This disc is UNSUPPORT error was played, although the drive incompatible.” starts normally. *The data format is not Display for 5 seconds. supported, although the media type is supported.
Page 13
Item FL display Key operation Mode name Description Front Key TEST Mode *All the main unit's parameters Press [SKIP (REV)], (include tuner) are initialized. SLIP] and [OPEN keys simultaneously five seconds when is off. Service Mode Setting every kind of modes for When the power servicing.
Page 14
Item FL display Key operation Mode name Description Front Key Aging Perform sequence of modes as * Display following the then When the power Aging Description shown below mode. press [CH DOWN], continually. SLIP] and [OPEN CLOSE] simultaneously for over five seconds less than 10 seconds.
Page 15
Item FL display Key operation Mode name Description Front Key Progressive The progressive setting is The display before When the power initialization initialized to Interlace. execution leaves. E mode), press [ and [TIME SLIP] simultaneously seconds. Aging Contents (Example): 8.3. Service Modes Service mode setting: While the power is off, press TIME SLIP, STOP and OPEN / CLOSE simultaneously for five seconds.
Page 16
Item FL display Key operation Mode name Description (Remote controller ROM Version Region code, MAIN firm version, Press [0] [2] in service Display TIMER firm version and DRIVE mode firmware versions are displayed on FL for five seconds per each version in order, but ROM version will be left displayed.
Page 17
Item FL display Key operation Mode name Description (Remote controller White Picture White picture is output as *Initial mode is “Interlace”. Press [1] [1] in service Output component Output from AV mode. Decoder. *White picture (Saturation rate : 100%) Switch Interlace/ Press [1] [4] in White *It is enable to switch Interlace/ Progressive...
Page 18
Item FL display Key operation Mode name Description (Remote controller Magenta Picture Magenta picture is output with *Initial mode is “Interlace”. Press [1] [2] in service Output Component Output from AV mode. Decoder. *Magenta picture (Saturation rate: 100%) Switch Interlace/ Press [1] [4] in Magenta *It is enable to switch Interlace/ Progressive...
Page 19
Item FL display Key operation Mode name Description (Remote controller Audio Pattern The audio pattern stored in the Initial mode (Audio 48kHz) Press [2] [3] in service Output internal memory is output mode. (Lch: 1kHz/-18dB) (Rch: 400Hz/-18dB) Audio 44.1kHz/48kHz Press [2] [4] in Audio *Audio sound clock switching switching Pattern Output mode.
Page 20
Item FL display Key operation Mode name Description (Remote controller RAM Drive Last RAM Drive error code display. 1. Error Number is Press [4] [2] in service Error displayed for 5 seconds. mode. *For details about the drive error code, refer to the Service Manual Then press [0] [1] for the specific RAM Drive.
Page 21
Item FL display Key operation Mode name Description (Remote controller Delete the Last Delete the Last Drive Error Press [9] [6] in service Drive Error information stored on the DVD mode. RAM-Drive. Turn on all FL/ All segments of FL and all LEDs All segments are turned Press [5] [1] in service LEDs...
Page 22
Item FL display Key operation Mode name Description (Remote controller Display the Error Display the Error History stored Display reason of error for Press [6] [5] in service History on the unit. 5 seconds. mode. Then press [0] [1] the past 19 error are displayed.
Page 23
Item FL display Key operation Mode name Description (Remote controller P50 (H) Output Timer Microprocessor IC7501-22 Press [8] [4] in service output High signal for AV1-pin 10 mode. passing through inverter (approx. 0V DC at AV1-pin 10). When OK. When NG. P50 (L) Output Timer Microprocessor IC7501-22 Press [8] [5] in service...
Page 24
The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing. To assemble the unit, reverse the steps shown in the chart below. 9.2. P.C.B. Positions 9.3. Top Case 1. Remove the 2 screws (A) and 3 screws (B). 2.
Page 25
9.4. Digital P.C.B. 1. Remove the FFC and a Screw. 2. Unlock a Rocking Spacer. 3. Lift up Digital P.C.B. slightly so to disconnect Connector to remove Digital P.C.B. CAUTION: When replacing Digital P.C.B., pay attention as below.
