Table of Contents
Advertisement
Step 2 Using the ignition key, turn the vehicle's ignition switch on.
Step 3 Within 5 seconds press and release the Valet Switch one time. The system
will disarm.
The number of Valet Switch presses which are required for the Emergency
Override is custom-programmable! This is the SecureCode feature, which is
described on page 15 and page 26. The above Emergency Override instructions
reflect the "as received from the factory" default setting.
Remote Panic Feature
Should you feel threatened, or the need to attract attention, you can activate your
system's remote "Panic" feature at any time by pressing and holding for 3 seconds
the controller or transmitter's "arm/lock", the "disarm/unlock", or the "III"
button. Your system will respond by sounding the siren and flashing the parking
lights for the normal activated alarm period of 30 seconds.
Additionally, the Crime Guard system features an unique "enhanced" remote Panic
operation, regarding additional operations during Panic, and in association with the
transmitter button used in it's activation or deactivation:
•
Activating Panic with the "arm/lock" button will lock the doors, arm the
system and engage the starter interrupt.
•
Activating it with the "disarm/unlock" button will unlock the doors, disarm
the system and does not engage the starter interrupt.
•
Activating Panic with the "III" button will not affect the system's armed or
disarmed status; the doors locked or unlock condition; nor will it affect the
starter disable circuit.
To disengage remote Panic, simply press and release any one of the same three
transmitter buttons, or, allow it automatically stop after 30 seconds.
•
Deactivating Panic with the "arm/lock" button will stop Panic, and leave the
system armed with the starter interrupt engaged, and the doors locked.
•
Deactivating it with the "disarm/unlock" button will stop Panic, and leave the
system disarmed with the starter interrupt disengaged, and the doors unlocked.
•
Deactivating Panic with the "III" button will stop Panic, and leave the system
in the same state it was in at the moment Panic started, without locking or
unlocking the doors.
•
If the system is allowed reset itself from remote Panic, it will enter the armed
state, locking the doors and engaging the starter interrupt, regardless of which
of the three buttons was used to activate it.
If desired, it is possible to have the "III" button operate the 3rd channel output or the
two optional further channel outputs, instead of remote Panic- see page 32.
Page - 12
How to Program Features
The vehicle ignition key and the Valet Switch are used to enter the Programming
Mode, then the controller or transmitter is used to change features. Once the system
is in Programming Mode, a 10 second period without programming activity will
cause the system to automatically exit Programming Mode. Features can be
selected in any order as desired.
Enter Programming mode:
Step 1
Turn the vehicles's ignition on.
Step 2
Turn the ignition off.
Step 3
Within 5 seconds, Press & Release the Valet Switch 5 times.
• The siren will chirp then sound briefly and the Status Light will light
steady to confirm that the system is entering Programing Mode.
Access a Feature:
Step 4
Within 10 seconds, Press & Release the Valet Switch the same
number of times as the desired feature's number.
• The siren will chirp and the Status Light will flash off the same number of
times as the Valet Switch was pressed to indicate the feature number
accessed.
Change the Feature:
Step 5
After accessing the desired feature, within 10 seconds Press &
Release the appropriate controller or transmitter button.
• Pressing the "arm/lock" button typically turns the feature on; or sets the
feature's first option. The siren will chirp once when this button is pressed.
• Pressing the "disarm/unlock" button also typically turns the feature off;
or, sets the feature's second option. The siren will chirp twice.
• Many features have third, and even fourth setting options. Pressing the
"II" and "III" buttons select these options. Confirmation chirps when
these buttons are pressed are three and four chirps respectively.
To Access and Change further Features:
Step 6
If there are more features to be programmed, within 10 seconds of
the previous action Press & Release the Valet Switch the same
number of times as the next desired feature's number.
• Again the siren will chirp and the Status Light will flash as many times as
the Valet Switch was pressed to indicate the new feature number which is
now accessed. Then use the controller or transmitter as described in
Step 5 to change the newly accessed feature as desired.
Page - 25
Advertisement
Table of Contents
