Introduction Congratulations for choosing one of the most versatile, fully-featured vehicle secu- rity and convenience systems available today� Omega Research & Development has been a leader in vehicle security products for nearly 4 decades� Please take the time to read this manual thoroughly so you can fully enjoy the benefits and features this system offers�...
Controller & Transmitter Overview THE 2-WAy COnTROLLER Controller part number: 701-03 1) Antenna: Sends commands to the system and receives confirmations for 2-way functions. 2) Touch Screen LCD: Displays all controller func- tion buttons as well as the status of your system� 3) Home Button: This wakes up the controller when the screen is off and returns you back to the status screen�...
Controller & Transmitter Overview (cont’d) THE 1-WAy TRAnSmITTER Transmitter part number: 148-03 “lock” “unlock” button button Call your dealer or visit www.caralarm.com to order replacement “trunk” “start” transmitters. button button Transmitter battery replacement: Remove the small screw from the lower back case, and separate the transmitter halves�...
Page 6
Controller & Transmitter Functions (cont’d) TRUnK RELEASE / CHAnnEL 2: Press and hold the “TRUNK” icon for 3 seconds� • THE SYSTEM WILL DISARM AND THE TRUNK WILL OPEN� • UPON RECEIVINg CONFIRMATION FROM YOUR SYSTEM, THE CONTROLLER WILL PLAY THE TRUNK RELEASE ANIMATION AND VOICE ALERT (1-way transmitter: press anD holD the trunk button for 3 seConDs)
Page 7
Controller & Transmitter Functions (cont’d) SCREEn 2: To access, press the HOME button, tap the screen, press the down arrow once� CHAnnEL 3: Press and hold the “CH3” icon for 3 seconds� • YOUR SYSTEM WILL ACTIVATE THE CHANNEL 3 OUTPUT�...
Page 8
Controller & Transmitter Functions (cont’d) PAnIC: Press and hold the “LOCK” or “UNLOCK” icon for 3 seconds� • THE SIREN/HORN WILL SOUND, THE PARKINg LIgHTS WILL FLASH, AND THE DOORS WILL LOCK OR UNLOCK DEPENDINg WHICH ICON IS PRESSED� (1-way transmitter: press anD holD the loCk or unloCk button for 3 seConDs) SILEnT ARm / DISARm: Press and release the “TRUNK”...
Controller & Transmitter Functions (cont’d) AUXILIARy FUnCTIOnS 1-4: The actual operation of these functions will vary from car to car� They are designed to operate extra vehicle functions like automatic sliding doors or motorized hatches. Aux 1-4 are virtual outputs only available on certain vehicles when this system is integrated with the vehicle’s data network.
Other Remote Start Features (cont’d) PIT-STOP FEATURE This feature allows you to leave your engine running for making quick errands� To use this feature, have the engine running normally from the ignition switch and your foot off the brake pedal. Press the Valet Switch twice; the parking lights will flash and the horn chirps 5 times�...
Security System Features (cont’d) WHEn THE SySTEm TRIGGERS If the system were to be compromised while armed, it will trigger sounding the siren/horn and flashing the parking lights for 30 seconds (programmable). At this point you will also be notified on the controller as to which zone is violated (if in range of the system)�...
Using The Valet Switch (cont’d) REmOTE START VALET mODE, while active, disables remote start� Keyless entry and alarm functions are still operable� To enter remote start valet mode, perform the following steps: STEP 1 - Disarm the system either with the controller or by performing an emergency override and hold the brake pedal�...
Page 13
The Status Light (cont’d) AUTOmATIC TRAnSmITTER VERIFICATIOn (RED LIGHT): Every time you turn on the ignition key, the status light will flash a number of times equal to the number of controllers/transmitters programmed to the system� This unique security feature protects you from a potential thief (valet attendant, mechanic, installer, etc�) from adding their own transmitter without your knowledge and access- ing your vehicle and it’s contents at a later time (the perfect crime!)�...
Multi-Car Operation & Vehicle Profiles mULTI-CAR OPERATIOn The controller can operate up to 2 different systems� When controlling 2 systems, it will receive all status updates on the currently selected vehicle profile and will receive only trigger alerts for the 2nd vehicle� You can switch from one car to the other at any- time as well as choose a unique image and name for each vehicle�...