Page 26
9.5. Front Panel 1. Remove 3 tabs (A) and 2 tabs (B) in this order. (The tab (A) and (B) should be removed at the same time, respectively.) 2. Move the front panel to front side straight and slowly so to remove it with Connector.
Page 27
9.6. Front (R) P.C.B. 1. Remove 6 screws and Front Angle. 9.7. HDD 1. Remove 3 Screws (A) and 2 connectors. 2. Slide and lift up HDD Holder in the direction of the arrows so to unlock 3 locking tabs.
Page 28
3. Lift up HDD with super sheet vertically and remove super sheet. Handling of HDD The following precautions should be taken when handling HDD. 1. Never give an impact to HDD. (Even a drop from 1cm height can be a cause of HDD failure.
Page 29
9.8. HDD Bracket 1. Remove 4 screws (B) and HDD Bracket with 2 Insulation Sheets. 9.9. DVD-RAM Drive 1. Remove 3 Screws. 2. Pull out DVD-RAM Drive vertically so to remove it with Connector. 9.10. Rear Panel 1. Remove the 12 screws (A) and screw (B). 2.
Page 30
9.10.1. Only Fan Motor 1. Remove the 2 screws. 2. Remove Fan Connector to remove Fan Motor. 9.11. Main P.C.B. 1. Remove the 7 screws (A), Connector (A) and Fan Connector.
Page 31
2. Remove a Screw (B) and lift up Front Jack portion of Main P.C.B. slightly so to unlock Tab to remove Main P.C.B.. 9.12. Power P.C.B. 1. Lift up Power P.C.B. a little so to unlock 2 Tabs and slide Power P.C.B.
Page 32
9.13. The Scart P.C.B. 1. Pull out the Scart P.C.B. in the direction of the arrow. Note: At first disconnect the connector on one side, and pull out the Scart P.C.B. 9.14. VIF Decoder P.C.B. and Nicam Decoder P.C.B. 1. Remove the solders. 2.
Page 33
10. Service Fixture and Tools Part Number Description Compatibility RFKZ0125 Extension FFC (Digital P.C.B. - DVD-RAM Drive / 40 Pin) Same as E50 series RFKZ0168 Extension Cable (Main P.C.B. - Fan / 3 Pin) Same as E50 series RFKZ0169 Extension Cable (Power P.C.B. - HDD / 4 Pin) Same as E100H series RFKZ0197 Extension Cable (Main P.C.B.
Page 34
11. Service Positions Note: For description of the disassembling procedure, see the section 9. 11.1. Checking and Repairing of Power P.C.B.
Page 35
11.2. Checking and Repairing of Main P.C.B.
Page 36
11.3. Checking and Repairing of Digital P.C.B.
Page 37
11.4. Checking and Repairing of DVD-RAM Drive...
Page 39
12. Adjustment Procedures 12.1. After replacing the RAM Drive with new one 12.2. When the unit does not operate normally after replacing the Timer Microprocessor with new one in order to transmit the Step Operation Descriptions While power is ON, short IC7508-4 pin (RESET) and “RESET (L)”...
Page 40
Turn on the power, and confirm items pointed Items pointed out should reappear. out. Insert RAM disc. The Panasonic RAM disc should be recognized. Enter the EE (TU IN / AV IN - AV OUT) mode. No abnormality should be seen in the picture, sound or operation.
Item Contents Check Item Contents Block noise Distorted sound Crosscut noise Noise (static, background noise, etc.) Picture Sound Dot noise The sound level is too low. Picture disruption The sound level is too high. Not bright enough The sound level changes. Too bright Flickering color Color fading...
Page 42
INITIAL/LOGO ABBREVIATIONS A0~UP ADDRESS ACLK AUDIO CLOCK AD0~UP ADDRESS BUS ADATA AUDIO PES PACKET DATA ADDRESS LATCH ENABLE AMUTE AUDIO MUTE AREQ AUDIO PES PACKET REQUEST AUDIO RF SERVO AMP INVERTED INPUT SERVO AMPOUTPUT ASYNC AUDIO WORD DISTINCTION SYNC BIT CLOCK (PCM) BCKIN BIT CLOCK INPUT BLACK DROP OUT...
