Table of Contents
Advertisement
battery warning, you have approximately 10–20 hours of
operation time remaining.
Replacing the Pedal Pod Battery
Do not use a sharp object to remove user-replaceable batteries.
Contact your local waste disposal department to properly
recycle the batteries. Perchlorate Material – special handling
may apply. Go to
www.dtsc.ca.gov/hazardouswaste
/perchlorate.
NOTE: Always replace both batteries at the same time.
1
Locate the circular battery cover
pod.
2
Use a coin
to twist the cover counter-clockwise, moving
the arrow from the locked
3
Remove the cover.
You can use a piece of tape
battery from the cover.
4
Wait 30 seconds.
5
Insert the new battery into the cover, observing polarity.
6
Replace the cover, making sure the arrow points to
unlocked.
7
Use a coin to twist the cover clockwise back into place,
making sure the arrow points to locked.
8
Wait 10 seconds.
After you replace the pedal pod battery, you must set the
installation angle on your Edge
Appendix
Registering Vector
Help us better support you by completing our online registration
today.
• Go to www.garmin.com/vectorowner.
• Keep the original sales receipt, or a photocopy, in a safe
place.
Edge 800 Device Instructions
Pairing Vector with the Edge 800 Device
1
Bring the Edge device within range (3 m) of the sensor.
Appendix
WARNING
on the back of the pedal
to unlocked
.
or a magnet to remove the
(page
2).
NOTE: Stay 10 m away from other ANT+ sensors while
pairing.
2
Turn on the Edge device.
3
Select MENU >
> Bike Settings > Bike Profiles.
4
Select a bike.
5
Select ANT + Power > Power Meter > Yes.
6
Rotate the crank arm a few times.
7
Select .
When the sensor is paired with your Edge device, a message
appears, and
appears solid on the status page. You can
customize a data field to display Vector data.
Calibrating Vector with the Edge 800 Device
1
Enter the crank length
(page
2
Set the install angle of the sensors inside the pedals
(page
2).
3
Calibrate the static zero reference
4
Calibrate Vector before each ride
Entering the Crank Length
The crank length is often printed on the crank arm.
1
Rotate the pedals a few times in order to activate Vector.
2
Select MENU >
> Bike Settings > Bike Profiles.
3
Select a profile.
4
Select Bike Details > Crank Length > Custom.
5
Enter the crank length, and select
Performing a Static Zero Calibration
NOTE: During this task, the bike must be in an upright position,
and nothing can be touching the pedals.
1
Select MENU >
> Bike Settings > Bike Profiles.
2
Select a profile.
3
Select ANT + Power > Calibrate.
When the zero reference is determined, a message appears
on the Edge device.
Edge 500 Device Instructions
Pairing Vector with the Edge 500 Device
1
Bring the Edge device within range (3 m) of the sensor.
NOTE: Stay 10 m away from other ANT+ sensors while
pairing.
2
Turn on the Edge device.
3
Hold MENU.
4
Select Settings > Bike Settings.
5
Select a bike.
6
Select ANT + Power.
7
Enable the sensor, and select Search.
8
Rotate the crank arm a few times.
When the sensor is paired with your Edge device, a message
appears, and
appears solid on the main menu. You can
customize a data field to display Vector data.
Calibrating Vector with the Edge 500 Device
1
Enter the crank length
(page
2
Set the install angle of the sensors inside the pedals
(page
2).
3
Calibrate the static zero reference
4
Calibrate Vector before each ride
Entering the Crank Length
The crank length is often printed on the crank arm.
1
Rotate the pedals a few times in order to activate Vector.
5).
(page
5).
(page
2).
.
5).
(page
6).
(page
2).
5
Hide quick links:
Advertisement
Table of Contents