Programming Controller Options SELECTInG BUTTOn BEEP, mELODy, & VIBRATE mODES The controller has 3 different type of alert modes. BUTTON BEEP configures the controller to beep as a confirmation when you press any icon on the screen. The MELODY and VIBRATE settings configure how you are alerted any time the controller receives a confirmation or alert from the vehicle’s system.
Programming Controller Options (cont’d) SETTInG THE TImE & DATE (cont’d) 4) Now, set the time using the +/- increment icons� You can increase or decrease the minute or hour by increments of 5 or 1� ~Use the gREEN UP ARROW to change from hours to minutes� 5) Press the FOLDER icon to save the date &...
Programming Controller Options (cont’d) SETTInG THE SCREEn On TImE 1) Access SCREEN 5 (see page 16) 2) Press the SCREEN ON TIME icon (see page 16) 3) Choose the 5, 10, or 15 second preset and, if desired, adjust with the +/- 1 second increment icons�...
Anti-Carjacking Protection The system is equipped with three separate Anti-Carjacking protection features (ignition, open door, or by the transmitter)� All three are programmable, and must be turned on to operate� Once activated, the user has 53 seconds to cancel the Anti- Carjacking protection process by pressing the Valet Switch once�...
48 hours after any transmitter programming, including the programming session which was used to turn it on� This feature can only be turned off again by sending the system back to Omega for a reset� Programming Features Step 1 Turn the ignition key “ON”, then “OFF”...
User Programmable Features Feature #1 - SecureCode DEFAULT - 1 Press SecureCode is a unique patented feature which allows you to custom select the num- ber of Valet Switch presses in two stages, instead of a single “1 press”, which would be required in order to perform an Emergency Override�...
Page 21
User Programmable Features (cont’d) Feature #5 - Ignition Activated Override (press “disarm/unlock” button to program) - DEFAULT (press “arm/lock” button to program) This feature allows an activated system to be overridden and disarmed by simply turning the ignition switch on within 10 seconds of the system’s activation� After 10 seconds, the Emergency Override must be performed�...
Page 22
User Programmable Features (cont’d) Feature #11 - Alarm Duration 30 Seconds (press “arm/lock” button to program) - DEFAULT 60 Seconds (press “disarm/unlock” button to program) 90 Seconds (press “trunk” button to program) 120 Seconds (press “start” button to program) This feature allows four choices of the Alarm Duration, which is the period of time for which the system sounding the siren (and/or horn, optionally) and flashes the parking lights when it is triggered�...
User Programmable Features (cont’d) Feature #17 - Ignition Activated Anti-Carjacking Protection (press “disarm/unlock” button to program) - DEFAULT (press “arm/lock” button to program) This form of Anti-Carjacking is initiated by the ignition key being turned on� The Anti- Carjacking protection, and the three ways to initiate it are described on page 18� Feature #18 - Door Activated Anti-Carjacking Protection (press “disarm/unlock”...
Page 24
Installer Programmable Features (cont’d) Feature #2 - Light Relay Functions Dome Light Output (press “arm/lock” button to program) - DEFAULT Door Lock (press “disarm/unlock” button to program) Ignition Output (press “trunk” button to program) Accessory Output (press “start” button to program) The system has two built-in relays, which can be programmed to perform several different functions�...
Page 25
Installer Programmable Features (cont’d) This feature selects the method in which the remote start monitors the engine’s run- ning condition in remote start mode� “Tachless Hi” sensitivity mode has an associated base starter output time duration (see installer feature #5) and monitors the vehicle’s voltage level to determine if the engine is running�...
Page 26
Installer Programmable Features (cont’d) Feature #10 - Gasoline Or Diesel Engine Gasoline (press “arm/lock” button to program) - DEFAULT Diesel (press “disarm/unlock” button to program) This feature changes the system’s timing of the ignition and starter output sequence for remotely starting vehicles with gas or diesel engines� When set for gasoline, the starter output will occur 3 seconds after the ignitions turn on�...
Programmable Features matrix User Feature Programming: Ignition on, off, press valet 5 times # Feature Lock Button Unlock button Trunk button ”START” button 1 SecureCode Enter Stage1 Enter Stage 2 2 Last Door Arming ON w/o Lock ON w/ Lock 3 Automatic Rearming ON w/o Lock ON w/ Lock...
Page 28
Back Cover Color cover is in a separate file.