Page 43
INITIAL/LOGO ABBREVIATIONS DACCK D/A CONVERTER CLOCK DEEMP DEEMPHASIS BIT ON/OFF DEMPH DEEMPHASIS SWITCHING DIG0~UP FL DIGIT OUTPUT DATA INPUT DMSRCK DM SERIAL DATA READ CLOCK DMUTE DIGITAL MUTE CONTROL DROP OUT DOUT0~UP DATAOUTPUT DATA SLICE RF (BIAS) DROP OUT SIGNAL DRPOUT DATA REQUEST DREQ...
Page 44
INITIAL/LOGO ABBREVIATIONS IECOUT IEC958 FORMAT DATA OUTPUT IPFRAG INTERPOLATION FLAG IREF I (CURRENT) REFERENCE ISEL INTERFACE MODE SELECT LDON LASER DIODE CONTROL LASER POWER CONTROL LRCK L CH/R CH DISTINCTION CLOCK MA0~UP MEMORY ADDRESS MEMORY CLOCK MCKI MEMORY CLOCK INPUT MCLK MEMORY SERIAL COMMAND CLOCK...
Page 45
INITIAL/LOGO ABBREVIATIONS READ ENABLE RFENV RF ENVELOPE RF PHASE DIFFERENCE OUTPUT (CD-ROM) REGISTER SELECT RSEL RF POLARITY SELECT RESET RESERVE SBI0, 1 SERIAL DATA INPUT SBO0 SERIAL DATA OUTPUT SBT0, 1 SERIAL CLOCK SERIAL DATA CLOCK SCKR AUDIO SERIAL CLOCK RECEIVER SERIAL CLOCK SCLK...
Page 46
SUB CODE Q DATA SYSCLK SYSTEM CLOCK INITIAL/LOGO ABBREVIATIONS TRACKING ERROR TIBAL BALANCE CONTROL BALANCE OUTPUT 1 BALANCE INPUT BALANCE INPUT BALANCE OUTPUT 2 TPSN OP AMP INPUT TPSO OP AMP OUTPUT TPSP OP AMP INVERTED INPUT TRCRS TRACK CROSSSIGNAL TRON TRACKING ON TRSON...
Page 47
INITIAL/LOGO ABBREVIATIONS X' TAL XALE X ADDRESS LATCH ENABLE XAREQ X AUDIO DATA REQUEST XCDROM X CD ROM CHIP SELECT X CHIP SELECT XCSYNC X COMPOSITE SYNC X DATA STROBE XHSYNCO X HORIZONTAL SYNC OUTPUT XHINT XH INTERRUPTREQUEST X' TAL OSCILLATOR INPUT XINT X INTERRUPT X MEMORY WRITE ENABLE...
Page 52
20. Replacement Parts List Notes: *Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc. are used. When replacing any of components, be sure to use only manufactures specified parts shown in the parts list.
Page 81
R7309 R7314 TL7301 LB7302 C7313 C7312 J0JCC0000124 16V10 16V10 C7318 16V10 R7315 C7314 NOTE: DMR-E85HEP DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM Nicam Decoder Schematic Diagram FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 82
DIGITAL P.C.B. Integrated Circuit CKA49 F CKC117 F CKJ33 C CL6729 C LB50001 C FL50006 F R3423 C R4450 F R50003 F RX3520 F RX6728 IC3401 C CKA51 F CKC118 F CKJ34 C CL6730 C LB50002 Capacitor R3427 C R4451 F R50004 F RX3521 F RX6729...
Page 83
Digital P.C.B. OVER VIEW (Component Side) DMR-E85HEP Digital P.C.B. (Component Side) RFKBE85HEP...
Page 84
Digital P.C.B. OVER VIEW (Foil Side) DMR-E85HEP Digital P.C.B. (Foil Side) RFKBE85HEP...
Page 85
Ref.No.6000,50000 SERIES Audio I/O Ref.No.4400 SERIES Sub Power Supply Ref.No.1500 SERIES Main Net Ref.No.7400 SERIES WORKING WORKING Digital P.C.B.connect circuit P7402 Main MEMORY MEMORY DMR-E85HEP BUFFER LOADER P.C.B. 16bit/256M- 16bit/256M- Video I/O Ref.No.3000,3900,4900 SERIES 16bit/64M 16bit/64M SDRAM SDRAM SDRAM SDRAM...
Page 88
NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. (Digital P.C.B.(2/5)) THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Schematic Diagram(EN) DMR-E85HEP AV Encoder Section(Digital P.C.B.(2/5)) Schematic Diagram(EN)
Page 89
Front (R) P.C.B. DMR-E85HEP Front (R) P.C.B. (REP3713B)
Page 90
PLAY SELECT NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN DMR-E85HEP IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Front(R) Schematic Diagram...
Page 92
8 6 4 2 8 6 4 2 CPNCIN DM G CY IN B CB IN R CR IN < D3.3V > BSON ANA 3.3V < ANA3.3V > < ANA5V > ANA 5V < D5V > DMR-E85HEP Glue Net Section(Digital P.C.B.(1/5)) Schematic Diagram(GN)
Page 93
CKJ82 D1.2V < ANA3.3V > < ANA5V > < D5V > DMR-E85HEP Glue Net Section(Digital P.C.B.(1/5)) DMR-E85HEP Schematic Diagram(GN) Glue Net Section(Digital P.C.B.(1/5)) Schematic Diagram(GN) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN...
Page 94
Main Net Ref.No.7400 SERIES MIX R OUT1 MIX R OUT1 Sub Power Supply Ref.No.1500 SERIES Main Video I/O Ref.No.3000 SERIES MIX L OUT1 MIX L OUT1 P.C.B. Audio Main Ref.No.4000 SERIES RESET- Timer Ref.No.7500,7600 SERIES SCART P.C.B. DMR-E85HEP Interconnection Schematic Diagram...
Page 101
R50010 XIRQ0 FL50006 R50011 22K 2400 XSSP F1H0J4740004 R6018 DMR-E85HEP < ANA3.3V > <D3.3V> AV Decoder/Main CPU Section NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS (Digital P.C.B.(4/5)) SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU Schematic Diagram(MC) ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 102
4700 P001 COLD AC SOCKET IMPORTANT SAFETY NOTICE: DMR-E85HEP COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. Main Power Supply NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN WHEN REPLACING ANY OF THESE COMPONENTS.ONLY THE SAME TYPE.
Page 103
IC7301 Ref No. MODE PLAY STOP Ref No. IC7301 MODE PLAY STOP IC7301 Ref No. MODE PLAY STOP IC7302 Ref No. MODE PLAY STOP...
Page 104
D1.2V L7401 V:Video I/O Section(Page: D1.5V D3.3V A:Audio Main Section(Page: IECOUT XDMUTE DMR-E85HEP T:Timer Section(Page: AU 5V MIXLOUT DM Main Net Section MIXROUT DM (Main P.C.B.(2/5)) AADC L NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN AADC R IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 105
Q113 D108 (REG.DR+5V) F103 PC001 125V 2.5A DR+5V PS102 P1502 P1501 P102 FEED (TO DVD RAM DRIVE) BACK 16,17 PS101 TO HDD PS101 Q105 (RESET) COLD PS102 P1502 HDD P-FAIL 5 VDD OUT 4 IC7501- DMR-E85HEP Power Supply Block Diagram...
Page 106
IC3901- IC7403 PS+5V IC3001(+5.0V) (REG.+5V) IC4009/IC4012- REG.+5V PP7401 PS3901 VOUT IC3901- (Audio Main Sec.) QR7401 PS+12V PP7401 PS3901 IC3901- IC7401 (REG.PS+12V) PWR SAVE SCART P.C.B. IC7501- VOUT DMR-E85HEP DMR-E85HEP Power Supply Block Diagram (Main Net Sec.) Power Supply Block Diagram...
Page 110
D3901 R3924 MA2C165001VT <PS+5V> <PS+12V> DMR-E85HEP DMR-E85HEP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN Scart Schematic Diagram Scart Schematic Diagram IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 114
C1543 R1516 C1540 25V47 1000 DMR-E85HEP Sub Power Supply Section (Main P.C.B.(1/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN Schematic Diagram(P) IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 115
QR7501 M:Main Net Section(Page: UNR511300L V:Video I/O Section(Page: (XFWE MUTE) A:Audio Main Section(Page: T:Timer Section(Page: <N SW+5V> <N SW+5V> AV3 IN R AV3 IN L AV3 IN CPS AV3 IN CPNY AV3 IN CPNC DMR-E85HEP Timer Section(Main P.C.B.(5/5)) Schematic Diagram(T)
Page 116
FANDCOUT <N SW+5V> FANLOCK FAN GND DMR-E85HEP DMR-E85HEP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 119
TR MAB6 TR MAB2 TR MAB5 DHDD8 DHDD9 TR MAB3 TR MAB4 DHDD10 DHDD11 VDD33 DMR-E85HEP DMR-E85HEP < D3.3V > Real Time Stream Control(RTSC) Section Real Time Stream Control(RTSC) Section (Digital P.C.B.(3/5)) (Digital P.C.B.(3/5)) < D1.5V > Schematic Diagram(TR) Schematic Diagram(TR) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN...
Page 121
NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. X0702 16V22 J0B4055A0001 NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR DMR-E85HEP ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. VIF Decoder Schematic Diagram...
Page 122
T:Timer Section(Page: Q3007 SCART VIN 2SB1218A0L (AMP) DMR-E85HEP Video I/O Section (Main P.C.B.(3/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN Schematic Diagram(V) IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 123
IC1502 IC1505 IC1506 Ref No. MODE PLAY STOP IC1507 IC1508 IC1509 Ref No. MODE PLAY STOP IC1510 Ref No. MODE PLAY STOP IC3001 Ref No. MODE PLAY STOP IC3001 Ref No. MODE PLAY STOP IC3001 Ref No. MODE PLAY STOP IC3001 Ref No.
Page 124
IC3003 Ref No. MODE PLAY STOP Ref No. IC3003 MODE PLAY STOP Ref No. IC4001 MODE PLAY STOP IC4001 Ref No. MODE PLAY STOP IC4005 IC4007 Ref No. IC4006 MODE PLAY STOP IC4009 IC4010 Ref No. IC4011 MODE 12.1 13.5 12.1 PLAY 12.1...
Page 129
DECODER R DECODER R DD10 DECODER L DECODER L Ref.No. Ref.No.7400 SERIES MIX R OUT1 MIX R OUT1 pply Ref.No.1500 SERIES Ref.No.3000 SERIES MIX L OUT1 MIX L OUT1 Ref.No.4000 SERIES RESET- Ref.No.7500,7600 SERIES SCART P.C.B. DMR-E85HEP Interconnection Schematic Diagram...
Page 131
3.32K 3.32K 1000P 4700 MA165 4700 DMR-E85HEP Main Power Supply USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Schematic Diagram...
Page 132
17.3. Sub Power Supply Section (Main P.C.B. (1/5)) Schematic Diagram (P) C151 10V4 IC1502 C0DBAHG00013 C1516 (REG.JC+5V) IC1506 C0CBCDD00002 (REG.ANA+5V) JC P ON C1519 C1503 C1504 C1505 10V47 POWER ON R1502 D1501 R1503 3300 MA2C165001VT TO P102 RAM DRIVE UNIT P1501 R1501 C1512...
Page 133
X SW 13V X SW 5.8V D3.3V R1515 C1543 DMR-E85HEP Sub Power Supply Section (Main P.C.B.(1/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN Schematic Diagram(P) IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 134
17.4. Main Net Section (Main P.C.B. (2/5)) Schematic Diagram (M) TO PS3901 SCART P.C.B. PP7401 IIC CLK IIC DATA <REG.+5V> BOOSTER+5V <REG.+5V> PS 5V TUNER VIDEO SCART VIDEO IN CPS V OUT CPN Y OUT <REG.PS+12V> <X SW+5.8V> PS 12V LB7407 J0JHC0000032 PR OUT...
Page 135
DECODER AUDIO(L) P:Sub Power Supply Section(Page: M:Main Net Section(Page: V:Video I/O Section(Page: A:Audio Main Section(Page: DMR-E85HEP T:Timer Section(Page: Main Net Section (Main P.C.B.(2/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 137
ZJ3001 K9ZZ00000424 V:Video I/O Section(Page: A:Audio Main Section(Page: T:Timer Section(Page: DMR-E85HEP Video I/O Section (Main P.C.B.(3/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN Schematic Diagram(V) IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 138
17.6. Audio Main Section (Main P.C.B. (4/5)) Schematic Diagram (A) R4022 R4023 R4015 R4021 C4019 16V10 C4031 C4027 C4021 L4002 50V1 50V1 16V10 C4053 C4054 C4022 6V47 LB4001 J0JGC0000020 L2 IN L L2 IN R AADC L AADC R MIXLOUT DM C4069 0.1 MIXROUT DM R4099...
Page 139
A:Audio Main Section(Page: IC4012 T:Timer Section(Page: 4066 C0ABBB000118 (AMP) IN1- IN1+ K4008 DMR-E85HEP 4067 C4070 C4072 10V220 10V220 Audio Main Section (Main P.C.B.(4/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN Schematic Diagram(A) IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 142
(RESET) (FAN MOTOR DRIVE) VOUT NC D7512 B3AEA0000049 C7588 0.01 IC7506 Q7519 C0ABBA000073 2SD601A0L (FAN MOTOR DRIVE) (HDD LED DRIVE) R7672 47K C7546 C7639 R7671 R7602 6800 R7603 R7601 <N SW+5V> DMR-E85HEP NOTE:DO IN THE Timer Section(Main P.C.B.(5/5)) Schematic Diagram(T)
Page 143
FANDCOUT FANLOCK FAN GND DMR-E85HEP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Timer Section(Main P.C.B.(5/5)) Schematic Diagram(T)
Page 147
CKJ78 D1.5V CKJ82 D1.2V DMR-E85HEP Glue Net Section(Digital P.C.B.(1/5)) Schematic Diagram(GN) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 149
BA0S D XWE D RX3416 22X4 DQM0 D XCS0 D GN:Glue Net Section(Page: R3448 XRAS D 5600 XCAS D EN:AV Encoder Section(Page: R3449 6800 TR:RTSC Section(Page: MC:AV Decoder/Main CPU Section(Page: AI:Audio I/O Section(Page: DMR-E85HEP AV Encoder Section(Digital P.C.B.(2/5)) Schematic Diagram(EN)
Page 153
MC:AV Decoder/Main CPU Section(Page: AI:Audio I/O Section(Page: X3437 RX3438 22X4 DMR-E85HEP AV Encoder Section NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. (Digital P.C.B.(2/5)) THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 157
TR MAB8 TR MAB7 TR MAB6 TR MAB5 TR MAB4 DMR-E85HEP Real Time Stream Control(RTSC) Section (Digital P.C.B.(3/5)) Schematic Diagram(TR) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 161
< ANA3.3V > 768FS2 C50001 1 CLK54A1 FL50006 R50011 22K F1H0J4740004 DMR-E85HEP < ANA3.3V > AV Decoder/Main CPU Section (Digital P.C.B.(4/5)) NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU Schematic Diagram(MC) ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 163
GN:Glue Net Section(Page: EN:AV Encoder Section(Page: TR:RTSC Section(Page: MC:AV Decoder/Main CPU Section(Page: AI:Audio I/O Section(Page: DMR-E85HEP Audio I/O Section OWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN (Digital P.C.B.(5/5)) GHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 165
3.3u NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR DMR-E85HEP ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. VIF Decoder Schematic Diagram...
Page 166
17.14. Nicam Decoder Schematic Diagram C7335 C7305 6V100 IC7302 C0EAH0000051 TO PK7701 (RESET) MAIN P.C.B. (MAIN NET) PK7301 TU AUDIO IN LB7303 L7303 J0JCC0000080 G0C1R0JA0019 JC 5V C7303 C7306 C7334 6V100 0.01 50V2.2 C7311 100P R7304 C7301 R7301 C7302 0 TO PK7702 MAIN P.C.B.
Page 167
R7309 R7314 TL7301 LB7302 C7313 C7312 J0JCC0000124 16V10 16V10 C7318 16V10 R7315 C7314 NOTE: DMR-E85HEP DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM Nicam Decoder Schematic Diagram FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 168
17.15. Scart Schematic Diagram LB3922 J0JGC0000020 TO PP7401 MAIN P.C.B. LB3923 J0JGC0000020 (MAIN NET SEC.) PS3901 IIC CLK IIC DATA BOOSTER+5V PS 5V TUNER VIDEO SCART VIDEO IN R3914 150 CPS V OUT R3919 150 CPN Y OUT PS 12V PR OUT PB OUT PY OUT...
Page 171
PAL:576P/576I R3903 R3902 R3901 DMR-E85HEP NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN Scart Schematic Diagram IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 172
17.16. Front (R) Schematic Diagram IR7801 R7802 B3RAD0000071 (REMOTE CON.SENSOR) R7801 C7801 D7801 B3ABA0000109 TIME-WARP QR7801 UNR221400L TIME WARP LED DRIVE TO P7504 MAIN P.C.B. (TIMER SECTION) P7801 KEYIN2 KEYIN3 KEYIN1 TWARP LED K7801 0 HDD SEL LED N SW 5V DVD SEL LED DVD LED R7809 2700...
Page 173
STOP SKIP-R CH-UP TIME-WARP PLAY SELECT E THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN DMR-E85HEP TS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED. Front(R) Schematic Diagram...
Page 176
IC Pin Terminal Chart ( TC 1 - TC 8 ) IC Pin Terminal Chart ( TC9 - TC12 ) IC3404 / AVENC IC3402 / SDRAM IC3501 / RTSC IC50001 / SDRAM IC6001 / AV DEC&MAIN CPU IC6005,IC6006 / W-MEMORY FP3501 (TO DVD RAM&HDD) IC6001 / AV DEC&MAIN CPU SIGNAL NAME...
Page 177
SA0 - SA25 ADDRESS BUS LINE (TC13, TC14-1, TC15-1, TC17, TC18-1, TC20) SD16 - SD31 DATA BUS LINE (TC14-2, TC15-2, TC18-2 ) 14-1 15-1 18-1 14-2 15-2 18-2 IC3404 / AVENC IC6701 / GLUE IC6001 / AVDEC&MAIN CPU IC6004 / BUFFER IC6003 / LOADER IC3501 / RTSC IC6701 / GLUE...
Page 179
L CH IN L OUT IIC DATA FROM IC7501- IIC BUS TIMER LOGIC IIC CLK SECTION IC7501- NICAM DECODER P.C.B. IC4007 IC4005 FROM P9001 P7402 IEC OUT IC4006 DIGITAL OPTICAL P.C.B. D+5V (DIGITAL AUDIO OUT) DMR-E85HEP Analog Audio Block Diagram...
Page 180
MC:AV Decoder/Main CPU Section(Page: XADC PD AUGND AI:Audio I/O Section(Page: DMR-E85HEP Audio I/O Section NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERING. THE CORRECT PART NUMBER IS SHOWN (Digital P.C.B.(5/5)) IN THE PARTS LIST, AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 181
X SW 13V C4026 C4030 C4029 C4059 C4075 C4076 C4077 16V470 16V470 DMR-E85HEP R4067 C4070 C4072 POWER ON 10V220 10V220 Audio Main Section (Main P.C.B.(4/5)) NOTE:DO NOT USE THE PART NUMBER SHOWN ON THIS DRAWING FOR ORDERRING.THE CORRECT PART NUMBER IS SHOWN Schematic Diagram(A) IN THE PARTS LIST,AND MAY BE SLIGHTLY DIFFERNT OR AMENDED SINCE THIS DRAWING WAS PREPARED.
Page 182
AV2 V IN PP7402 PS3902 FROM IC7501- IIC BUS Q7406 TIMER DIGITAL CONTROL IIC CLK SECTION P9001 P7402 R/CR IN P.C.B. BUFFER IC7501- Q7405 P9001 P7402 G/C Y IN BUFFER Q7404 P9001 P7402 B/C B IN BUFFER DMR-E85HEP Analog Video Block Diagram...